The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
Power Comparison Between High-Speed Electrical and Optical Interconnects for Interchip Communication
Abstract
An I/O bandwidth commensurate with a dramatically increasing on-chip computational capability is highly desirable. Achieving this goal using board-level copper interconnects in the future will become increasingly challenging owing to severe increase in high-frequency, skin-effect and dielectric loss, noise due to crosstalk, impedance mismatch, and package reflections. The solutions designed to overcome these deleterious effects require complex signal processing at the interconnect endpoints, which results in a larger power and area requirement. Optical interconnects offer a powerful alternative, potentially at a lower power. Prior work in comparing the two technologies has entailed overly simplified assumptions pertaining to either the optical or the electrical system. In this paper, we draw a more realistic power comparison with respect to the relevant parameters such as bandwidth, interconnect length and bit error rate (BER) by capturing the essential complexity in both types of interconnect systems. At the same time, we preserve the simplicity by using mostly analytical models, verified by SPICE simulations where possible. We also identify critical device and system parameters, which have a large effect on power dissipation in each type of interconnect, while quantifying the severity of their impact. For optical interconnect, these parameters are detector and modulator capacitance, responsivity, coupling efficiency and modulator type; whereas, in the case of electrical system, the critical parameters include receiver sensitivity/offset and impedance mismatch. Toward this end, we first present an optimization scheme to minimize optical interconnect power and quantify its performance as a function of future technology nodes. Next, on the electrical interconnect side, we examine the power dissipation of a state-of-the-art electrical interconnect, which uses simultaneous bidirectional signaling with transmitter equalization and on-chip noise cancellation. Finally, we draw extensive comparisons between optical and electrical interconnects. As an example, for bandwidth of 6 Gb/s at 100 nm technology node, lengths greater than the critical length of about 43 cm yields lower power in optical interconnects. This length becomes lower (making optics more favorable) with higher data rates and lower bit error rate requirement.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Rationale and challenges for optical interconnects to electronic chips
Miller, D. A. B. (2000) · Proceedings of the IEEE · doi:10.1109/5.867687 · Cited by 1,189
Cited by
Device Requirements for Optical Interconnects to Silicon Chips
Miller, D. (2009) · Proceedings of the IEEE · doi:10.1109/jproc.2009.2014298 · Cited by 1,966
Strong quantum-confined Stark effect in germanium quantum-well structures on silicon
Kuo, Y.-H., Lee, Y. K., Ge, Y., Ren, S., Roth, J. E., Kamins, T. I., Miller, D. A. B., & Harris, J. S. (2005) · Nature · doi:10.1038/nature04204 · Cited by 802
Metadata
- Authors
- Cho, H., Kapur, P., & Saraswat, K. C.
- Venue
- Journal of Lightwave Technology
- Published
- 2004-09
- Volume
- 22
- Issue
- 9
- Pages
- 2021-2033
- ISSN
- 0733-8724 (ISSN-L)
- OpenAlex
- W2050117348
- Cited by
- 192
- References
- 1
- FWCI
- 13.08
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Power Comparison Between High-Speed Electrical and Optical Interconnects for Interchip Communication. https://app.cochat.ai/papers/10.1109/jlt.2004.833531
- The paper
- Cho, H., Kapur, P., & Saraswat, K. C. (2004). Power Comparison Between High-Speed Electrical and Optical Interconnects for Interchip Communication. Journal of Lightwave Technology. https://doi.org/10.1109/jlt.2004.833531
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.