Strain Derivatives for Practical Charge Rate Characterization of Lithium Ion Electrodes
Open accessThe DOI matches its Crossref record; 22 of the 23 references it cites were found in a registry or an index, and 1 are not checked yet.
Abstract
During battery use, electrode materials are known to expand and contract in repeatable patterns, and this strain has been previously correlated with battery properties such as state of charge and state of health. In this study, we show that the second derivative of strain, d 2 ɛ/dQ 2 , is mathematically proportional to dV/dQ within an electrode stage. We also experimentally quantify peaks in the strain curves for electrode stage transitions at practical charge rates of up to C/2 and confirm that transitions are visible in the practical scenario of discharging at the higher rate of 1C. Moreover, the location of the transition measured by d 2 ɛ/dQ 2 changes by less than 10% from 0.05 C to 0.5 C, but the transition measured with dV/dQ decreases by more than 15% from 0.05 C to 0.3 C, demonstrating the reliability of strain to measure electrode transitions at moderate charge rates. We also note that d 2 ɛ/dQ 2 exhibits similar peak shifts as those expected in dV/dQ as the cell ages. Our derivations for the model system of graphite and lithium cobalt oxide can be generalized to other battery systems and used to characterize materials at practical charge rates impossible with only voltage.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Figures










Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“In general, differential curves are very sensitive to the sampling level, cell performance change and measurement noise.Therefore, smoothing is the first and most important step for SOH analysis, achieved by various filtering techniques, such as moving average [49], Gaussian filter [53] and Savitzky-Golay filter [55,56].”
From Data-driven health estimation and lifetime prediction of lithium-ion batteries: A review (2019) · cites this paper as [56]
Experimental — accuracy not yet measuredThe source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“The second derivative of the strain with respect to capacity (dε 2 /dQ 2 ) was shown to exhibit similar shifts in peaks as those expected in the DV curves during the cell degradation process but in a more consistent and reliable manner.”
From Data-driven health estimation and lifetime prediction of lithium-ion batteries: A review (2019) · cites this paper as [56]
Experimental — accuracy not yet measuredThe cited source says what the claim attributes to it.
In the citing paper
“Despite these disadvantages, the strain derivative analysis remains a practical tool when cells are cycled under higher current rates, which is the main hurdle for IC/DV analysis [56].”
From Data-driven health estimation and lifetime prediction of lithium-ion batteries: A review (2019) · cites this paper as [56]
The cited source says what the claim attributes to it.
In the citing paper
“The dε 2 /dQ 2 curves were applied for identifying phase transitions in electrode materials at higher current rates than the DV analysis, making the method more time efficient.”
From Data-driven health estimation and lifetime prediction of lithium-ion batteries: A review (2019) · cites this paper as [56]
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Electrochemical and In Situ X‐Ray Diffraction Studies of Lithium Intercalation in Li x CoO2
Reimers, J. N., & Dahn, J. R. (1992) · Journal of The Electrochemical Society · doi:10.1149/1.2221184 · Cited by 1,723
Ohzuku, T., Iwakoshi, Y., & Sawai, K. (1993) · Journal of The Electrochemical Society · doi:10.1149/1.2220849 · Cited by 1,089
Dahn, J. R. (1991) · Physical Review B · doi:10.1103/physrevb.44.9170 · Cited by 991
Modeling and Simulation of Lithium-Ion Batteries from a Systems Engineering Perspective
Northrop, P. W. C., De, S., Braatz, R. D., Ramadesigan, V., Northrop, P. W. C., Santhanagopalan, S., & Subramaniana, V. R. (2011) · DSpace@MIT (Massachusetts Institute of Technology) · Cited by 753
Differential voltage analyses of high-power, lithium-ion cells
Bloom, I., Jansen, A. N., Abraham, D. P., Knuth, J., Jones, S. A., Battaglia, V. S., & Henriksen, G. L. (2005) · Journal of Power Sources · doi:10.1016/j.jpowsour.2004.07.021 · Cited by 585
Takami, N., Satoh, A., Hara, M., & Ohsaki, T. (1995) · Journal of The Electrochemical Society · doi:10.1149/1.2044017 · Cited by 436
Battery cycle life prediction with coupled chemical degradation and fatigue mechanics
Deshpande, R., Verbrugge, M., Cheng, Y.-T., Wang, J., & Liu, P. (2012) · Journal of The Electrochemical Society · doi:10.1149/2.049210jes · Cited by 389
Understanding Solid Electrolyte Interface Film Formation on Graphite Electrodes
Zhang, S., Ding, M. S., Xu, K., Allen, J., & Jow, T. R. (2001) · Electrochemical and Solid-State Letters · doi:10.1149/1.1414946 · Cited by 373
A Guide to Li-Ion Coin-Cell Electrode Making for Academic Researchers
Marks, T., Trussler, S., Smith, A. J., Xiong, D., & Dahn, J. R. (2011) · Journal of The Electrochemical Society · doi:10.1149/1.3515072 · Cited by 290
State of health and charge measurements in lithium-ion batteries using mechanical stress
