A Lithium-Ion Battery-in-the-Loop Approach to Test and Validate Multiscale Dual H Infinity Filters for State-of-Charge and Capacity Estimation
The DOI matches its Crossref record; 37 of the 37 references it cites were found in a registry or an index.
Abstract
An accurate battery capacity and state estimation method is one of the most significant and difficult techniques to ensure efficient and safe operation of the batteries for electric vehicles (EVs). Since capacity and state of charge (SoC) are strongly correlated, the SoC is hardly to be accurately estimated without knowing accurate battery capacity. Thus, a multiscale dual H infinity filter (HIF) has been proposed to estimate battery SoC and capacity in real time with dual timescales in response to slow-varying battery parameters and fast-varying battery state. The proposed method is first evaluated and verified using off-line experimental data and then compared with the single/multiscale dual Kalman filters (KFs). The results show that the proposed multiscale dual HIFs has better robustness and higher estimation accuracy than the single/multiscale dual KFs. To further validate the feasibility of the proposed method for EV applications, a lithium-ion battery-in-the-loop approach is applied to verify the stability and accuracy of the SoC estimation, and it is found that the SoC estimated from the proposed method can converge to the reference value gradually and be stabilized within 2%.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“Te approach of H ∞ pays attention to these uncertainties, together with others from the exterior, meaning that it results in maximum accuracy [58].”
Citations
Cites
A review on lithium-ion battery ageing mechanisms and estimations for automotive applications
Barré, A., Deguilhem, B., Grolleau, S., Gérard, M., Suard, F., & Riu, D. (2013) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.05.040 · Cited by 1,758 · cited 1×
“W ITH the superiority of high specific energy and specific power, lithium-ion batteries are widely used in the development of electric vehicles (EVs) [1], [2].”
BackgroundNg, K. S., Moo, C.-S., Chen, Y.-P., & Hsieh, Y.-C. (2009) · Applied Energy · doi:10.1016/j.apenergy.2008.11.021 · Cited by 1,636 · cited 1×
“ampere–hour methods [6], model-based methods [7]–[9], and data-driven methods, including neural networks [10], fuzzy controllers [11], and support vector regressions [12].”
MethodState-of-Charge Estimation for Lithium-Ion Batteries Using Neural Networks and EKF
Charkhgard, M., & Farrokhi, M. (2010) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2010.2043035 · Cited by 779 · cited 2×
“The extended KF (EKF) shows a good estimation of the SoC with a fast convergence at erroneous initial values of SoCs in [10].”
BackgroundMethodMaharjan, L., Inoue, S., Akagi, H., & Asakura, J. (2009) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2009.2014868 · Cited by 590 · cited 6×
“For the practical applications in EVs, online identification of battery parameters is proposed to update battery parameters regularly in [24] and [25], such as a moving-window least square method in [25], which leads to the exploration of the joint estimation of battery states and parameters such as a recursive least…”
BackgroundInfluentialXiong, R., Sun, F., Chen, Z., & He, H. (2014) · Applied Energy · doi:10.1016/j.apenergy.2013.07.061 · Cited by 529
Self-citationSupport Vector Machines Used to Estimate the Battery State of Charge
Álvarez Antón, J. C., García Nieto, P. J., Blanco Viejo, C., & Vilán Vilán, J. A. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2013.2243918 · Cited by 512 · cited 1×
“ampere–hour methods [6], model-based methods [7]–[9], and data-driven methods, including neural networks [10], fuzzy controllers [11], and support vector regressions [12].”
MethodRahimi-Eichi, H., Baronti, F., & Chow, M.-Y. (2014) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2013.2263774 · Cited by 380 · cited 2×
“moving-window least square method in [25], which leads to the exploration of the joint estimation of battery states and parameters such as a recursive least square (RLS) and an AEKF in”
MethodDai, H., Wei, X., Sun, Z., Wang, J., & Gu, W. (2012) · Applied Energy · doi:10.1016/j.apenergy.2012.02.044 · Cited by 367 · cited 1×
“, capacity) require dual estimation methods in different timescales [32], [33], which will not only increase the stability of the estimation methods but also reduce their computation complexity.”
