The DOI matches its Crossref record.
Mechanical properties and microstructural characterization of selective laser melted 17-4 PH stainless steel
Abstract
Abstract Purpose The purpose of this paper is to understand the effect of four different factors: building orientation, heat treatment (solution annealing and aging), thermal history and process parameters on the mechanical properties and microstructural features of 17-4 precipitation hardening (PH) stainless steel (SS) parts produced using selective laser melting (SLM). Design/methodology/approach Various sets of test samples were built on a ProX 100™ SLM system under argon environment. Characterization studies were conducted using mechanical tensile and compression test, microhardness test, optical microscopy, X-ray diffraction and scanning electron microscopy. Findings Results indicate that building orientation has a direct effect on the mechanical properties of SLM parts, as vertically built samples exhibit lower yield and tensile strengths and elongation to failure. Post-SLM heat treatment proved to have positive effects on part strength and hardness, but it resulted in reduced ductility. Longer inter-layer time intervals between the melting of successive layers allow for higher austenite content because of lower cooling rates, thus decreasing material hardness. On the other hand, tensile properties such as elongation to failure, yield strength and tensile strength were not significantly affected by the change in inter-layer time intervals. Similar to other AM processes, SLM process parameters were shown to be instrumental in achieving desirable part properties. It is shown that without careful setting of process parameters, parts with defects (porosity and unmelted powder particles) can be produced. Originality/value Although the manufacturing of 17-4 PH SS using SLM has been investigated in the literature, the paper provides the first comprehensive study on the effect of different factors on mechanical properties and microstructure of SLM 17-4 PH. Optimizing process parameters and using heat treatment are shown to improve the properties of the part.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Additive manufacturing of fatigue resistant materials: Challenges and opportunities
Yadollahi, A., & Shamsaei, N. (2017) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2017.01.001 · Cited by 1,023
Self-citationSteels in additive manufacturing: A review of their microstructure and properties
Bajaj, P., Hariharan, A., Kini, A., Kürnsteiner, P., Raabe, D., & Jägle, E. A. (2020) · Materials Science and Engineering: A · doi:10.1016/j.msea.2019.138633 · Cited by 1,020
Additive manufacturing of steels: a review of achievements and challenges
Haghdadi, N., Laleh, M., Moyle, M., & Primig, S. (2021) · Journal of Materials Science · doi:10.1007/s10853-020-05109-0 · Cited by 622
Narasimharaju, S. R., Zeng, W., See, T. L., Zhu, Z., Scott, P., Jiang, X., & Lou, S. (2022) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2021.12.033 · Cited by 508
Defects and anomalies in powder bed fusion metal additive manufacturing
Mostafaei, A., Zhao, C., He, Y., Reza Ghiaasiaan, S., Shi, B., Shao, S., Shamsaei, N., Wu, Z., Kouraytem, N., Sun, T., et al. (2022) · Current Opinion in Solid State and Materials Science · doi:10.1016/j.cossms.2021.100974 · Cited by 491
Self-citation
Metadata
- Authors
- Mahmoudi, M., Elwany, A., Yadollahi, A., Thompson, S. M., Bian, L., & Shamsaei, N.
- Venue
- Rapid Prototyping Journal
- Publisher
- Emerald
- Published
- 2017-03-20
- Volume
- 23
- Issue
- 2
- Pages
- 280-294
- ISSN
- 1355-2546 (ISSN-L)
- OpenAlex
- W2606769664
- Cited by
- 176
- References
- 0
- FWCI
- 11.60
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Mechanical properties and microstructural characterization of selective laser melted 17-4 PH stainless steel. https://app.cochat.ai/papers/10.1108/rpj-12-2015-0192
- The paper
- Mahmoudi, M., Elwany, A., Yadollahi, A., Thompson, S. M., Bian, L., & Shamsaei, N. (2017). Mechanical properties and microstructural characterization of selective laser melted 17-4 PH stainless steel. Rapid Prototyping Journal. https://doi.org/10.1108/rpj-12-2015-0192
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.