The DOI matches its Crossref record; 39 of the 39 references it cites were found in a registry or an index.
The Filler Effect: The Influence of Filler Content and Surface Area on Cementitious Reaction Rates
Abstract
Finely ground mineral powders are known to accelerate cement hydration rates. This “filler effect” has been attributed to the effects of dilution (w/c increase) when the cement content is reduced or to the provision of additional surface area by fine powders. The latter contribution (i.e., surface area increase) is speculated to provide additional sites for the nucleation of the hydration products, which accelerates reactions. Through extensive experimentation and simulation this study describes the influence of surface area and mineral type (e.g., quartz or limestone) on cement reaction rates. Simulations using a boundary nucleation and growth ( BNG ) model and a multiphase reaction ensemble ( MRE ) indicate that the extent of the acceleration is linked to the: (1) magnitude of surface area increase and (2a) capacity of the filler's surface to offer favorable nucleation sites for hydration products. Other simulations using a kinetic cellular automaton model (Hydrati CA ) suggest that accelerations are linked to: (2b) the interfacial properties of the filler that alters (increases or decreases) its tendency to serve as a nucleant, and (3) the chemical composition of the filler and the tendency for its dissociated ions to participate in exchange reactions with the calcium silicate hydrate product. The simulations are correlated with accelerations observed using isothermal calorimetry when fillers partially replace cement. The research correlates and unifies the fundamental parameters that drive the filler effect and provides a mechanistic understanding of the influence of filler agents on cementitious reaction rates.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Influence of limestone on the hydration of Portland cements
Lothenbach, B., Le Saout, G., Gallucci, E., & Scrivener, K. (2008) · Cement and Concrete Research · doi:10.1016/j.cemconres.2008.01.002 · Cited by 1,699
Hydration mechanisms of ternary Portland cements containing limestone powder and fly ash
De Weerdt, K., Haha, M. B., Le Saout, G., Kjellsen, K. O., Justnes, H., & Lothenbach, B. (2011) · Cement and Concrete Research · doi:10.1016/j.cemconres.2010.11.014 · Cited by 1,448
Influence of Nucleation Seeding on the Hydration Mechanisms of Tricalcium Silicate and Cement
Thomas, J. J., Jennings, H. M., & Chen, J. J. (2009) · The Journal of Physical Chemistry C · doi:10.1021/jp809811w · Cited by 810
Review: Nucleation in solutions revisited
Kashchiev, D., & van Rosmalen, G. M. (2003) · Crystal Research and Technology · doi:10.1002/crat.200310070 · Cited by 695
Studies on the carboaluminate formation in limestone filler-blended cements
Bonavetti, V. L., Rahhal, V. F., & Irassar, E. F. (2001) · Cement and Concrete Research · doi:10.1016/s0008-8846(01)00491-4 · Cited by 576
Dissolution theory applied to the induction period in alite hydration
Juilland, P., Gallucci, E., Flatt, R., & Scrivener, K. (2010) · Cement and Concrete Research · doi:10.1016/j.cemconres.2010.01.012 · Cited by 537
Crystal Growth for Beginners - Fundamentals of Nucleation, Crystal Growth and Epitaxy
Markov, I. V. (2003) · WORLD SCIENTIFIC eBooks · doi:10.1142/9789812796899 · Cited by 533
Modeling and simulation of cement hydration kinetics and microstructure development
Thomas, J. J., Biernacki, J. J., Bullard, J. W., Bishnoi, S., Dolado, J. S., Scherer, G. W., & Luttge, A. (2011) · Cement and Concrete Research · doi:10.1016/j.cemconres.2010.10.004 · Cited by 489
