The DOI matches its Crossref record; 6 of the 6 references it cites were found in a registry or an index.
Mechanics of Saw-Tooth Chip Formation in Metal Cutting
Abstract
The saw-tooth chip was the last of the major types to be identified. This occurred in 1954 during machining studies of titanium alloys which were then being considered for aerospace applications because of their large strength-to-weight ratio and corrosion resistance. This is a type of chip that forms when very hard brittle materials are machined at high speeds and feeds. Since this is an area of machining which will be of increasing interest in the future, particularly in hard turning, it is important that the mechanism and mechanics of this type of chip formation be better understood. At present, there are two theories concerning the basic origin of saw-tooth chips. The first to appear assumed they are of thermal origin while the second assumes they arise due to the periodic development of cracks in the original surface of the work. The thesis presented here is that the root cause for saw-tooth chip formations is cyclic cracking. This is followed by a discussion of extensive experimental data that supports this point of view.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
(1987) · Journal of Mechanical Working Technology · doi:10.1016/0378-3804(87)90039-8 · Cited by 2,107
Mechanics of the Metal Cutting Process. II. Plasticity Conditions in Orthogonal Cutting
Merchant, M. E. (1945) · Journal of Applied Physics · doi:10.1063/1.1707596 · Cited by 768
On Chip Morphology, Tool Wear and Cutting Mechanics in Finish Hard Turning
Davies, M. A., Chou, Y., & Evans, C. J. (1996) · CIRP Annals · doi:10.1016/s0007-8506(07)63020-0 · Cited by 214
On the Catastrophic Shear Instability in High-Speed Machining of an AISI 4340 Steel
Komanduri, R., Schroeder, T., Hazra, J., von Turkovich, B. F., & Flom, D. G. (1982) · Journal of Engineering for Industry · doi:10.1115/1.3185807 · Cited by 194
A Model for Chip Formation During Machining of Hardened Steel
Elbestawi, M. A., Srivastava, A. K., & El-Wardany, T. I. (1996) · CIRP Annals · doi:10.1016/s0007-8506(07)63019-4 · Cited by 129
On the Dynamics of Chip Formation in Machining Hard Metals
Davies, M. A., Burns, T. J., & Evans, C. J. (1997) · CIRP Annals · doi:10.1016/s0007-8506(07)60768-9 · Cited by 110
Cited by
Calamaz, M., Coupard, D., & Girot, F. (2008) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2007.10.014 · Cited by 622
Tönshoff, H. K., Arendt, C., & Amor, R. B. (2000) · CIRP Annals · doi:10.1016/s0007-8506(07)63455-6 · Cited by 519
Characteristics of cutting forces and chip formation in machining of titanium alloys
Sun, S., Brandt, M., & Dargusch, M. S. (2009) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2009.02.008 · Cited by 485
Sima, M., & Özel, T. (2010) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2010.08.004 · Cited by 477
Problems and solutions in machining of titanium alloys
Pramanik, A. (2014) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-013-5326-x · Cited by 382
Metadata
- Authors
- Vyas, A., & Shaw, M. C.
- Venue
- Journal of Manufacturing Science and Engineering
- Publisher
- ASME International
- Published
- 1999-05-01
- Volume
- 121
- Issue
- 2
- Pages
- 163-172
- ISSN
- 1087-1357 (ISSN-L)
- 1528-8935
- OpenAlex
- W2006696369
- Cited by
- 301
- References
- 6
- FWCI
- 23.61
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Mechanics of Saw-Tooth Chip Formation in Metal Cutting. https://app.cochat.ai/papers/10.1115/1.2831200
- The paper
- Vyas, A., & Shaw, M. C. (1999). Mechanics of Saw-Tooth Chip Formation in Metal Cutting. Journal of Manufacturing Science and Engineering. https://doi.org/10.1115/1.2831200
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.