The DOI matches its Crossref record.
The Influence of Processing Parameters on the Mechanical Properties of Selectively Laser Melted Stainless Steel Microlattice Structures
Abstract
The rapid manufacturing process of selective laser melting has been used to produce a series of stainless steel 316L microlattice structures. Laser power and laser exposure time are the two processing parameters used for manufacturing the lattice structures and, therefore, control the quality and mechanical properties of microlattice parts. An evaluation of the lattice material was undertaken by manufacturing a range of struts, representative of the individual trusses of the microlattices, as well as, microlattice block structures. Low laser powers were shown to result in significantly lower strand strengths due to the presence of inclusions of unmelted powder in the strut cross-sections. Higher laser powers resulted in struts that were near to full density as the measured strengths were comparable to the bulk 316L values. Uniaxial compression tests on microlattice blocks highlighted the effect of manufacturing parameters on the mechanical properties of these structures and a linear relationship was found between the plateau stress and elastic modulus relative to the measured relative density.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Laser additive manufacturing of metallic components: materials, processes and mechanisms
Gu, D. D., Meiners, W., Wissenbach, K., & Poprawe, R. (2012) · International Materials Reviews · doi:10.1179/1743280411y.0000000014 · Cited by 3,197
SLM lattice structures: Properties, performance, applications and challenges
Maconachie, T., Leary, M., Lozanovski, B., Zhang, X., Qian, M., Faruque, O., & Brandt, M. (2019) · Materials & Design · doi:10.1016/j.matdes.2019.108137 · Cited by 1,497
Benedetti, M., du Plessis, A., Ritchie, R. O., Dallago, M., Razavi, N., & Berto, F. (2021) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2021.100606 · Cited by 788
Additive manufacturing of 3D nano-architected metals
Vyatskikh, A., Delalande, S., Kudo, A., Zhang, X., Portela, C. M., & Greer, J. R. (2018) · Nature Communications · doi:10.1038/s41467-018-03071-9 · Cited by 593
Compressive behaviour of stainless steel micro-lattice structures
Gümrük, R., & Mines, R. A. W. (2013) · International Journal of Mechanical Sciences · doi:10.1016/j.ijmecsci.2013.01.006 · Cited by 445
Self-citation
Metadata
- Authors
- Tsopanos, S., Mines, R. A. W., McKown, S., Shen, Y., Cantwell, W. J., Brooks, W., & Sutcliffe, C. J.
- Venue
- Journal of Manufacturing Science and Engineering
- Publisher
- ASME International
- Published
- 2010-07-23
- Volume
- 132
- Issue
- 4
- ISSN
- 1087-1357 (ISSN-L)
- 1528-8935
- OpenAlex
- W2094464691
- Cited by
- 252
- References
- 0
- FWCI
- 10.95
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: The Influence of Processing Parameters on the Mechanical Properties of Selectively Laser Melted Stainless Steel Microlattice Structures. https://app.cochat.ai/papers/10.1115/1.4001743
- The paper
- Tsopanos, S., Mines, R. A. W., McKown, S., Shen, Y., Cantwell, W. J., Brooks, W., & Sutcliffe, C. J. (2010). The Influence of Processing Parameters on the Mechanical Properties of Selectively Laser Melted Stainless Steel Microlattice Structures. Journal of Manufacturing Science and Engineering. https://doi.org/10.1115/1.4001743
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.