The DOI matches its Crossref record.
Estimation of inertial parameters of rigid body links of manipulators
Open accessAbstract
A method of estimating the mass, the location of center of mass, and the moments of inertia of each rigid body link of a robot during general manipulator movement is presented. The algorithm is derived from the Newton-Euler equations, and uses measurements of the joint torques as well as the measurement and calculation of the kinematics of the manipulator while it is moving. The identification equations are linear in the desired unknown parameters, and a modified least squares algorithm is used to obtain estimates of these parameters. Some of the parameters, however, are not identifiable due to the restricted motion of proximal links and the lack of full force/torque sensing. The algorithm was implemented on the MIT Serial Link Direct Drive Arm. A good match was obtained between joint torques predicted from the estimated parameters and the joint torques computed from motor currents.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Adaptive motion control of rigid robots: A tutorial
Ortega, R., & Spong, M. W. (1989) · Automatica · doi:10.1016/0005-1098(89)90054-x · Cited by 1,238
Adaptive manipulator control: A case study
Slotine, J.-J. E., & Weiping, L. (1988) · IEEE Transactions on Automatic Control · doi:10.1109/9.14411 · Cited by 1,032
Composite adaptive control of robot manipulators
Slotine, J.-J. E., & Li, W. (1989) · Automatica · doi:10.1016/0005-1098(89)90094-0 · Cited by 612
Estimation of Inertial Parameters of Manipulator Loads and Links
Atkeson, C. G., An, C. H., & Hollerbach, J. M. (1986) · The International Journal of Robotics Research · doi:10.1177/027836498600500306 · Cited by 590
Self-citationDirect calculation of minimum set of inertial parameters of serial robots
Gautier, M., & Khalil, W. (1990) · IEEE Transactions on Robotics and Automation · doi:10.1109/70.56655 · Cited by 412
Adaptive control of robot manipulators with flexible joints
Lozano, R., & Brogliato, B. (1992) · IEEE Transactions on Automatic Control · doi:10.1109/9.121619 · Cited by 271
Metadata
- Authors
- An, C., Atkeson, C., & Hollerbach, J.
- Venue
- 1985 24th IEEE Conference on Decision and Control
- Publisher
- IEEE
- Published
- 1985-12
- Pages
- 990-995
- ISSN
- 0191-2216 (ISSN-L)
- OpenAlex
- W2079315820
- Cited by
- 221
- References
- 0
- FWCI
- 17.39
- Type
- conference paper
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.