Self-citationLimestone filler cement in low w/c concrete: A rational use of energy
Bonavetti, V., Donza, H., Menéndez, G., Cabrera, O., & Irassar, E. F. (2003) · Cement and Concrete Research · doi:10.1016/s0008-8846(02)01087-6 · Cited by 462
Influence of finely ground limestone on cement hydration
Péra, J., Husson, S., & Guilhot, B. (1999) · Cement and Concrete Composites · doi:10.1016/s0958-9465(98)00020-1 · Cited by 436
A New Approach to Modeling the Nucleation and Growth Kinetics of Tricalcium Silicate Hydration
Thomas, J. J. (2007) · Journal of the American Ceramic Society · doi:10.1111/j.1551-2916.2007.01858.x · Cited by 348
Hydration of C3A–gypsum systems
Quennoz, A., & Scrivener, K. L. (2012) · Cement and Concrete Research · doi:10.1016/j.cemconres.2012.04.005 · Cited by 327
Filler cement: The effect of the secondary component on the hydration of Portland cement
Gutteridge, W. A., & Dalziel, J. A. (1990) · Cement and Concrete Research · doi:10.1016/0008-8846(90)90046-z · Cited by 282
Filler cement: The effect of the secondary component on the hydration of Portland cement
Gutteridge, W. A., & Dalziel, J. A. (1990) · Cement and Concrete Research · doi:10.1016/0008-8846(90)90011-l · Cited by 278
Modeling the influence of limestone filler on cement hydration using CEMHYD3D
Bentz, D. P. (2006) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2005.10.006 · Cited by 243
Carboaluminate Phases Formation During the Hydration of Calcite‐Containing Portland Cement
Ipavec, A., Gabrovšek, R., Vuk, T., Kaučič, V., Maček, J., & Meden, A. (2011) · Journal of the American Ceramic Society · doi:10.1111/j.1551-2916.2010.04201.x · Cited by 243
Studying nucleation and growth kinetics of alite hydration using μic
Bishnoi, S., & Scrivener, K. L. (2009) · Cement and Concrete Research · doi:10.1016/j.cemconres.2009.07.004 · Cited by 219
Fine limestone additions to regulate setting in high volume fly ash mixtures
Bentz, D. P., Sato, T., de la Varga, I., & Weiss, W. J. (2012) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2011.09.004 · Cited by 215
Seeding Effect of Nano-CaCO3 on the Hydration of Tricalcium Silicate
Sato, T., & Diallo, F. (2010) · Transportation Research Record: Journal of the Transportation Research Board · doi:10.3141/2141-11 · Cited by 209
Rheology and setting of high volume fly ash mixtures
Bentz, D. P., & Ferraris, C. F. (2010) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2010.01.008 · Cited by 164
The influence of sodium and potassium hydroxide on alite hydration: Experiments and simulations
Kumar, A., Sant, G., Patapy, C., Gianocca, C., & Scrivener, K. L. (2012) · Cement and Concrete Research · doi:10.1016/j.cemconres.2012.07.003 · Cited by 155
Self-citationEarly-Age Properties of Cement-Based Materials. II: Influence of Water-to-Cement Ratio
Bentz, D. P., Peltz, M. A., & Winpigler, J. A. (2009) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)0899-1561(2009)21:9(512 · Cited by 155
Bullard, J. W. (2008) · Journal of the American Ceramic Society · doi:10.1111/j.1551-2916.2008.02419.x · Cited by 153
Self-citationThomas, J. J., Allen, A. J., & Jennings, H. M. (2009) · The Journal of Physical Chemistry C · doi:10.1021/jp907078u · Cited by 150
Why alite stops hydrating below 80% relative humidity
Flatt, R. J., Scherer, G. W., & Bullard, J. W. (2011) · Cement and Concrete Research · doi:10.1016/j.cemconres.2011.06.001 · Cited by 146
Self-citationEarly hydration of portland cement with crystalline mineral additions
Rahhal, V. F., & Talero, R. (2005) · Cement and Concrete Research · doi:10.1016/j.cemconres.2004.12.001 · Cited by 132
