The DOI matches its Crossref record; 9 of the 9 references it cites were found in a registry or an index.
3D Printing for the Rapid Prototyping of Structural Electronics
Open accessAbstract
In new product development, time to market (TTM) is critical for the success and profitability of next generation products. When these products include sophisticated electronics encased in 3D packaging with complex geometries and intricate detail, TTM can be compromised - resulting in lost opportunity. The use of advanced 3D printing technology enhanced with component placement and electrical interconnect deposition can provide electronic prototypes that now can be rapidly fabricated in comparable time frames as traditional 2D bread-boarded prototypes; however, these 3D prototypes include the advantage of being embedded within more appropriate shapes in order to authentically prototype products earlier in the development cycle. The fabrication freedom offered by 3D printing techniques, such as stereolithography and fused deposition modeling have recently been explored in the context of 3D electronics integration - referred to as 3D structural electronics or 3D printed electronics. Enhanced 3D printing may eventually be employed to manufacture end-use parts and thus offer unit-level customization with local manufacturing; however, until the materials and dimensional accuracies improve (an eventuality), 3D printing technologies can be employed to reduce development times by providing advanced geometrically appropriate electronic prototypes. This paper describes the development process used to design a novelty six-sided gaming die. The die includes a microprocessor and accelerometer, which together detect motion and upon halting, identify the top surface through gravity and illuminate light-emitting diodes for a striking effect. By applying 3D printing of structural electronics to expedite prototyping, the development cycle was reduced from weeks to hours.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
A comparison of rapid prototyping technologies
Pham, D. T., & Gault, R. S. (1998) · International Journal of Machine Tools and Manufacture · doi:10.1016/s0890-6955(97)00137-5 · Cited by 915
3D Printing multifunctionality: structures with electronics
Espalin, D., Muse, D. W., MacDonald, E., & Wicker, R. B. (2014) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-014-5717-7 · Cited by 614
Self-citationJoe Lopes, A., MacDonald, E., & Wicker, R. B. (2012) · Rapid Prototyping Journal · doi:10.1108/13552541211212113 · Cited by 399
Self-citationLaser Direct-Write Techniques for Printing of Complex Materials
Arnold, C. B., Serra, P., & Piqué, A. (2007) · MRS Bulletin · doi:10.1557/mrs2007.11 · Cited by 360
Multi-material, multi-technology stereolithography
Wicker, R. B., & MacDonald, E. W. (2012) · Virtual and Physical Prototyping · doi:10.1080/17452759.2012.721119 · Cited by 93
Self-citationRapid tooling technology. Part 1. A comparative study
Chua, C. K., Hong, K. H., & Ho, S. L. (1999) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s001700050108 · Cited by 85
Microstructural and Process Characterization of Conductive Traces Printed from Ag Particulate Inks
Roberson, D. A., Wicker, R. B., Murr, L. E., Church, K., & MacDonald, E. W. (2011) · Materials · doi:10.3390/ma4060963 · Cited by 67
Self-citationStructurally Embedded Electrical Systems Using Ultrasonic Consolidation (UC)
Siggard, E. J., Madhusoodanan, A. S., Stucker, B. E., & Eames, B. (2006) · doi:10.26153/tsw/7118 · Cited by 43
Layered Manufacturing With Embedded Components: Process Planning Considerations
Cham, J. G., Pruitt, B. L., Cutkosky, M. R., Binnard, M., Weiss, L. E., & Neplotnik, G. (1999) · ASME International Design Engineering Technical Conferences and Computers and Information in Engineering Conference (IDETC/CIE) · doi:10.1115/detc99/dfm-8910 · Cited by 33
Cited by
Additive manufacturing (3D printing): A review of materials, methods, applications and challenges
Ngo, T. D., Kashani, A., Imbalzano, G., Nguyen, K. T. Q., & Hui, D. (2018) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.02.012 · Cited by 8,431
3D printing of polymer matrix composites: A review and prospective
Wang, X., Jiang, M., Zhou, Z., Gou, J., & Hui, D. (2017) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2016.11.034 · Cited by 3,325
Multiprocess 3D printing for increasing component functionality
MacDonald, E., & Wicker, R. (2016) · Science · doi:10.1126/science.aaf2093 · Cited by 961
Self-citation3D printing technologies for electrochemical energy storage
Zhang, F., Wei, M., Viswanathan, V. V., Swart, B., Shao, Y., Wu, G., & Zhou, C. (2017) · Nano Energy · doi:10.1016/j.nanoen.2017.08.037 · Cited by 494
Fused deposition modeling: process, materials, parameters, properties, and applications
Rajan, K., Samykano, M., Kadirgama, K., Harun, W. S. W., & Rahman, M. M. (2022) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-022-08860-7 · Cited by 426
Metadata
- Authors
- Macdonald, E., Salas, R., Espalin, D., Perez, M., Aguilera, E., Muse, D., & Wicker, R. B.
- Venue
- IEEE Access
- Published
- 2014-12
- Volume
- 2
- Pages
- 234-242
- ISSN
- 2169-3536 (ISSN-L)
- OpenAlex
- W2045279221
- Cited by
- 606
- References
- 9
- FWCI
- 55.56
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: 3D Printing for the Rapid Prototyping of Structural Electronics. https://app.cochat.ai/papers/10.1109/access.2014.2311810
- The paper
- Macdonald, E., Salas, R., Espalin, D., Perez, M., Aguilera, E., Muse, D., & Wicker, R. B. (2014). 3D Printing for the Rapid Prototyping of Structural Electronics. IEEE Access. https://doi.org/10.1109/access.2014.2311810
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.