Cannarella, J., & Arnold, C. B. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.07.003 · Cited by 278
Self-citationA new method for detecting lithium plating by measuring the cell thickness
Bitzer, B., & Gruhle, A. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.03.142 · Cited by 260
Dahn, H. M., Smith, A. J., Burns, J. C., Stevens, D. A., & Dahn, J. R. (2012) · Journal of The Electrochemical Society · doi:10.1149/2.013209jes · Cited by 246
Rate dependence of swelling in lithium-ion cells
Oh, K.-Y., Siegel, J. B., Secondo, L., Kim, S. U., Samad, N. A., Qin, J., Anderson, D., Garikipati, K., Knobloch, A., Epureanu, B. I., et al. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.05.039 · Cited by 219
Real-time stress measurements in lithium-ion battery negative-electrodes
Sethuraman, V. A., Van Winkle, N., Abraham, D. P., Bower, A. F., & Guduru, P. R. (2012) · Journal of Power Sources · doi:10.1016/j.jpowsour.2012.01.036 · Cited by 219
Fu, R., Xiao, M., & Choe, S.-Y. (2012) · Journal of Power Sources · doi:10.1016/j.jpowsour.2012.09.096 · Cited by 163
A Dilatometric Study of Lithium Intercalation into Powder-Type Graphite Electrodes
Hahn, M., Buqa, H., Ruch, P. W., Goers, D., Spahr, M. E., Ufheil, J., Novák, P., & Kötz, R. (2008) · Electrochemical and Solid-State Letters · doi:10.1149/1.2940573 · Cited by 129
Long-Term Low-Rate Cycling of LiCoO2/Graphite Li-Ion Cells at 55°C
Smith, A. J., Dahn, H. M., Burns, J. C., & Dahn, J. R. (2012) · Journal of The Electrochemical Society · doi:10.1149/2.056206jes · Cited by 115
Mohan, S. N., Kim, Y., Siegel, J. B., Samad, N. A., & Stefanopoulou, A. G. (2014) · Journal of The Electrochemical Society · doi:10.1149/2.0841414jes · Cited by 114
Sommer, L. W., Raghavan, A., Kiesel, P., Saha, B., Schwartz, J., Lochbaum, A., Ganguli, A., Bae, C.-J., & Alamgir, M. (2015) · Journal of The Electrochemical Society · doi:10.1149/2.0361514jes · Cited by 79
Vetter, K. J. (1963) · Journal of The Electrochemical Society · doi:10.1149/1.2425837 · Cited by 68
Barker, J. (1999) · Electrochimica Acta · doi:10.1016/s0013-4686(99)00207-8 · Cited by 39
On the coupling between stress and voltage in lithium-ion pouch cells
Cannarella, J., Leng, C. Z., & Arnold, C. B. (2014) · Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE · doi:10.1117/12.2055152 · Cited by 39
Self-citationModeling and Simulation of Lithium-Ion Batteries from Systems Engineering Perspective
Ramadesigan, V., Northrop, P. W. C., De, S., Santhanagopalan, S., Braatz, R. D., & Subramanian, V. R. (2010) · ECS Meeting Abstracts · doi:10.1149/2.018203jes · Cited by 12
Cited by
Data-driven health estimation and lifetime prediction of lithium-ion batteries: A review
Li, Y., Liu, K., Foley, A. M., Zülke, A., Berecibar, M., Nanini-Maury, E., Van Mierlo, J., & Hoster, H. E. (2019) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2019.109254 · Cited by 1,193
“A few studies have investigated the first and second derivative of strain with respect to charge (dε/dQ and dε2/dQ2) [56,73] and strain differential to voltage (dε/dV) [72].”
BackgroundMethodInfluentialWang, Z., Feng, G., Zhen, D., Gu, F., & Ball, A. (2021) · Energy Reports · doi:10.1016/j.egyr.2021.08.113 · Cited by 441
Review on state-of-health of lithium-ion batteries: Characterizations, estimations and applications
Yang, S., Zhang, C., Jiang, J., Zhang, W., Zhang, L., & Wang, Y. (2021) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2021.128015 · Cited by 435
Multi-scale investigation of thickness changes in a commercial pouch type lithium-ion battery
Rieger, B., Schlueter, S., Erhard, S. V., Schmalz, J., Reinhart, G., & Jossen, A. (2016) · Journal of Energy Storage · doi:10.1016/j.est.2016.01.006 · Cited by 210
Understanding Full-Cell Evolution and Non-chemical Electrode Crosstalk of Li-Ion Batteries
Knehr, K. W., Hodson, T., Bommier, C., Davies, G., Kim, A., & Steingart, D. A. (2018) · Joule · doi:10.1016/j.joule.2018.03.016 · Cited by 127
Metadata
- Authors
- Schiffer, Z. J., Cannarella, J., & Arnold, C. B.
- Affiliations
- Princeton University (US)
- DuPont (United States) (US)
- Venue
- Journal of The Electrochemical Society
- Publisher
- The Electrochemical Society
- Published
- 2015-12-16
- Volume
- 163
- Issue
- 3
- Pages
- A427-A433
- ISSN
- 0013-4651 (ISSN-L)
- 1945-7111
- OpenAlex
- W2562129302
- Semantic Scholar
- 43911639a95e7583335d627eed5e72201ec60bfc
- Cited by
- 59
- References
- 22
- Citations by year
- 2026: 4 · 2025: 6 · 2024: 6 · 2023: 6 · 2022: 4 · 2021: 9 · 2020: 6 · 2019: 4 · 2018: 3 · 2017: 4 · 2016: 7
- FWCI
- 4.81
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- cc-by
- Locations
- Journal of The Electrochemical Society (publishedVersion, cc-by)
- Topics
- Physical Sciences › Engineering › Automotive Engineering › Battery Modeling and Management
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Battery Materials
- Physical Sciences › Materials Science › Metals and Alloys › Extraction and Separation Processes
- Keywords
- lithium-ion batteries, strain derivatives, charging rate, graphite, LiCoO2, battery state of health, battery degradation
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.