Polyethylene materials with in-chain ketones from nonalternating catalytic copolymerization
Open accessPublished version of a preprint
The DOI matches its Crossref record; 47 of the 47 references it cites were found in a registry or an index; 1 of the 8 sources its claims cite were checked for support.
Abstract
Polyethylene with a nickel’s worth of CO: The biggest problem with polyethylene, the most abundantly manufactured plastic, is that it doesn’t break down easily once it is discarded. Chemists have long sought to introduce small quantities of carbon monoxide (CO) into polyethylene chains to promote photodegradation, but too much CO tends to jump in and spoil the plastic’s other properties. Baur et al . report that nickel catalysts coordinated by bulky phosphinophenolate ligands can catalyze ethylene polymerization with approximately 1% CO incorporation, preserving tensile strength while promoting degradation under ultraviolet exposure (see the Perspective by Sobkowicz). —JSY
Overview
CoChat Summary
TL;DR
Neutral Ni(II) phosphinophenolate catalysts enable non-alternating copolymerization of ethylene and CO, placing isolated in-chain keto groups into high molecular weight polyethylene while retaining HDPE-like crystallinity and tensile properties. The resulting keto-modified polyethylenes are melt-processable and may offer a route to less environmentally persistent polyolefins.
Key findings
- Non-alternating ethylene/CO copolymerization was achieved with Ni(II) catalysts 2–7; at low CO incorporation, keto groups are mostly isolated or non-alternating rather than alternating. For example, entry 4 gave 0.3 mol% CO incorporation, I/NA/A = 79/21/0, Mn = 140 × 10³ g mol⁻¹, Mw/Mn = 1.6, and Tm = 134 °C (68% crystallinity); entry 10 gave 0.6 mol% CO by IR (1.4 mol% by ¹³C NMR), I/NA/A = 27/33/39, Mn = 154 × 10³ g mol⁻¹, and Tm = 134 °C.
- The keto-modified polyethylenes reached high molecular weights up to Mw ~400,000 g mol⁻¹ and Mn ~220,000 g mol⁻¹, in contrast to prior ethylene–CO copolymerizations that yielded low molecular weight brittle waxes with Mn ≤ 3,000 g mol⁻¹.
- HDPE materials properties were retained: WAXS diffractograms were virtually identical to HDPE, melting/crystallization points were virtually unaltered, and injection-molded test bars showed ductile tensile behavior comparable to commercial HDPE. Reported tensile values were E = 995 MPa and σy = 29 MPa, compared with literature HDPE E = 900 MPa and σy = 27 MPa, and LDPE E = 240 MPa and σy = 12 MPa.
- CO appeared to suppress chain transfer and branching: endgroup analysis showed only olefinic endgroups also found in homopolyethylenes, and copolymers showed complete absence of branches compared with ethylene homopolymers; catalysts were stable for hours in CO copolymerizations.
Methods
- Polymerization experiments screened neutral Ni(II) catalyst precursors: salicylaldiminato 1 and phosphinophenolato complexes 2–8 with bulky substituents. Table 1 conditions were typically 10 µmol precatalyst, 100 mL toluene, 500 rpm, 50–120 °C, 5–40 bar ethylene, CO in feed 0.2–2.6 mol%, and 10–240 min; selected entries used 5 µmol precatalyst, 200 mL toluene, and 0.05 atm CO introduced before ethylene.
- Microstructure was analyzed by ¹³C NMR using ¹³CO copolymers, with 1D and 2D NMR and IR spectroscopy; CO incorporation was determined by IR and by ¹³C NMR. Molecular weights were measured by GPC in 1,2-dichlorobenzene at 160 °C via universal calibration against polystyrene standards; thermal data by DSC second heating; solid-state structure by WAXS; mechanical properties by tensile tests on injection-molded bars.
- Mechanistic features were probed by comparing polymer composition and yield over time, comparing copolymerization with ethylene homopolymerization, and analyzing polymer endgroups.
Limitations
- The paper does not include a dedicated Limitations section. Stated limitations include: copolymerization yields and average activities were lowered compared with ethylene homopolymerization; efficient copolymerization with catalyst 2 required ca. 100 °C; higher polymerization temperatures decreased CO incorporation and were necessary to achieve non-alternation; catalyst 1 had limited temperature stability and formed only alternating polyketone even at elevated temperature.