BackgroundMeng, J., Luo, G., & Gao, F. (2016) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2015.2439578 · Cited by 349 · cited 1×
“The adaptive UKF (AUKF) whose process and measurement noise covariance can be adjusted adaptively in the estimation process is proposed to obtain more accurate results than the UKF in [14].”
ResultReview of electrical energy storage system for vehicular applications
Ren, G., Ma, G., & Cong, N. (2015) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2014.08.003 · Cited by 315 · cited 1×
“W ITH the superiority of high specific energy and specific power, lithium-ion batteries are widely used in the development of electric vehicles (EVs) [1], [2].”
BackgroundGrolleau, S., Delaille, A., Gualous, H., Gyan, P., Revel, R., Bernard, J., Redondo-Iglesias, E., & Peter, J. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.11.098 · Cited by 268 · cited 1×
“In [30], the degradation models are established to estimate battery capacity based on a series of experimental data, which is very time consuming.”
BackgroundNonlinear State of Charge Estimator for Hybrid Electric Vehicle Battery
Kim, I.-S. (2008) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2008.924629 · Cited by 261 · cited 2×
“In [9], the resistance–capacitance (RC) model with the nonlinear characteristics of SoC versus opencircuit voltage (OCV) for Li-PB is used to estimate the SoC with the sliding-mode observer.”
MethodZhang, Y., Xiong, R., He, H., & Shen, W. (2017) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2016.2603229 · Cited by 235 · cited 9×
“For the practical applications in EVs, online identification of battery parameters is proposed to update battery parameters regularly in [24] and [25], such as a moving-window least square method in [25], which leads to the exploration of the joint estimation of battery states and parameters such as a recursive least…”
BackgroundMethodInfluentialSelf-citationSun, F., & Xiong, R. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.10.119 · Cited by 210 · cited 1×
“Among them, the Thevenin model is widely used because of its balance between simplicity and accuracy [7], [26], [31].”
MethodSelf-citationKim, J., Lee, S., & Cho, B. H. (2012) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2011.2158554 · Cited by 207 · cited 3×
“In [31], battery capacity is considered as a system parameter and then a dual EKF is proposed to estimate the SoC and capacity online.”
BackgroundMethodElectro-thermal cycle life model for lithium iron phosphate battery
Ye, Y., Shi, Y., & Tay, A. A. O. (2012) · Journal of Power Sources · doi:10.1016/j.jpowsour.2012.06.055 · Cited by 177 · cited 2×
“In fact, this curve is affected by temperature and aging to a certain extent, which mainly reflects in the change of battery capacity [37], [38].”
BackgroundSingh, P., Vinjamuri, R., Wang, X., & Reisner, D. (2006) · Journal of Power Sources · doi:10.1016/j.jpowsour.2005.04.039 · Cited by 177 · cited 1×
“ampere–hour methods [6], model-based methods [7]–[9], and data-driven methods, including neural networks [10], fuzzy controllers [11], and support vector regressions [12].”
MethodLyapunov-Based Adaptive State of Charge and State of Health Estimation for Lithium-Ion Batteries
Chaoui, H., Golbon, N., Hmouz, I., Souissi, R., & Tahar, S. (2015) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2014.2341576 · Cited by 175 · cited 3×
“ampere–hour methods [6], model-based methods [7]–[9], and data-driven methods, including neural networks [10], fuzzy controllers [11], and support vector regressions [12].”
MethodZhang, F., Liu, G., Fang, L., & Wang, H. (2012) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2011.2159691 · Cited by 171 · cited 1×
“The experimental results of the SoC estimation in [21] show that the HIF can provide the accurate SoC estimation at inexact or unknown statistical properties of the errors.”
MethodAung, H., Soon Low, K., & Ting Goh, S. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2014.2361755 · Cited by 145 · cited 1×
“The unscented KF (UKF) is proved to have higher estimation precision and less computational burden than the EKF due to its no requirement of linearizing nonlinear model in [13].”
BackgroundEinhorn, M., Conte, F. V., Kral, C., & Fleig, J. (2012) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2011.2180689 · Cited by 127 · cited 1×
“They can generally be divided into four categories: lookup table methods [5],”
BackgroundTwo Time-Scaled Battery Model Identification With Application to Battery State Estimation
Hu, Y., & Wang, Y.-Y. (2015) · IEEE Transactions on Control Systems Technology · doi:10.1109/tcst.2014.2358846 · Cited by 72 · cited 1×
“, capacity) require dual estimation methods in different timescales [32], [33], which will not only increase the stability of the estimation methods but also reduce their computation complexity.”
