The DOI matches its Crossref record; 11 of the 11 references it cites were found in a registry or an index.
An exploration of binder jetting of copper
Open accessAbstract
Purpose: – The purpose of this paper is to explore the use of binder jetting to fabricate high-purity copper parts. The ability to fabricate geometrically complex copper shapes would have implications on the design and manufacture of components for thermal management systems and structural electronics. Design/methodology/approach: – To explore the feasibility of processing copper via binder jetting, the authors followed an established material development process that encompasses powder selection and tuning process parameters in printing and thermal cycles. Specifically, the authors varied powder size and sintering cycles to explore their effects on densification. Findings: – Three differently sized copper powders were successfully printed, followed by sintering in a reducing atmosphere. It was found that a 15-μm-diameter powder with a sintering cycle featuring a 1,080°C maximum temperature provides the most dense (85 per cent) and pure (97 per cent) final copper parts of the parameters tested. Research limitations/implications: – Due to powder-based additive manufacturing techniques’ inherent limitations in powder packing and particle size diameter, there are difficulties in creating fully dense copper parts. To improve thermal, electrical and mechanical properties, future work will focus on improving densification. Originality/value: – The paper demonstrates the first use of binder jetting to fabricate copper artifacts. The resulting copper parts are denser than what is typically found in binder jetting of metal powders (without infiltration); significant opportunity remains to further optimize the manufacturing process by introducing novel techniques to tailor the material properties for thermal/electrical applications.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Metal Fabrication by Additive Manufacturing Using Laser and Electron Beam Melting Technologies
Murr, L. E., Gaytan, S. M., Ramirez, D. A., Martinez, E., Hernandez, J., Amato, K. N., Shindo, P. W., Medina, F. R., & Wicker, R. B. (2012) · Journal of Materials Science & Technology · doi:10.1016/s1005-0302(12)60016-4 · Cited by 1,686
Leong, K. F., Cheah, C. M., & Chua, C. K. (2003) · Biomaterials · doi:10.1016/s0142-9612(03)00030-9 · Cited by 1,076
Scaffold development using 3D printing with a starch-based polymer
Lam, C. X. F., Mo, X. M., Teoh, S. H., & Hutmacher, D. W. (2002) · Materials Science and Engineering: C · doi:10.1016/s0928-4931(02)00012-7 · Cited by 614
A review of process development steps for new material systems in three dimensional printing (3DP)
Utela, B., Storti, D., Anderson, R., & Ganter, M. (2008) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2009.03.002 · Cited by 548
Ramirez, D. A., Murr, L. E., Martinez, E., Hernandez, D. H., Martinez, J. L., Machado, B. I., Medina, F., Frigola, P., & Wicker, R. B. (2011) · Acta Materialia · doi:10.1016/j.actamat.2011.03.033 · Cited by 217
Open-cellular copper structures fabricated by additive manufacturing using electron beam melting
Ramirez, D. A., Murr, L. E., Li, S. J., Tian, Y. X., Martinez, E., Martinez, J. L., Machado, B. I., Gaytan, S. M., Medina, F., & Wicker, R. B. (2011) · Materials Science and Engineering: A · doi:10.1016/j.msea.2011.03.053 · Cited by 169
Bourell, D. L., Leu, M. C., & Rosen, D. W. (2009) · Cited by 167
Bonding characteristics during very high power ultrasonic additive manufacturing of copper
Sriraman, M. R., Babu, S. S., & Short, M. (2010) · Scripta Materialia · doi:10.1016/j.scriptamat.2009.12.040 · Cited by 145
Sriraman, M. R., Gonser, M., Fujii, H. T., Babu, S. S., & Bloss, M. (2011) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2011.05.003 · Cited by 105
Processing of polycaprolactone porous structure for scaffold development
Tay, B. Y., Zhang, S., Myint, M. H., Ng, F. L., Chandrasekaran, M., & Tan, L. K. A. (2006) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2006.07.016 · Cited by 74
Cited by
Additive manufacturing (3D printing): A review of materials, methods, applications and challenges
Ngo, T. D., Kashani, A., Imbalzano, G., Nguyen, K. T. Q., & Hui, D. (2018) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.02.012 · Cited by 8,431
Binder jetting: A review of process, materials, and methods
Ziaee, M., & Crane, N. B. (2019) · Additive Manufacturing · doi:10.1016/j.addma.2019.05.031 · Cited by 819
Fayazfar, H., Salarian, M., Rogalsky, A., Sarker, D., Russo, P., Paserin, V., & Toyserkani, E. (2018) · Materials & Design · doi:10.1016/j.matdes.2018.02.018 · Cited by 665
Qi, X., Chen, G., Li, Y., Cheng, X., & Li, C. (2019) · Engineering · doi:10.1016/j.eng.2019.04.012 · Cited by 529
Additive Manufacturing of Metallic Materials: A Review
Zhang, Y., Wu, L., Guo, X., Kane, S., Deng, Y., Jung, Y.-G., Lee, J.-H., & Zhang, J. (2018) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-017-2747-y · Cited by 521
Metadata
- Authors
- Bai, Y., & Williams, C. B.
- Venue
- Rapid Prototyping Journal
- Publisher
- Emerald
- Published
- 2015-03-16
- Volume
- 21
- Issue
- 2
- Pages
- 177-185
- ISSN
- 1355-2546 (ISSN-L)
- OpenAlex
- W2030362608
- Cited by
- 270
- References
- 11
- FWCI
- 13.40
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: An exploration of binder jetting of copper. https://app.cochat.ai/papers/10.1108/rpj-12-2014-0180
- The paper
- Bai, Y., & Williams, C. B. (2015). An exploration of binder jetting of copper. Rapid Prototyping Journal. https://doi.org/10.1108/rpj-12-2014-0180
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.