- Evident from the data: non-alternating products were obtained only at high E/CO ratios on the order of 100 and generally low CO feed (many useful entries at 0.2–0.6 mol% CO in feed); higher CO feed often gave alternating polyketone or very low yields. Several catalyst precursors (e.g., 1, 3, 4, 6, 8 under tested conditions) gave alternating polyketone or negligible activity.
- The paper presents perspectives for photolytic and oxidative chain breakdown but does not report degradation or long-term environmental persistence data for these specific materials.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures



Verification
Claims the paper makes
0 Valid · 2 Not valid · 5 Not checked · 28 Own results and interpretations
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“At given initial reaction conditions, the composition of the formed polymer does not vary significantly with increasing reaction time and increasing polymer yield (entries 2 to 4 and 10 to 12).”
§ Cat.T [°C] p [bar] t [min] CO in feed [mol%] b yield [g] TOF c χ d [mol%] I / NA / A e [mol-%] M n f [10 3 g mol -1 ] M w /M n f T m [°C] (% Cryst) g 1 1 50 10 60 0.2 0.06 0.2 50 h 0 / 0 / 100 h n.d.h n.d.h 243 i 2 2 100 5 10 0.2 0.80 15.6 0.3 (0.4) 69 / 11 / 20 54 1.7 133 (71) 3 2 100 5 60 0.2 2.07 7.41 0.3 (0.4) 70 / 22 / 8 102 1.5 135 (66) 4 2 100 5 120 0.2 4.26 7.61 0.3 (0.3) 79 / 21 / 0 140 1.6 134 (68) 5 2 110 5 60 0.2 1.07 3.81 0.5 (0.5) 61 / 27 / 12 84 1.7 133 (65) 6 2 120 5 30 0.2 0.06 0.41 1.7 (1.7) 31 / 49 / 20 3 8.9 110 (65) 7 2 100 40 10 0.2 1.20 23.4 1.1 (2.7) 9 / 37 / 54 42 2.9 133 (68) 8 2 70 40 90 0.2 0.05 0.12 50 h 0 / 0 / 100 h n.d.h n.d.h 228 i 9 2 100 5 120 0.6 1.98 3.53 0.8 (1.1) 32 / 36 / 32 147 1.8 135 (62) 10 2 100 10 60 0.6 2.35 8.39 0.6 (1.4) 27 / 33 / 39 154 1.9 134 (63) 11 2 100 10 120 0.6 3.01 5.38 0.6 (1.3) 27 / 27 / 46 210 1.8 138 (61) 12 2 100 10 240 0.6 3.31 2.95 0.6 (1.0) 43 / 33 / 24 216 1.8 136 (60) 13 2 100 5 120 2.6 0.06 0.08 50 h 0 / 0 / 100 h n.d.h n.d.h 230 i 14 5 100 5 120 2.6 0.03 0.06 50 h 0 / 0 / 100 h n.d.h n.d.h 228 i 15 5 100 5 60 0.2 1.04 3.73 0.4 (0.4) 62 / 29 / 9 88 1.6 133 (70) 16 3 100 5 120 0.6 0.05 0.08 50 h 0 / 0 / 100 h n.d.h n.d.h 229 i 17 4 100 5 120 0.6 1.13 2.02 1.0 (1.4) 21 / 29 / 49 60 1.7 133 (69) 18 5 100 5 120 0.6 0.26 0.46 3.7 (4.4) 28 / 34 / 38 84 1.7 134 (63) 19 6 100 5 120 0.6 0.44 0.79 1.6 (3.0) 7 / 34 / 59 45 1.6 133 (69) 20 7 100 5 120 0.6 0.82 1.47 1.1 (2.5) 18 / 33 /49 90 1.7 135 (67) 21 8 100 5 120 0.6 0.01 0.02 50 h 0 / 0 / 100 h n.d.h n.d.h 232 i 22 1 90 40 60 0.1 m 0.05 0.2 50 h 0 / 0 / 100 h n.d.h n.d.h 240 i 23 k 2 100 5 20 -10.8 231.2 --17 1.9 131 (71) 24 k 2 70 10 10 -3.16 135.1 --548 2.3 138 (58) > Mechanistic features of the catalytic polymerization.