BackgroundBattery algorithm verification and development using hardware-in-the-loop testing
He, Y., Liu, W., & Koch, B. J. (2009) · Journal of Power Sources · doi:10.1016/j.jpowsour.2009.11.036 · Cited by 66 · cited 1×
“To further verify the reliability and accuracy of the proposed multiscale dual HIF for the SoC and capacity estimation, the batteryin-loop test based on xPC target [34] is set up to closely simulate EV operation environments for a real-time validation [35], [36].”
MethodCharkhgard, M., & Zarif, M. H. (2015) · IET Power Electronics · doi:10.1049/iet-pel.2014.0523 · Cited by 63 · cited 1×
“Furthermore, the adaptive algorithms for estimating noise covariance matrices are introduced in [22].”
MethodDevelopment of a Hardware-in-the-Loop Simulation System for Testing Cell Balancing Circuits
Lee, W. C., & Drury, D. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2013.2256799 · Cited by 45 · cited 1×
“To further verify the reliability and accuracy of the proposed multiscale dual HIF for the SoC and capacity estimation, the batteryin-loop test based on xPC target [34] is set up to closely simulate EV operation environments for a real-time validation [35], [36].”
MethodOn-line battery identification for electric driving range prediction
Kessels, J. T. B. A., Rosca, B., Bergveld, H. J., & van den Bosch, P. P. J. (2011) · 2011 IEEE Vehicle Power and Propulsion Conference · doi:10.1109/vppc.2011.6043022 · Cited by 43 · cited 2×
“To overcome this problem, many methods have been investigated to estimate battery capacity in real time [28]–[31].”
MethodOnline Parameter Identification of Lithium-Ion Batteries With Surface Temperature Variations
Chaoui, H., Mejdoubi, A. E., & Gualous, H. (2016) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2016.2583478 · Cited by 38 · cited 1×
“For the practical applications in EVs, online identification of battery parameters is proposed to update battery parameters regularly in [24] and [25], such as a”
Low, K. H., Wang, H., & Wang, M. Y. (2005) · IEEE International Conference on Automation Science and Engineering (CASE) · doi:10.1109/coase.2005.1506793 · Cited by 33 · cited 1×
“To further verify the reliability and accuracy of the proposed multiscale dual HIF for the SoC and capacity estimation, the batteryin-loop test based on xPC target [34] is set up to closely simulate EV operation environments for a real-time validation [35], [36].”
MethodKim, T., Qiao, W., & Qu, L. (2013) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec.2013.6520266 · Cited by 26 · cited 1×
“In [8], the dual polarization (DP) model is used to estimate the SoC based on the particle swarm optimization (PSO).”
MethodCapacity estimation for Li-ion batteries
Tang, X., Mao, X., Lin, J. G., & Koch, B. J. (2011) · Proceedings of the ... American Control Conference/Proceedings of the American Control Conference · doi:10.1109/acc.2011.5991410 · Cited by 26 · cited 1×
“The OCV is utilized to obtain the accurate SoC, which is then used to calculate the battery capacity online [28], [29].”
MethodDiscrete H/sub ∞/ filter design with application to speech enhancement
Shen, X. (2002) · IEEE International Conference on Acoustics Speech and Signal Processing · doi:10.1109/icassp.1995.480570 · Cited by 23
Battery State Estimation Using Mixed Kalman/Hinfinity, Adaptive Luenberger and Sliding Mode Observer
Unterrieder, C., Priewasser, R., Marsili, S., & Huemer, M. (2013) · IEEE Vehicle Power and Propulsion Conference (VPPC) · doi:10.1109/vppc.2013.6671667 · Cited by 22
Fault detection and isolation in an inertial navigation system using a bank of unscented H∞ filters
Vitanov, I., & Aouf, N. (2014) · UKACC International Conference on Control · doi:10.1109/control.2014.6915148 · Cited by 8
Lower-Order $H_{\infty} $ Filter Design for Bilinear Systems With Bounded Inputs
Abraham, E., & Kerrigan, E. C. (2014) · IEEE Transactions on Signal Processing · doi:10.1109/tsp.2014.2385656 · Cited by 7 · cited 1×
“The H infinity filter (HIF) based on the minimax error criterion, which is proposed and improved in [15] and [16], can still guarantee estimation accuracy in the worst case, and it is increasingly popular in the field of state estimation [17]–[20].”
