Activity and Stability of Ordered and Disordered Co‐Pt Alloys for Phosphoric Acid Fuel Cells
Open accessThe DOI matches its Crossref record.
Abstract
Co‐Pt alloys were studied in detail by a corrosion test under phosphoric acid fuel cell (PAFC) conditions on the well‐defined crystallographic structures for a typical combination of the alloy catalysts used in PAFCs, examining the long‐life stabilities of the structures and the catalytic activities for electroreduction. The ordered (O) and disordered (D) alloys at the same particle sizes can be obtained by heat‐treating the mother alloy in different temperature sequences. The O‐alloy exhibits a specific activity, an electrocatalytic activity based on the catalyst surface area, 1.35 times higher than the D‐alloy before the corrosion test, but shows less activity (0.73 times) after the corrosion test, due to a higher degradation (47%) in the O‐alloy activity as compared with that of the D‐alloy (1%). It was found that the Co atoms on particle surfaces of both alloys dissolve easily in the acid. This is followed by a second slow dissolution from inside the alloy particles probably due to the protective action by a monolayer thickness of Pt remaining on the alloy surfaces, but the loss of Co in the second stage dissolution for the O‐alloy is higher by several percentage points compared to that of the D‐alloy. It was also found that the Pt content does not change on the catalyst support even after 50 h of corrosion test, but the pure Pt phase is formed in the corrosion product, where the phase for the O‐alloy grows faster than that for the D‐alloy with corrosion time. Based on these results, obtained by chemical, x‐ray diffraction, and transmission electron microscopy with energy dispersive spectroscopy analyses, the corrosion for Pt alloy catalysts is clearly explained, i.e. , after the dissolution of Co atoms in the first surface layer of alloys, both Co and Pt dissolve out simultaneously from small‐size alloy particles and the Pt redeposits on the surfaces of large‐size alloy particles (Ostwald ripening). It is concluded that the D‐alloy is preferable to the O‐alloy from the viewpoint of the stabilities in the structure and the electrocatalytic activity, differing from previous claims.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“Although previous work reported low activities for ordered Pt-alloy catalysts such as Pt-Co catalysts, due to particle sintering during high-temperature annealing, attention has recently been given to the ordered alloy phase of Pt intermetallic compounds in an effort to explore more active carbon-supported Pt-alloy catalysts with superior catalytic performance.264,420”
Citations
Cites
Still being checked.
Cited by
Recent Advances in Electrocatalysts for Oxygen Reduction Reaction
Shao, M., Chang, Q., Dodelet, J.-P., & Chenitz, R. (2016) · Chemical Reviews · doi:10.1021/acs.chemrev.5b00462 · Cited by 3,903
Science and technology roadmap for graphene, related two-dimensional crystals, and hybrid systems
Ferrari, A. C., Bonaccorso, F., Fal'ko, V., Novoselov, K. S., Roche, S., Bøggild, P., Borini, S., Koppens, F. H. L., Palermo, V., Pugno, N., et al. (2015) · Nanoscale · doi:10.1039/c4nr01600a · Cited by 3,027
Wang, D., Xin, H. L., Hovden, R., Wang, H., Yu, Y., Muller, D. A., DiSalvo, F. J., & Abruña, H. D. (2013) · Nature Materials · doi:10.1038/nmat3458 · Cited by 2,082
A review of PEM fuel cell durability: Degradation mechanisms and mitigation strategies
Wu, J., Yuan, X. Z., Martin, J. J., Wang, H., Zhang, J., Shen, J., Wu, S., & Merida, W. (2008) · Journal of Power Sources · doi:10.1016/j.jpowsour.2008.06.006 · Cited by 1,587