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Also, melting and crystallization points are virtually unaltered (Fig. 3c).”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Catalysts are stable for hours in CO copolymerizations (entries 2 to 4).”
§ Cat.T [°C] p [bar] t [min] CO in feed [mol%] b yield [g] TOF c χ d [mol%] I / NA / A e [mol-%] M n f [10 3 g mol -1 ] M w /M n f T m [°C] (% Cryst) g 1 1 50 10 60 0.2 0.06 0.2 50 h 0 / 0 / 100 h n.d.h n.d.h 243 i 2 2 100 5 10 0.2 0.80 15.6 0.3 (0.4) 69 / 11 / 20 54 1.7 133 (71) 3 2 100 5 60 0.2 2.07 7.41 0.3 (0.4) 70 / 22 / 8 102 1.5 135 (66) 4 2 100 5 120 0.2 4.26 7.61 0.3 (0.3) 79 / 21 / 0 140 1.6 134 (68) 5 2 110 5 60 0.2 1.07 3.81 0.5 (0.5) 61 / 27 / 12 84 1.7 133 (65) 6 2 120 5 30 0.2 0.06 0.41 1.7 (1.7) 31 / 49 / 20 3 8.9 110 (65) 7 2 100 40 10 0.2 1.20 23.4 1.1 (2.7) 9 / 37 / 54 42 2.9 133 (68) 8 2 70 40 90 0.2 0.05 0.12 50 h 0 / 0 / 100 h n.d.h n.d.h 228 i 9 2 100 5 120 0.6 1.98 3.53 0.8 (1.1) 32 / 36 / 32 147 1.8 135 (62) 10 2 100 10 60 0.6 2.35 8.39 0.6 (1.4) 27 / 33 / 39 154 1.9 134 (63) 11 2 100 10 120 0.6 3.01 5.38 0.6 (1.3) 27 / 27 / 46 210 1.8 138 (61) 12 2 100 10 240 0.6 3.31 2.95 0.6 (1.0) 43 / 33 / 24 216 1.8 136 (60) 13 2 100 5 120 2.6 0.06 0.08 50 h 0 / 0 / 100 h n.d.h n.d.h 230 i 14 5 100 5 120 2.6 0.03 0.06 50 h 0 / 0 / 100 h n.d.h n.d.h 228 i 15 5 100 5 60 0.2 1.04 3.73 0.4 (0.4) 62 / 29 / 9 88 1.6 133 (70) 16 3 100 5 120 0.6 0.05 0.08 50 h 0 / 0 / 100 h n.d.h n.d.h 229 i 17 4 100 5 120 0.6 1.13 2.02 1.0 (1.4) 21 / 29 / 49 60 1.7 133 (69) 18 5 100 5 120 0.6 0.26 0.46 3.7 (4.4) 28 / 34 / 38 84 1.7 134 (63) 19 6 100 5 120 0.6 0.44 0.79 1.6 (3.0) 7 / 34 / 59 45 1.6 133 (69) 20 7 100 5 120 0.6 0.82 1.47 1.1 (2.5) 18 / 33 /49 90 1.7 135 (67) 21 8 100 5 120 0.6 0.01 0.02 50 h 0 / 0 / 100 h n.d.h n.d.h 232 i 22 1 90 40 60 0.1 m 0.05 0.2 50 h 0 / 0 / 100 h n.d.h n.d.h 240 i 23 k 2 100 5 20 -10.8 231.2 --17 1.9 131 (71) 24 k 2 70 10 10 -3.16 135.1 --548 2.3 138 (58) > Mechanistic features of the catalytic polymerization.
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Indeed, tensile tests on injection molded test bars show a ductile behavior that compares to commercial HDPE (Fig. 3d).”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“We report how the long-sought non-alternating catalytic copolymerization of ethylene and CO can be achieved with Ni(II) catalysts.”
§ Polyethylene Materials with In-Chain Ketones from Catalytic Copolymerization > Introduction
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
13 more claims
Create a free account to see all 35 claims and every source verdict.