MethodWang, H., Rehman, M. M. U., Evzelman, M., & Zane, R. A. (2015) · IEEE ... Workshop on Control and Modeling for Power Electronics · doi:10.1109/compel.2015.7236519 · Cited by 5 · cited 1×
“For safe and efficient operation of EVs, it is essential for battery management systems to accurately estimate the state of charge (SoC) and capacity so that batteries can be balanced and managed effectively in EVs [3], [4].”
BackgroundEstimation of power quality using Complex H∞ Filter
Sahoo, H. K., Dash, P. K., Rath, N. P., & Kant, R. (2009) · International Conference on Power Systems (ICPS) · doi:10.1109/icpws.2009.5442696 · Cited by 2 · cited 1×
“The H infinity filter (HIF) based on the minimax error criterion, which is proposed and improved in [15] and [16], can still guarantee estimation accuracy in the worst case, and it is increasingly popular in the field of state estimation [17]–[20].”
MethodRobust H∞ filter design for a class of uncertain systems with time-varying state-delays
Ramakrishnan, K. K., & Ray, G. (2012) · International Conference on Electrical and Computer Engineering (ICECE) · doi:10.1109/icece.2012.6471665 · Cited by 1
Research works printed but not linked: 1
- banavar, 1992, A game theoretic approach to linear dynamics estimation, dissertation Univ Texas Austin
Cited by
How, D. N. T., Hannan, M. A., Hossain Lipu, M. S., & Ker, P. J. (2019) · IEEE Access · doi:10.1109/access.2019.2942213 · Cited by 812
Xiong, R., Cao, J., & Yu, Q. (2018) · Applied Energy · doi:10.1016/j.apenergy.2017.11.072 · Cited by 564
Self-citationReview on state-of-health of lithium-ion batteries: Characterizations, estimations and applications
Yang, S., Zhang, C., Jiang, J., Zhang, W., Zhang, L., & Wang, Y. (2021) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2021.128015 · Cited by 435
An Overview and Comparison of Online Implementable SOC Estimation Methods for Lithium-Ion Battery
Meng, J., Ricco, M., Luo, G., Swierczynski, M., Stroe, D.-I., Stroe, A.-I., & Teodorescu, R. (2018) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2017.2775179 · Cited by 393
A deep learning method for online capacity estimation of lithium-ion batteries
Shen, S., Sadoughi, M., Chen, X., Hong, M., & Hu, C. (2019) · Journal of Energy Storage · doi:10.1016/j.est.2019.100817 · Cited by 392
Metadata
- Authors
- Chen, C., Xiong, R., & Shen, W.
- Affiliations
- Beijing Institute of Technology (CN)
- Swinburne University of Technology (AU)
- Venue
- IEEE Transactions on Power Electronics
- Published
- 2018-01
- Volume
- 33
- Issue
- 1
- Pages
- 332-342
- ISSN
- 0885-8993 (ISSN-L)
- 1941-0107
- OpenAlex
- W2588743433
- Cited by
- 295
- References
- 37
- Citations by year
- 2026: 8 · 2025: 34 · 2024: 23 · 2023: 35 · 2022: 38 · 2021: 34 · 2020: 40 · 2019: 31 · 2018: 31
- FWCI
- 21.36
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- IEEE Transactions on Power Electronics (publishedVersion)
- Swinburne figshare (Swinburne University of Technology) (submittedVersion)
- Funders
- National Natural Science Foundation of China (51507012, U1564206)
- Australian Research Council Linkage (LP110200302)
- Sino-Polish Collaborative Research in E-mobility Public Transportation (2015DFG81930)
- Topics
- Physical Sciences › Engineering › Automotive Engineering › Battery Modeling and Management
- Physical Sciences › Engineering › Control and Systems Engineering › Control Systems and Identification
- Physical Sciences › Engineering › Automotive Engineering › Electric and Hybrid Vehicle Technologies
- Keywords
- lithium-ion batteries, state of charge estimation, battery capacity estimation, electric vehicles, dual Kalman filter, robust state estimation, real-time estimation
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.