The DOI matches its Crossref record.
Thermographic measurements of the commercial laser powder bed fusion process at NIST
Open accessAbstract
Purpose: Quantitative understanding of the temperatures, gradients and heating/cooling rates in and around the melt pool in laser powder bed fusion (L-PBF) is essential for simulation, monitoring and controls development. The research presented here aims to detail experiment design and preliminary results of high speed, high magnification, in-situ thermographic monitoring setup on a commercial L-PBF system designed to capture temperatures and dynamic process phenomena. Design/methodology/approach: A custom door with angled viewport was designed for a commercial L-PBF system which allows close access of an infrared camera. Preliminary finite element simulations provided size, speed and scale requirements to design camera and optics setup to capture melt pool region temperatures at high magnification and frame rate speed. A custom thermal calibration allowed maximum measurable temperature range of 500°C to 1,025°C. Raw thermographic image data were converted to temperature assuming an emissivity of 0.5. Quantitative temperature results are provided with qualitative observations with discussion regarding the inherent challenges to future thermographic measurements and process monitoring. Findings: Isotherms around the melt pool change in size depending on the relative location of the laser spot with respect to the stripe edges. Locations near the edges of a stripe are cooled to lower temperatures than the center of a stripe. Temperature gradients are highly localized because of rough or powdery surface. At a specific location, temperatures rise from below the measurable temperature range to above (<550°C to >1100°C) within two frames (<1.11 m/s). Particle ejection is a notable phenomenon with measured ejection speeds >11.7 m/s. Originality/value: Several works are detailed in the Introduction of this paper that detail high-speed visible imaging (not thermal imaging) of custom or commercial LBPF processes, and lower-speed thermographic measurements for defect detection. However, no work could be found that provides calibrated, high-speed temperature data from a melt-pool monitoring configuration on a commercial L-PBF system. In addition, the paper elucidates several sources of measurement uncertainty (e.g. calibration, emissivity and time and spatial resolution), describes inherent measurement challenges based on observations of the thermal images and discusses on the implications to model validation and process monitoring and control.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Process defects and in situ monitoring methods in metal powder bed fusion: a review
Grasso, M., & Colosimo, B. M. (2017) · Measurement Science and Technology · doi:10.1088/1361-6501/aa5c4f · Cited by 833
Dynamics of pore formation during laser powder bed fusion additive manufacturing
Martin, A. A., Calta, N. P., Khairallah, S. A., Wang, J., Depond, P. J., Fong, A. Y., Thampy, V., Guss, G. M., Kiss, A. M., Stone, K. H., et al. (2019) · Nature Communications · doi:10.1038/s41467-019-10009-2 · Cited by 711
Guo, Q., Zhao, C., Escano, L. I., Young, Z., Xiong, L., Fezzaa, K., Everhart, W., Brown, B., Sun, T., & Chen, L. (2018) · Acta Materialia · doi:10.1016/j.actamat.2018.03.036 · Cited by 409
Zhang, Y., Hong, G. S., Ye, D., Zhu, K., & Fuh, J. Y. H. (2018) · Materials & Design · doi:10.1016/j.matdes.2018.07.002 · Cited by 335
Criales, L. E., Arısoy, Y. M., Lane, B., Moylan, S., Donmez, A., & Özel, T. (2017) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2017.03.004 · Cited by 309
Self-citation
Metadata
- Authors
- Lane, B., Moylan, S., Whitenton, E. P., & Ma, L.
- Venue
- Rapid Prototyping Journal
- Publisher
- Emerald
- Published
- 2016-08-15
- Volume
- 22
- Issue
- 5
- Pages
- 778-787
- ISSN
- 1355-2546 (ISSN-L)
- OpenAlex
- W2518352236
- Cited by
- 175
- References
- 0
- FWCI
- 17.12
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Thermographic measurements of the commercial laser powder bed fusion process at NIST. https://app.cochat.ai/papers/10.1108/rpj-11-2015-0161
- The paper
- Lane, B., Moylan, S., Whitenton, E. P., & Ma, L. (2016). Thermographic measurements of the commercial laser powder bed fusion process at NIST. Rapid Prototyping Journal. https://doi.org/10.1108/rpj-11-2015-0161
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.