- It may state two separate claims as one. 16
- Probably not a substantial claim. 2
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“Insertion of ketones into PE through the copolymerization of ethylene with carbon monoxide results in photodegradable PE derivatives that can break down to smaller fragments but falls short of creating a circular plastics lifecycle”
From Chemically recyclable polyolefin-like multiblock polymers (2023) · cites this paper as [18]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ Cat.T [°C] p [bar] t [min] CO in feed [mol%] b yield [g] TOF c χ d [mol%] I / NA / A e [mol-%] M n f [10 3 g mol -1 ] M w /M n f T m [°C] (% Cryst) g 1 1 50 10 60 0.2 0.06 0.2 50 h 0 / 0 / 100 h n.d.h n.d.h 243 i 2 2 100 5 10 0.2 0.80 15.6 0.3 (0.4) 69 / 11 / 20 54 1.7 133 (71) 3 2 100 5 60 0.2 2.07 7.41 0.3 (0.4) 70 / 22 / 8 102 1.5 135 (66) 4 2 100 5 120 0.2 4.26 7.61 0.3 (0.3) 79 / 21 / 0 140 1.6 134 (68) 5 2 110 5 60 0.2 1.07 3.81 0.5 (0.5) 61 / 27 / 12 84 1.7 133 (65) 6 2 120 5 30 0.2 0.06 0.41 1.7 (1.7) 31 / 49 / 20 3 8.9 110 (65) 7 2 100 40 10 0.2 1.20 23.4 1.1 (2.7) 9 / 37 / 54 42 2.9 133 (68) 8 2 70 40 90 0.2 0.05 0.12 50 h 0 / 0 / 100 h n.d.h n.d.h 228 i 9 2 100 5 120 0.6 1.98 3.53 0.8 (1.1) 32 / 36 / 32 147 1.8 135 (62) 10 2 100 10 60 0.6 2.35 8.39 0.6 (1.4) 27 / 33 / 39 154 1.9 134 (63) 11 2 100 10 120 0.6 3.01 5.38 0.6 (1.3) 27 / 27 / 46 210 1.8 138 (61) 12 2 100 10 240 0.6 3.31 2.95 0.6 (1.0) 43 / 33 / 24 216 1.8 136 (60) 13 2 100 5 120 2.6 0.06 0.08 50 h 0 / 0 / 100 h n.d.h n.d.h 230 i 14 5 100 5 120 2.6 0.03 0.06 50 h 0 / 0 / 100 h n.d.h n.d.h 228 i 15 5 100 5 60 0.2 1.04 3.73 0.4 (0.4) 62 / 29 / 9 88 1.6 133 (70) 16 3 100 5 120 0.6 0.05 0.08 50 h 0 / 0 / 100 h n.d.h n.d.h 229 i 17 4 100 5 120 0.6 1.13 2.02 1.0 (1.4) 21 / 29 / 49 60 1.7 133 (69) 18 5 100 5 120 0.6 0.26 0.46 3.7 (4.4) 28 / 34 / 38 84 1.7 134 (63) 19 6 100 5 120 0.6 0.44 0.79 1.6 (3.0) 7 / 34 / 59 45 1.6 133 (69) 20 7 100 5 120 0.6 0.82 1.47 1.1 (2.5) 18 / 33 /49 90 1.7 135 (67) 21 8 100 5 120 0.6 0.01 0.02 50 h 0 / 0 / 100 h n.d.h n.d.h 232 i 22 1 90 40 60 0.1 m 0.05 0.2 50 h 0 / 0 / 100 h n.d.h n.d.h 240 i 23 k 2 100 5 20 -10.8 231.2 --17 1.9 131 (71) 24 k 2 70 10 10 -3.16 135.1 --548 2.3 138 (58)
“at desirable values of the CO incorporation of ca. 1 %, the majority of keto groups are not alternating, and moreover amongst these the isolated keto groups prevail.”
