The DOI matches its Crossref record.
On the Catastrophic Shear Instability in High-Speed Machining of an AISI 4340 Steel
Abstract
An AISI 4340 Steel (325 BHN) was machined at various speeds up to 2500 m/min (8000 SFPM). Longitudinal midsections of the chips were examined metallurgically to delineate the differences in the chip formation characteristics at various speeds. Chips were found to be continuous at 30 to 60 m/min (100 to 200 SFPM) but discontinuous below this speed. Instabilities in the cutting process, leading to different types of cyclic chip formations, were observed at cutting speeds above 60 m/min (200 SFPM). Fully developed catastrophic shear bands separated by large areas (segments) of relatively less deformed material, similar to that when machining titanium alloys, were observed in the chips at cutting speeds above 275 m/min (800 SFPM). The intense shear bands between the segments appeared to have formed subsequent to the localized intense deformation of the segment in the primary shear zone. As the cutting speed increases, the extent of contact between the segments is found to decrease rapidly. At speeds of 1000 m/min (3200 SFPM) and above, due to rapid intense, localized shear between the segments, these segments were found to separate completely as isolated segments instead of being held intact as a long chip. The speed at which this decohesion occurs was found to depend upon the metallurgical state of the steel machined and its hardness. As in the case of machining titanium alloys, the deformation of the chip as it slides on the tool face, i.e., “secondary shear zone,” appeared to be negligible when machining this AISI 4340 steel at high speed. Based on the metallurgical study of the chip and the similarities of machining this material at high speed and that of titanium alloys at normal speed, a cyclic phenomenon in the primary shear zone is identified as the source of instability responsible for the large-scale heterogeneity and a mechanism of chip formation when machining AISI 4340 steel at high speed is proposed.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Mechanics of Saw-Tooth Chip Formation in Metal Cutting
Vyas, A., & Shaw, M. C. (1999) · Journal of Manufacturing Science and Engineering · doi:10.1115/1.2831200 · Cited by 301
Observations on chip formation and acoustic emission in machining Ti–6Al–4V alloy
Barry, J., Byrne, G., & Lennon, D. (2001) · International Journal of Machine Tools and Manufacture · doi:10.1016/s0890-6955(00)00096-1 · Cited by 265
Wear behavior in turning high hardness alloy steel by CBN tool
Lin, H. M., Liao, Y. S., & Wei, C. C. (2008) · Wear · doi:10.1016/j.wear.2007.06.006 · Cited by 94
Hassan, A., Khan, M. A., Younas, M., Jaffery, S. H. I., Khan, M., Ahmed, N., & Awang, M. (2024) · International Journal of Automotive and Mechanical Engineering · doi:10.15282/ijame.21.2.2024.11.0874 · Cited by 4
Metadata
- Authors
- Komanduri, R., Schroeder, T., Hazra, J., von Turkovich, B. F., & Flom, D. G.
- Venue
- Journal of Engineering for Industry
- Publisher
- ASME International
- Published
- 1982-05-01
- Volume
- 104
- Issue
- 2
- Pages
- 121-131
- ISSN
- 0022-0817 (ISSN-L)
- OpenAlex
- W1998045435
- Cited by
- 194
- References
- 0
- FWCI
- 8.31
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: On the Catastrophic Shear Instability in High-Speed Machining of an AISI 4340 Steel. https://app.cochat.ai/papers/10.1115/1.3185807
- The paper
- Komanduri, R., Schroeder, T., Hazra, J., von Turkovich, B. F., & Flom, D. G. (1982). On the Catastrophic Shear Instability in High-Speed Machining of an AISI 4340 Steel. Journal of Engineering for Industry. https://doi.org/10.1115/1.3185807
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.