Modelling early age hydration kinetics of alite
Kumar, A., Bishnoi, S., & Scrivener, K. L. (2012) · Cement and Concrete Research · doi:10.1016/j.cemconres.2012.03.003 · Cited by 131
Self-citationBullard, J. W., & Flatt, R. J. (2010) · Journal of the American Ceramic Society · doi:10.1111/j.1551-2916.2010.03656.x · Cited by 129
Self-citationShape analysis of a reference cement
Garboczi, E. J., & Bullard, J. W. (2004) · Cement and Concrete Research · doi:10.1016/j.cemconres.2004.01.006 · Cited by 128
Self-citationKumar, A., Oey, T., Kim, S., Thomas, D., Badran, S., Li, J., Fernandes, F., Neithalath, N., & Sant, G. (2013) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2013.05.002 · Cited by 112
Self-citationInfluence of mineral additives on the hydration characteristics of ordinary Portland cement
Sharma, R., & Pandey, S. P. (1999) · Cement and Concrete Research · doi:10.1016/s0008-8846(99)00104-0 · Cited by 111
Kirby, D. M., & Biernacki, J. J. (2012) · Cement and Concrete Research · doi:10.1016/j.cemconres.2012.05.009 · Cited by 94
Peterson, V. K., & Juenger, M. C. G. (2006) · Chemistry of Materials · doi:10.1021/cm061724y · Cited by 93
Jayapalan, A. R., Lee, B. Y., Fredrich, S. M., & Kurtis, K. E. (2010) · Transportation Research Record Journal of the Transportation Research Board · doi:10.3141/2141-08 · Cited by 92
Effects of D2O and Mixing on the Early Hydration Kinetics of Tricalcium Silicate
Thomas, J. J., & Jennings, H. M. (1999) · Chemistry of Materials · doi:10.1021/cm9900857 · Cited by 87
A three-dimensional microstructural model of reactions and transport in aqueous mineral systems
Bullard, J. W. (2007) · Modelling and Simulation in Materials Science and Engineering · doi:10.1088/0965-0393/15/7/002 · Cited by 85
Self-citationCellular automation model of reaction-transport porcesses
Karapiperis, T., & Blankleider, B. (1994) · Physica D Nonlinear Phenomena · doi:10.1016/0167-2789(94)00093-x · Cited by 56
Modelling excess surface energy in dry and wetted calcite systems
Kvamme, B., Kuznetsova, T. V., & Uppstad, D. (2009) · Journal of Mathematical Chemistry · doi:10.1007/s10910-009-9548-y · Cited by 32
Optimum sulfate content of Portland cement
Škapa, R. (2009) · Cited by 15
Cited by
Recent advances in understanding the role of supplementary cementitious materials in concrete
Juenger, M. C. G., & Siddique, R. (2015) · Cement and Concrete Research · doi:10.1016/j.cemconres.2015.03.018 · Cited by 1,229
Reactivity of supplementary cementitious materials (SCMs) in cement blends
Skibsted, J., & Snellings, R. (2019) · Cement and Concrete Research · doi:10.1016/j.cemconres.2019.105799 · Cited by 984
Understanding the Filler Effect on the Nucleation and Growth of C‐S‐H
Berodier, E., & Scrivener, K. (2014) · Journal of the American Ceramic Society · doi:10.1111/jace.13177 · Cited by 882
Yang, T., Zhu, H., Zhang, Z., Gao, X., Zhang, C., & Wu, Q. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.04.008 · Cited by 399
The use of rice husk ash as reactive filler in ultra-high performance concrete
Kang, S.-H., Hong, S.-G., & Moon, J. (2019) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.09.004 · Cited by 359
Metadata
- Authors
- Oey, T., Kumar, A., Bullard, J. W., Neithalath, N., & Sant, G.
- Venue
- Journal of the American Ceramic Society
- Publisher
- Wiley
- Published
- 2013-03-15
- Volume
- 96
- Issue
- 6
- Pages
- 1978-1990
- ISSN
- 0002-7820 (ISSN-L)
- 1551-2916
- OpenAlex
- W2072342051
- Cited by
- 490
- References
- 39
- FWCI
- 34.09
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.