§ Cat.T [°C] p [bar] t [min] CO in feed [mol%] b yield [g] TOF c χ d [mol%] I / NA / A e [mol-%] M n f [10 3 g mol -1 ] M w /M n f T m [°C] (% Cryst) g 1 1 50 10 60 0.2 0.06 0.2 50 h 0 / 0 / 100 h n.d.h n.d.h 243 i 2 2 100 5 10 0.2 0.80 15.6 0.3 (0.4) 69 / 11 / 20 54 1.7 133 (71) 3 2 100 5 60 0.2 2.07 7.41 0.3 (0.4) 70 / 22 / 8 102 1.5 135 (66) 4 2 100 5 120 0.2 4.26 7.61 0.3 (0.3) 79 / 21 / 0 140 1.6 134 (68) 5 2 110 5 60 0.2 1.07 3.81 0.5 (0.5) 61 / 27 / 12 84 1.7 133 (65) 6 2 120 5 30 0.2 0.06 0.41 1.7 (1.7) 31 / 49 / 20 3 8.9 110 (65) 7 2 100 40 10 0.2 1.20 23.4 1.1 (2.7) 9 / 37 / 54 42 2.9 133 (68) 8 2 70 40 90 0.2 0.05 0.12 50 h 0 / 0 / 100 h n.d.h n.d.h 228 i 9 2 100 5 120 0.6 1.98 3.53 0.8 (1.1) 32 / 36 / 32 147 1.8 135 (62) 10 2 100 10 60 0.6 2.35 8.39 0.6 (1.4) 27 / 33 / 39 154 1.9 134 (63) 11 2 100 10 120 0.6 3.01 5.38 0.6 (1.3) 27 / 27 / 46 210 1.8 138 (61) 12 2 100 10 240 0.6 3.31 2.95 0.6 (1.0) 43 / 33 / 24 216 1.8 136 (60) 13 2 100 5 120 2.6 0.06 0.08 50 h 0 / 0 / 100 h n.d.h n.d.h 230 i 14 5 100 5 120 2.6 0.03 0.06 50 h 0 / 0 / 100 h n.d.h n.d.h 228 i 15 5 100 5 60 0.2 1.04 3.73 0.4 (0.4) 62 / 29 / 9 88 1.6 133 (70) 16 3 100 5 120 0.6 0.05 0.08 50 h 0 / 0 / 100 h n.d.h n.d.h 229 i 17 4 100 5 120 0.6 1.13 2.02 1.0 (1.4) 21 / 29 / 49 60 1.7 133 (69) 18 5 100 5 120 0.6 0.26 0.46 3.7 (4.4) 28 / 34 / 38 84 1.7 134 (63) 19 6 100 5 120 0.6 0.44 0.79 1.6 (3.0) 7 / 34 / 59 45 1.6 133 (69) 20 7 100 5 120 0.6 0.82 1.47 1.1 (2.5) 18 / 33 /49 90 1.7 135 (67) 21 8 100 5 120 0.6 0.01 0.02 50 h 0 / 0 / 100 h n.d.h n.d.h 232 i 22 1 90 40 60 0.1 m 0.05 0.2 50 h 0 / 0 / 100 h n.d.h n.d.h 240 i 23 k 2 100 5 20 -10.8 231.2 --17 1.9 131 (71) 24 k 2 70 10 10 -3.16 135.1 --548 2.3 138 (58)
“9 2 100 5 120 0.6 1.98 3.53 0.8 (1.1) 32 / 36 / 32 147 1.8 135 (62)”
Citations
Cites
Palladium-Catalyzed Alternating Copolymerization of Alkenes and Carbon Monoxide
Drent, E., & Budzelaar, P. H. M. (1996) · Chemical Reviews · doi:10.1021/cr940282j · Cited by 974
Coordination−Insertion Copolymerization of Fundamental Polar Monomers
Nakamura, A., Ito, S., & Nozaki, K. (2009) · Chemical Reviews · doi:10.1021/cr900079r · Cited by 907
From Multisite Polymerization Catalysis to Sustainable Materials and All-Polyolefin Composites
Stürzel, M., Mihan, S., & Mülhaupt, R. (2016) · Chemical Reviews · doi:10.1021/acs.chemrev.5b00310 · Cited by 822
Drent, E., Van Broekhoven, J. A. M., & Doyle, M. J. (1991) · Journal of Organometallic Chemistry · doi:10.1016/0022-328x(91)80176-k · Cited by 528
The physics of polymers: concepts for understanding their structures and behavior
(1997) · Choice Reviews Online · doi:10.5860/choice.34-2811 · Cited by 434
Keim, W. (2013) · Angewandte Chemie International Edition · doi:10.1002/anie.201305308 · Cited by 426
Novel Coordination of (Benzoylmethylene)triphenylphosphorane in a Nickel Oligomerization Catalyst
Keim, W., Kowaldt, F. H., Goddard, R., & Krüger, C. (1978) · Angewandte Chemie International Edition in English · doi:10.1002/anie.197804661 · Cited by 422
Exploring Ethylene/Polar Vinyl Monomer Copolymerizations Using Ni and Pd α-Diimine Catalysts
Chen, Z., & Brookhart, M. (2018) · Accounts of Chemical Research · doi:10.1021/acs.accounts.8b00225 · Cited by 405
Emerging Palladium and Nickel Catalysts for Copolymerization of Olefins with Polar Monomers
Tan, C., & Chen, C. (2019) · Angewandte Chemie International Edition · doi:10.1002/anie.201814634 · Cited by 402