Cui, C., Gan, L., Heggen, M., Rudi, S., & Strasser, P. (2013) · Nature Materials · doi:10.1038/nmat3668 · Cited by 1,283
Wang, Y.-J., Zhao, N., Fang, B., Li, H., Bi, X. T., & Wang, H. (2015) · Chemical Reviews · doi:10.1021/cr500519c · Cited by 1,267
Understanding and approaches for the durability issues of Pt-based catalysts for PEM fuel cell
Shao, Y., Yin, G., & Gao, Y. (2007) · Journal of Power Sources · doi:10.1016/j.jpowsour.2007.07.004 · Cited by 1,197
Nanostructured Pt-alloy electrocatalysts for PEM fuel cell oxygen reduction reaction
Bing, Y., Liu, H., Zhang, L., Ghosh, D., & Zhang, J. (2010) · Chemical Society Reviews · doi:10.1039/b912552c · Cited by 1,154
Palladium in fuel cell catalysis
Antolini, E. (2009) · Energy & Environmental Science · doi:10.1039/b820837a · Cited by 1,100
Recent advances in activity and durability enhancement of Pt/C catalytic cathode in PEMFC
Yu, X., & Ye, S. (2007) · Journal of Power Sources · doi:10.1016/j.jpowsour.2007.07.048 · Cited by 1,098
Recent advances in catalysts for direct methanol fuel cells
Zhao, X., Yin, M., Ma, L., Liang, L., Liu, C., Liao, J., Lu, T., & Xing, W. (2011) · Energy & Environmental Science · doi:10.1039/c1ee01307f · Cited by 939
Liquid organic and inorganic chemical hydrides for high-capacity hydrogen storage
Zhu, Q.-L., & Xu, Q. (2015) · Energy & Environmental Science · doi:10.1039/c4ee03690e · Cited by 862
Synthesis and Oxygen Reduction Activity of Shape-Controlled Pt3Ni Nanopolyhedra
Zhang, J., Yang, H., Fang, J., & Zou, S. (2010) · Nano Letters · doi:10.1021/nl903717z · Cited by 788
Nanostructured electrode materials for electrochemical energy storage and conversion
Manthiram, A., Vadivel Murugan, A., Sarkar, A., & Muraliganth, T. (2008) · Energy & Environmental Science · doi:10.1039/b811802g · Cited by 638
Adsorption and Dissociation of O 2 on Pt−Co and Pt−Fe Alloys
Xu, Y., Ruban, A. V., & Mavrikakis, M. (2004) · Journal of the American Chemical Society · doi:10.1021/ja031701+ · Cited by 636
Progress in Solid Oxide Fuel Cells with Nickel-Based Anodes Operating on Methane and Related Fuels
Wang, W., Su, C., Wu, Y., Ran, R., & Shao, Z. (2013) · Chemical Reviews · doi:10.1021/cr300491e · Cited by 510
Furukawa, S., & Komatsu, T. (2017) · ACS Catalysis · doi:10.1021/acscatal.6b02603 · Cited by 509
Antolini, E., Salgado, J. R. C., & Gonzalez, E. R. (2006) · Journal of Power Sources · doi:10.1016/j.jpowsour.2006.03.006 · Cited by 503
Stability of platinum based alloy cathode catalysts in PEM fuel cells
Colón-Mercado, H. R., & Popov, B. N. (2006) · Journal of Power Sources · doi:10.1016/j.jpowsour.2005.05.011 · Cited by 479
A comprehensive review of PBI-based high temperature PEM fuel cells
Araya, S. S., Zhou, F., Liso, V., Sahlin, S. L., Vang, J. R., Thomas, S., Gao, X., Jeppesen, C., & Kær, S. K. (2016) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2016.09.024 · Cited by 463
Bezerra, C. W. B., Zhang, L., Liu, H., Lee, K., Marques, A. L. B., Marques, E. P., Wang, H., & Zhang, J. (2007) · Journal of Power Sources · doi:10.1016/j.jpowsour.2007.08.028 · Cited by 439
Effect of carbon black support corrosion on the durability of Pt/C catalyst
Wang, J., Yin, G., Shao, Y., Zhang, S., Wang, Z., & Gao, Y. (2007) · Journal of Power Sources · doi:10.1016/j.jpowsour.2007.06.084 · Cited by 441
Zatoń, M., Rozière, J., & Jones, D. J. (2017) · Sustainable Energy & Fuels · doi:10.1039/c7se00038c · Cited by 435
Enhancement of the electrocatalytic O2 reduction on Pt–Fe alloys
Toda, T., Igarashi, H., & Watanabe, M. (1999) · Journal of Electroanalytical Chemistry · doi:10.1016/s0022-0728(98)00361-1 · Cited by 429
Self-citationGreen, C. L., & Kucernak, A. (2002) · The Journal of Physical Chemistry B · doi:10.1021/jp0131931 · Cited by 423
