The DOI matches its Crossref record; 37 of the 37 references it cites were found in a registry or an index.
Experimental characterization of the mechanical properties of 3D-printed ABS and polycarbonate parts
Abstract
Purpose: This paper aims to present the methodology and results of the experimental characterization of three-dimensional (3D) printed acrylonitrile butadiene styrene (ABS) and polycarbonate (PC) parts utilizing digital image correlation (DIC). Design/methodology/approach: Tensile and shear characterizations of ABS and PC 3D-printed parts were performed to determine the extent of anisotropy present in 3D-printed materials. Specimens were printed with varying raster ([+45/−45], [+30/−60], [+15/−75] and [0/90]) and build orientations (flat, on-edge and up-right) to determine the directional properties of the materials. Tensile and Iosipescu shear specimens were printed and loaded in a universal testing machine utilizing two-dimensional (2D) DIC to measure strain. The Poisson’s ratio, Young’s modulus, offset yield strength, tensile strength at yield, elongation at break, tensile stress at break and strain energy density were gathered for each tensile orientation combination. Shear modulus, offset yield strength and shear strength at yield values were collected for each shear combination. Findings: Results indicated that raster and build orientations had negligible effects on the Young’s modulus or Poisson’s ratio in ABS tensile specimens. Shear modulus and shear offset yield strength varied by up to 33 per cent in ABS specimens, signifying that tensile properties are not indicative of shear properties. Raster orientation in the flat build samples reveals anisotropic behavior in PC specimens as the moduli and strengths varied by up to 20 per cent. Similar variations were observed in shear for PC. Changing the build orientation of PC specimens appeared to reveal a similar magnitude of variation in material properties. Originality/value: This article tests tensile and shear specimens utilizing DIC, which has not been employed previously with 3D-printed specimens. The extensive shear testing conducted in this paper has not been previously attempted, and the results indicate the need for shear testing to understand the 3D-printed material behavior fully.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Sutton, M. A., Orteu, J., & Schreier, H. W. (2009) · HAL (Le Centre pour la Communication Scientifique Directe) · doi:10.1007/978-0-387-78747-3 · Cited by 3,182
3-D printing: The new industrial revolution
Berman, B. (2012) · Business Horizons · doi:10.1016/j.bushor.2011.11.003 · Cited by 2,481
Anisotropic material properties of fused deposition modeling ABS
Ahn, S., Montero, M., Odell, D., Roundy, S., & Wright, P. K. (2002) · Rapid Prototyping Journal · doi:10.1108/13552540210441166 · Cited by 2,382
Carroll, B. E., Palmer, T. A., & Beese, A. M. (2015) · Acta Materialia · doi:10.1016/j.actamat.2014.12.054 · Cited by 1,507
Parametric appraisal of mechanical property of fused deposition modelling processed parts
Sood, A. K., Ohdar, R. K., & Mahapatra, S. S. (2010) · Materials & Design · doi:10.1016/j.matdes.2009.06.016 · Cited by 1,318
Vilaro, T., Colin, C., & Bartout, J. D. (2011) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-011-0731-y · Cited by 1,283
Tymrak, B. M., Kreiger, M., & Pearce, J. M. (2014) · Materials & Design · doi:10.1016/j.matdes.2014.02.038 · Cited by 1,244
Active materials by four-dimension printing
Ge, Q., Qi, H. J., & Dunn, M. L. (2013) · Applied Physics Letters · doi:10.1063/1.4819837 · Cited by 785
Ge, Q., Dunn, C. K., Qi, H. J., & Dunn, M. L. (2014) · Smart Materials and Structures · doi:10.1088/0964-1726/23/9/094007 · Cited by 726
Writing in the granular gel medium
Bhattacharjee, T., Zehnder, S. M., Rowe, K. G., Jain, S., Nixon, R. M., Sawyer, W. G., & Angelini, T. E. (2015) · Science Advances · doi:10.1126/sciadv.1500655 · Cited by 635
Cited by
Mechanical characterization of 3D-printed polymers
Dizon, J. R. C., Espera, A. H., Chen, Q., & Advincula, R. C. (2018) · Additive Manufacturing · doi:10.1016/j.addma.2017.12.002 · Cited by 1,340
A critical review on the fused deposition modeling of thermoplastic polymer composites
Penumakala, P. K., Santo, J., & Thomas, A. (2020) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2020.108336 · Cited by 704
Support Structures for Additive Manufacturing: A Review
Jiang, J., Xu, X., & Stringer, J. (2018) · Journal of Manufacturing and Materials Processing · doi:10.3390/jmmp2040064 · Cited by 527
An Overview on Materials and Techniques in 3D Bioprinting Toward Biomedical Application
Vanaei, S., Parizi, M. S., Vanaei, S., Salemizadehparizi, F., & Vanaei, H. R. (2021) · Engineered Regeneration · doi:10.1016/j.engreg.2020.12.001 · Cited by 308
Cuan-Urquizo, E., Barocio, E., Tejada-Ortigoza, V., Pipes, R. B., Rodriguez, C. A., & Roman-Flores, A. (2019) · Materials · doi:10.3390/ma12060895 · Cited by 288
Metadata
- Authors
- Cantrell, J. T., Rohde, S., Damiani, D., Gurnani, R., DiSandro, L., Anton, J., Young, A., Jerez, A., Steinbach, D., Kroese, C., & Ifju, P. G.
- Venue
- Rapid Prototyping Journal
- Publisher
- Emerald
- Published
- 2017-06-20
- Volume
- 23
- Issue
- 4
- Pages
- 811-824
- ISSN
- 1355-2546 (ISSN-L)
- OpenAlex
- W2512199170
- Cited by
- 433
- References
- 37
- FWCI
- 26.40
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Experimental characterization of the mechanical properties of 3D-printed ABS and polycarbonate parts. https://app.cochat.ai/papers/10.1108/rpj-03-2016-0042
- The paper
- Cantrell, J. T., Rohde, S., Damiani, D., Gurnani, R., DiSandro, L., Anton, J., Young, A., Jerez, A., Steinbach, D., Kroese, C., & Ifju, P. G. (2017). Experimental characterization of the mechanical properties of 3D-printed ABS and polycarbonate parts. Rapid Prototyping Journal. https://doi.org/10.1108/rpj-03-2016-0042
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.