Mechanistic Studies of the Palladium(II)-Catalyzed Copolymerization of Ethylene with Carbon Monoxide
Rix, F. C., Brookhart, M., & White, P. S. (1996) · Journal of the American Chemical Society · doi:10.1021/ja953276t · Cited by 345
Nickel catalysis for ethylene homo- and co-polymerization
Klabunde, U., & Itten, S. D. (1987) · Journal of Molecular Catalysis · doi:10.1016/0304-5102(87)80023-8 · Cited by 332
Olefins and Vinyl Polar Monomers: Bridging the Gap for Next Generation Materials
Keyes, A., Basbug Alhan, H. E., Ordonez, E., Ha, U., Beezer, D. B., Dau, H., Liu, Y., Tsogtgerel, E., Jones, G. R., & Harth, E. (2019) · Angewandte Chemie International Edition · doi:10.1002/anie.201900650 · Cited by 261
Catalytic Hydroxylation of Polyethylenes
Bunescu, A., Lee, S., Li, Q., & Hartwig, J. F. (2017) · ACS Central Science · doi:10.1021/acscentsci.7b00255 · Cited by 252
Photochemistry of Ketone Polymers. I. Studies of Ethylene-Carbon Monoxide Copolymers
Hartley, G. H., & Guillet, J. E. (1968) · Macromolecules · doi:10.1021/ma60002a012 · Cited by 227
Chen, L., Malollari, K. G., Uliana, A., Sanchez, D., Messersmith, P. B., & Hartwig, J. F. (2021) · Chem · doi:10.1016/j.chempr.2020.11.020 · Cited by 225
Nickel Catalyzed Copolymerization of Ethylene and Alkyl Acrylates
Xin, B. S., Sato, N., Tanna, A., Oishi, Y., Konishi, Y., & Shimizu, F. (2017) · Journal of the American Chemical Society · doi:10.1021/jacs.6b13051 · Cited by 212
Zhang, Y., Mu, H., Pan, L., Wang, X., & Li, Y. (2018) · ACS Catalysis · doi:10.1021/acscatal.8b01088 · Cited by 200
Drent, E., van Dijk, R., van Ginkel, R., van Oort, B., & Pugh, R. I. (2002) · Chemical Communications · doi:10.1039/b111629k · Cited by 192
Zuideveld, M. A., Wehrmann, P., Röhr, C., & Mecking, S. (2004) · Angewandte Chemie International Edition · doi:10.1002/anie.200352062 · Cited by 177
Self-citationJones, D. J., Gibson, V. C., Green, S. M., Maddox, P. J., White, A. J. P., & Williams, D. J. (2005) · Journal of the American Chemical Society · doi:10.1021/ja0518171 · Cited by 169
NMR Spectra of Polymers and Polymer Additives
Brandolini, A. J., & Hills, D. D. (2000) · CRC Press eBooks · doi:10.1201/9781482293425 · Cited by 157
Erhard, G. (2008) · Carl Hanser Verlag GmbH & Co. KG eBooks · doi:10.3139/9783446417502 · Cited by 157
Dos and do nots when assessing the biodegradation of plastics
Zumstein, M. T., Narayan, R., Kohler, H.-P. E., McNeill, K., & Sander, M. (2019) · Environmental Science & Technology · doi:10.1021/acs.est.9b04513 · Cited by 139
Comparative study on biodegradability of polyethylene wax by bacteria and fungi
Kawai, F., Watanabe, M., Shibata, M., Yokoyama, S., Sudate, Y., & Hayashi, S. (2004) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2004.03.015 · Cited by 119
Neutral Nickel(II) Catalysts: From Hyperbranched Oligomers to Nanocrystal-Based Materials
Mecking, S., & Schnitte, M. (2020) · Accounts of Chemical Research · doi:10.1021/acs.accounts.0c00540 · Cited by 119
Self-citationMicrobial Degradation of High-Molecular-Weight Alkanes
Haines, J. R., & Alexander, M. (1974) · Applied Microbiology · doi:10.1128/aem.28.6.1084-1085.1974 · Cited by 113
Photodegradable branched polyethylenes from carbon monoxide copolymerization under benign conditions