The methanol oxidation reaction on platinum alloys with the first row transition metals
Antolini, E., Salgado, J. R. C., & Gonzalez, E. R. (2006) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2005.09.014 · Cited by 415
The recent progress and future of oxygen reduction reaction catalysis: A review
Stacy, J., Regmi, Y. N., Leonard, B., & Fan, M. (2017) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2016.09.135 · Cited by 410
Shape-Control and Electrocatalytic Activity-Enhancement of Pt-Based Bimetallic Nanocrystals
Porter, N. S., Wu, H., Quan, Z., & Fang, J. (2013) · Accounts of Chemical Research · doi:10.1021/ar3002238 · Cited by 393
Xu, D., Liu, Z., Yang, H., Liu, Q., Zhang, J., Fang, J., Zou, S., & Sun, K. (2009) · Angewandte Chemie International Edition · doi:10.1002/anie.200900293 · Cited by 385
Yasuda, K., Taniguchi, A., Akita, T., Ioroi, T., & Siroma, Z. (2006) · Phys. Chem. Chem. Phys. · doi:10.1039/b514342j · Cited by 376
Aricò, A. S., Shukla, A. K., Kim, H., Park, S., Min, M., & Antonucci, V. (2001) · Applied Surface Science · doi:10.1016/s0169-4332(00)00831-x · Cited by 375
An Efficient CoAuPd/C Catalyst for Hydrogen Generation from Formic Acid at Room Temperature
Wang, Z., Yan, J., Ping, Y., Wang, H., Zheng, W., & Jiang, Q. (2013) · Angewandte Chemie International Edition · doi:10.1002/anie.201301009 · Cited by 368
Chen, S., Gasteiger, H. A., Hayakawa, K., Tada, T., & Shao-Horn, Y. (2010) · Journal of The Electrochemical Society · doi:10.1149/1.3258275 · Cited by 360
A review of polymer electrolyte membrane fuel cell durability test protocols
Yuan, X.-Z., Li, H., Zhang, S., Martin, J., & Wang, H. (2011) · Journal of Power Sources · doi:10.1016/j.jpowsour.2011.07.082 · Cited by 354
PtCo/C cathode catalyst for improved durability in PEMFCs
Yu, P., Pemberton, M., & Plasse, P. (2005) · Journal of Power Sources · doi:10.1016/j.jpowsour.2004.11.067 · Cited by 350
Electrochemical Energy Conversion on Intermetallic Compounds: A Review
Rößner, L., & Armbrüster, M. (2019) · ACS Catalysis · doi:10.1021/acscatal.8b04566 · Cited by 342
A General Strategy for Preparation of Pt 3d-Transition Metal (Co, Fe, Ni) Nanocubes
Zhang, J., & Fang, J. (2009) · Journal of the American Chemical Society · doi:10.1021/ja908245r · Cited by 341
Nano-stuctured Pt–Fe/C as cathode catalyst in direct methanol fuel cell
Li, W., Zhou, W., Li, H., Zhou, Z., Zhou, B., Sun, G., & Xin, Q. (2004) · Electrochimica Acta · doi:10.1016/j.electacta.2003.10.015 · Cited by 308
Atomic Arrangement Engineering of Metallic Nanocrystals for Energy-Conversion Electrocatalysis
Liang, J., Ma, F., Hwang, S., Wang, X., Sokolowski, J., Li, Q., Wu, G., & Su, D. (2019) · Joule · doi:10.1016/j.joule.2019.03.014 · Cited by 305
Khan, K., Tareen, A. K., Aslam, M., Zhang, Y., Wang, R., Ouyang, Z., Gou, Z., & Zhang, H. (2019) · Nanoscale · doi:10.1039/c9nr05919a · Cited by 302
Chen, S., Ferreira, P. J., Sheng, W., Yabuuchi, N., Allard, L. F., & Shao-Horn, Y. (2008) · Journal of the American Chemical Society · doi:10.1021/ja802513y · Cited by 277
Chen, S., Sheng, W., Yabuuchi, N., Ferreira, P. J., Allard, L. F., & Shao-Horn, Y. (2009) · The Journal of Physical Chemistry C · doi:10.1021/jp807143e · Cited by 273
Shukla, A. K., Neergat, M., Bera, P., Jayaram, V, & Hegde, M. S. (2001) · Journal of Electroanalytical Chemistry · doi:10.1016/s0022-0728(01)00421-1 · Cited by 258
Oezaslan, M., & Strasser, P. (2011) · Journal of Power Sources · doi:10.1016/j.jpowsour.2010.11.016 · Cited by 241
Xiong, L., & Manthiram, A. (2005) · Journal of The Electrochemical Society · doi:10.1149/1.1862256 · Cited by 238
