The DOI matches its Crossref record; 19 of the 19 references it cites were found in a registry or an index.
PCA-Based Feature Selection Scheme for Machine Defect Classification
Abstract
The sensitivity of various features that are characteristic of a machine defect may vary considerably under different operating conditions. Hence it is critical to devise a systematic feature selection scheme that provides guidance on choosing the most representative features for defect classification. This paper presents a feature selection scheme based on the principal component analysis (PCA) method. The effectiveness of the scheme was verified experimentally on a bearing test bed, using both supervised and unsupervised defect classification approaches. The objective of the study was to identify the severity level of bearing defects, where no a priori knowledge on the defect conditions was available. The proposed scheme has shown to provide more accurate defect classification with fewer feature inputs than using all features initially considered relevant. The result confirms its utility as an effective tool for machine health assessment.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Neural Networks: A Comprehensive Foundation
Haykin, S. (1998) · Cited by 30,070
(2012) · Encyclopedia of the Sciences of Learning · doi:10.1007/978-1-4419-1428-6_5195 · Cited by 19,370
Chiang, L. H., Russell, E. L., & Braatz, R. D. (2001) · Advanced Textbooks in Control and Signal Processing · doi:10.1007/978-1-4471-0347-9_3 · Cited by 5,003
Low-dimensional procedure for the characterization of human faces
Sirovich, L., & Kirby, M. (1987) · Journal of the Optical Society of America A · doi:10.1364/josaa.4.000519 · Cited by 2,311
Harris, T. A., & Crecelius, W. J. (1986) · Journal of Tribology · doi:10.1115/1.3261135 · Cited by 1,701
Neural and adaptive systems : fundamentals through simulations
Príncipe, J. C., Euliano, N. R., & Lefebvre, W. (2000) · CERN Document Server (European Organization for Nuclear Research) · Cited by 818
Taylor, C. M. (1992) · Wear · doi:10.1016/0043-1648(92)90098-s · Cited by 718
EFFECTIVENESS AND SENSITIVITY OF VIBRATION PROCESSING TECHNIQUES FOR LOCAL FAULT DETECTION IN GEARS
DALPIAZ, G., RIVOLA, A., & RUBINI, R. (2000) · Mechanical Systems and Signal Processing · doi:10.1006/mssp.1999.1294 · Cited by 338
Adaptive prognostics for rolling element bearing condition
Li, Y., Billington, S. A., Zhang, C., Kurfess, T. R., Danyluk, S., & Liang, S. Y. (1999) · Mechanical Systems and Signal Processing · doi:10.1006/mssp.1998.0183 · Cited by 244
Prediction of Machine Deterioration Using Vibration Based Fault Trends and Recurrent Neural Networks
Tse, P. W., & Atherton, D. P. (1999) · Journal of Vibration and Acoustics · doi:10.1115/1.2893988 · Cited by 178
Monitoring and diagnosis of rolling element bearings using artificial neural networks
Alguindigue, I. E., Loskiewicz-Buczak, A., & Uhrig, R. E. (1993) · IEEE Transactions on Industrial Electronics · doi:10.1109/41.222642 · Cited by 175
Prognosis of remaining bearing life using neural networks
Shao, Y., & Nezu, K. (2000) · Proceedings of the Institution of Mechanical Engineers, Part I: Journal of Systems and Control Engineering · doi:10.1243/0959651001540582 · Cited by 160
A COMPARISON OF AUTOREGRESSIVE MODELING TECHNIQUES FOR FAULT DIAGNOSIS OF ROLLING ELEMENT BEARINGS
Baillie, D. C., & Mathew, J. (1996) · Mechanical Systems and Signal Processing · doi:10.1006/mssp.1996.0001 · Cited by 156
Support vector machines for detection and characterization of rolling element bearing faults
Jack, L. B., & Nandi, A. K. (2001) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/095440620121500907 · Cited by 101
New Statistical Moments for Diagnostics of Rolling Element Bearings
Honarvar, F., & Martin, H. R. (1997) · Journal of Manufacturing Science and Engineering · doi:10.1115/1.2831123 · Cited by 64
A virtual instrumentation system for integrated bearing condition monitoring
Wang, C., & Gao, R. X. (2000) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/19.843072 · Cited by 56
Self-citationIntelligent monitoring of ball bearing conditions
Liu, T. I., & Mengel, J. M. (1992) · Mechanical Systems and Signal Processing · doi:10.1016/0888-3270(92)90066-r · Cited by 53
Tool Condition Monitoring in Machining by Fuzzy Neural Networks
Li, S., & Elbestawi, M. A. (1996) · Journal of Dynamic Systems Measurement and Control · doi:10.1115/1.2802341 · Cited by 51
Algazi, V. R., Brown, K. L., Ready, M. J., et al. (1993) · IEEE Transactions on Speech and Audio Processing · doi:10.1109/89.222877 · Cited by 17
Cited by
Deep learning and its applications to machine health monitoring
Zhao, R., Yan, R., Chen, Z., Mao, K., Wang, P., & Gao, R. X. (2019) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2018.05.050 · Cited by 2,894
Self-citationWavelets for fault diagnosis of rotary machines: A review with applications
Yan, R., Gao, R. X., & Chen, X. (2014) · Signal Processing · doi:10.1016/j.sigpro.2013.04.015 · Cited by 1,446
Self-citationDeep Learning Algorithms for Bearing Fault Diagnostics—A Comprehensive Review
Zhang, S., Zhang, S., Wang, B., & Habetler, T. G. (2020) · IEEE Access · doi:10.1109/access.2020.2972859 · Cited by 913
A survey on deep learning based bearing fault diagnosis
Hoang, D.-T., & Kang, H.-J. (2019) · Neurocomputing · doi:10.1016/j.neucom.2018.06.078 · Cited by 866
Ben Ali, J., Chebel-Morello, B., Saidi, L., Malinowski, S., & Fnaiech, F. (2015) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2014.10.014 · Cited by 502
Metadata
- Authors
- Malhi, A., & Gao, R. X.
- Venue
- IEEE Transactions on Instrumentation and Measurement
- Published
- 2004-12
- Volume
- 53
- Issue
- 6
- Pages
- 1517-1525
- ISSN
- 0018-9456 (ISSN-L)
- OpenAlex
- W2141188346
- Cited by
- 579
- References
- 19
- FWCI
- 12.85
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.