Morgen, T. O., Baur, M., Göttker‐Schnetmann, I., & Mecking, S. (2020) · Nature Communications · doi:10.1038/s41467-020-17542-5 · Cited by 101
Self-citationControl of the Molecular Weight of Polyethene in Syntheses with Bis(ylide)nickel Catalysts
Ostoja Starzewski, K. A., & Witte, J. (1987) · Angewandte Chemie International Edition in English · doi:10.1002/anie.198700631 · Cited by 98
Andrady, A. L., Pegram, J. E., & Song, Y. (1993) · Journal of Environmental Polymer Degradation · doi:10.1007/bf01418205 · Cited by 85
Newsham, D. K., Borkar, S., Sen, A., Conner, D. M., & Goodall, B. L. (2007) · Organometallics · doi:10.1021/om700523m · Cited by 85
Uniform shape monodisperse single chain nanocrystals by living aqueous catalytic polymerization
Schnitte, M., Staiger, A., Casper, L. A., et al. (2019) · Nature Communications · doi:10.1038/s41467-019-10692-1 · Cited by 84
Self-citationChen, C., Anselment, T. M. J., Fröhlich, R., et al. (2011) · Organometallics · doi:10.1021/om200628r · Cited by 73
Ligand effects in the non-alternating CO–ethylene copolymerization by palladium(ii) catalysis
Bettucci, L., Bianchini, C., Claver, C., Suarez, E. J. G., Ruiz, A., Meli, A., & Oberhauser, W. (2007) · Dalton Transactions · doi:10.1039/b711280g · Cited by 71
The microstructure and melt properties of CO–ethylene copolymers with remarkably low CO content
Soomro, S. S., Cozzula, D., Leitner, W., Vogt, H., & Müller, T. E. (2014) · Polym. Chem. · doi:10.1039/c3py01637d · Cited by 63
Zhang, Y.-P., Mu, H., Wang, X., Pan, L., & Li, Y. (2019) · ChemCatChem · doi:10.1002/cctc.201900265 · Cited by 58
Kondoh, A., Aoki, T., & Terada, M. (2015) · Chemistry - A European Journal · doi:10.1002/chem.201501377 · Cited by 56
Long-Spaced Polyketones from ADMET Copolymerizations as Ideal Models for Ethylene/CO Copolymers
Ortmann, P., Wimmer, F. P., & Mecking, S. (2015) · ACS Macro Letters · doi:10.1021/acsmacrolett.5b00324 · Cited by 52
Self-citationProtection of Alcohols and Phenols with Dihydropyran and Detetrahydropyranylation by ZrCl4
Rezai, N., Meybodi, F. A., & Salehi, P. (2000) · Synthetic Communications · doi:10.1080/00397910008087225 · Cited by 49
Jeremic, D. (2014) · Ullmann's Encyclopedia of Industrial Chemistry · doi:10.1002/14356007.a21_487.pub3 · Cited by 48
(2007) · doi:10.1007/978-3-540-68411-4 · Cited by 36
Thermodynamic Properties of Ethylene
Sychev, V. V., Selover, T. B., & Azbel, V. D. (1987) · Medical Entomology and Zoology · Cited by 34
Piovano, A., Zarupski, J., & Groppo, E. (2020) · The Journal of Physical Chemistry Letters · doi:10.1021/acs.jpclett.0c01665 · Cited by 26
Morgen, T. O., Krumova, M., Luttikhedde, H. J. G., et al. (2018) · Macromolecules · doi:10.1021/acs.macromol.8b00440 · Cited by 24
Self-citationGöttker‐Schnetmann, I., & Mecking, S. (2020) · Organometallics · doi:10.1021/acs.organomet.0c00500 · Cited by 21
Self-citationBertleff, W., Roeper, M., & Sava, X. (2007) · Ullmann's Encyclopedia of Industrial Chemistry · doi:10.1002/14356007.a05_217.pub2 · Cited by 17
Stafford, C., & Arndtsen, B. A. (2010) · Inorganica Chimica Acta · doi:10.1016/j.ica.2010.12.024 · Cited by 4
Keim, W., Kowaldt, F. H., Goddard, R., & Krueger, C. (1978) · ChemInform · doi:10.1002/chin.197836089 · Cited by 2
Research works printed but not linked: 2
- Press release by Hyosung of May 5 2016: Hyosung introduces the polyketone brand ‘POKETONE™’ to the global market (retrieved June 8 2021 from www.poketone.com).