Structure and Activity of Carbon-Supported Pt−Co Electrocatalysts for Oxygen Reduction
Salgado, J. R. C., Antolini, E., & Gonzalez, E. R. (2004) · The Journal of Physical Chemistry B · doi:10.1021/jp0486649 · Cited by 215
Antolini, E. (2017) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2017.05.081 · Cited by 210
Platinum-based ternary catalysts for low temperature fuel cells
Antolini, E. (2007) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2007.03.001 · Cited by 197
Koh, S., Toney, M. F., & Strasser, P. (2007) · Electrochimica Acta · doi:10.1016/j.electacta.2006.08.039 · Cited by 181
Oezaslan, M., Hasché, F., & Strasser, P. (2012) · Journal of The Electrochemical Society · doi:10.1149/2.075204jes · Cited by 175
Zhang, K., Yue, Q., Chen, G., Zhai, Y., Wang, L., Wang, H., Zhao, J., Liu, J., Jia, J., & Li, H. (2011) · The Journal of Physical Chemistry C · doi:10.1021/jp108305v · Cited by 147
Malacrida, P., Escudero-Escribano, M., Verdaguer-Casadevall, A., Stephens, I. E. L., & Chorkendorff, I. (2014) · Journal of Materials Chemistry A · doi:10.1039/c3ta14574c · Cited by 138
Xiong, L., & Manthiram, A. (2004) · J. Mater. Chem. · doi:10.1039/b400968c · Cited by 115
Venkateswara Rao, C., & Viswanathan, B. (2009) · The Journal of Physical Chemistry C · doi:10.1021/jp9041606 · Cited by 96
Koh, S., Yu, C., Mani, P., Srivastava, R., & Strasser, P. (2007) · Journal of Power Sources · doi:10.1016/j.jpowsour.2007.01.002 · Cited by 94
First principles computational study on the electrochemical stability of Pt–Co nanocatalysts
Noh, S. H., Seo, M. H., Seo, J. K., Fischer, P., & Han, B. (2013) · Nanoscale · doi:10.1039/c3nr02611f · Cited by 78
Salvatore Aricò, A., Stassi, A., Gatto, I., Monforte, G., Passalacqua, E., & Antonucci, V. (2010) · The Journal of Physical Chemistry C · doi:10.1021/jp104528q · Cited by 59
Selvaganesh, S. V., Sridhar, P., Pitchumani, S., & Shukla, A. K. (2013) · Journal of The Electrochemical Society · doi:10.1149/2.051301jes · Cited by 28
Sarkar, A., Kerr, J. B., & Cairns, E. J. (2013) · ChemPhysChem · doi:10.1002/cphc.201200917 · Cited by 12
Metadata
- Authors
- Watanabe, M., Tsurumi, K., Mizukami, T., Nakamura, T., & Stonehart, P.
- Affiliations
- University of Yamanashi (JP)
- TANAKA PRECIOUS METAL TECHNOLOGIES Co., Ltd. (Japan) (JP)
- Stonehart Associates, Incorporated, 17 Cottage Road, P.O. Box 1220, Madison, Connecticut 06443
- ORCID
- Watanabe, Masahiro
- Venue
- Journal of The Electrochemical Society
- Publisher
- The Electrochemical Society
- Published
- 1994-10-01
- Volume
- 141
- Issue
- 10
- Pages
- 2659-2668
- ISSN
- 0013-4651 (ISSN-L)
- 1945-7111
- OpenAlex
- W2025120588
- Cited by
- 412
- References
- 0
- Citations by year
- 2026: 4 · 2025: 10 · 2024: 7 · 2023: 9 · 2022: 13 · 2021: 9 · 2020: 11 · 2019: 8 · 2018: 13 · 2017: 18 · 2016: 18 · 2015: 21 · 2014: 24 · 2013: 31 · 2012: 29
- FWCI
- 3.92
- Type
- journal article
- Language
- en
- Open access
- bronze
- doi.org
- Licence
- iopscience.iop.org/page/copyright (vor, 9198 d)
- iopscience.iop.org/info/page/text-and-data-mining (tdm, 9198 d)
- Locations
- Journal of The Electrochemical Society (publishedVersion)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Fuel Cells and Related Materials
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Electrocatalysts for Energy Conversion
- Physical Sciences › Materials Science › Materials Chemistry › Catalytic Processes in Materials Science
- Keywords
- CoPt alloys, phosphoric acid fuel cells, electrocatalytic activity, catalyst stability, ordered alloys, disordered alloys, corrosion, cobalt dissolution, platinum redeposition, Ostwald ripening, heat treatment, catalyst deactivation
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.