- C. E. Ash, D. G. Waters, A. A. Smaardijk, Soc. Plast. Eng. 53, 2319 (1995).
Cited by
Recyclable and (Bio)degradable Polyesters in a Circular Plastics Economy
Shi, C., Quinn, E. C., Diment, W. T., & Chen, E. Y.-X. (2024) · Chemical Reviews · doi:10.1021/acs.chemrev.3c00848 · Cited by 402
Mohanty, A. K., Wu, F., Mincheva, R., Hakkarainen, M., Raquez, J.-M., Mielewski, D. F., Narayan, R., Netravali, A. N., & Misra, M. (2022) · Nature Reviews Methods Primers · doi:10.1038/s43586-022-00124-8 · Cited by 355
Recent advances in polymers and polymer composites for food packaging
Zhang, M., Biesold, G. M., Choi, W., Yu, J., Deng, Y., Silvestre, C., & Lin, Z. (2022) · Materials Today · doi:10.1016/j.mattod.2022.01.022 · Cited by 335
Sustainable developments in polyolefin chemistry: Progress, challenges, and outlook
Wang, X.-Y., Gao, Y., & Tang, Y. (2023) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2023.101713 · Cited by 204
Chemically recyclable polyolefin-like multiblock polymers
Zhao, Y., Rettner, E. M., Harry, K. L., Hu, Z., Miscall, J., Rorrer, N. A., & Miyake, G. M. (2023) · Science · doi:10.1126/science.adh3353 · Cited by 205
Metadata
- Authors
- Baur, M., Lin, F., Morgen, T. O., Odenwald, L., & Mecking, S.
- Affiliations
- University of Konstanz (DE)
- Corresponding author
- Mecking, Stefan
- Venue
- Science
- Published
- 2021-10-29
- Volume
- 374
- Issue
- 6567
- Pages
- 604-607
- ISSN
- 0036-8075 (ISSN-L)
- 1095-9203
- OpenAlex
- W3211073624
- Semantic Scholar
- 56143bd9bef2a397e2c0692f3981fe7fe06e9634
- Cited by
- 287
- References
- 46
- Citations by year
- 2026: 60 · 2025: 72 · 2024: 65 · 2023: 40 · 2022: 42 · 2021: 8
- FWCI
- 14.88
- Type
- journal article
- Language
- en
- Open access
- green
- doi.org
- Licence
- cc-by-nc-nd
- Locations
- Science (publishedVersion)
- ChemRxiv (submittedVersion, cc-by-nc-nd)
- PubMed (publishedVersion)
- Figshare (submittedVersion, cc-by-nc-nd)
- KOPS (University of Konstanz) (submittedVersion)
- Funders
- H2020 European Research Council (832480)
- Topics
- Physical Sciences › Chemistry › Organic Chemistry › Organometallic Complex Synthesis and Catalysis
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Physical Sciences › Chemistry › Organic Chemistry › Advanced Polymer Synthesis and Characterization
- Keywords
- polyethylene, high-density polyethylene, tensile properties, injection molding
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-12, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-12 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.