Optimization Analysis of Vibration Reduction for Large‐Span Steel Pedestrian Bridges Based on Tuned Mass Damper Inerter System
Open accessThe DOI matches its Crossref record; 19 of the 19 references it cites were found in a registry or an index; 2 of the 10 sources its claims cite were checked for support.
Abstract
Aiming at the problem of the narrow damping frequency band of traditional single‐tuned mass damper (STMD), this paper proposes multiple‐tuned mass dampers (MTMDs) and six different configurations of tuned mass damper inerter systems (TMDI‐Ⅰ–TMDI‐VI) for vibration suppression optimization. A long‐span steel truss footbridge was selected as the research object, a vibration simulation model of a single‐degree‐of‐freedom pedestrian bridge‐damping system was established by Matlab Simulink, and the vibration damping effects of STMD, MTMD, and six TMDI damping systems under human‐induced excitation were compared and analyzed. The results indicate that the damping effect of MTMD is better than that of STMD when the self‐oscillating frequency of the footbridge is deviated, and its robustness is further improved with the increase in the number of MTMD subunits n. The damping effect of the six TMDI damping systems varies greatly, among which TMDI-III has the best damping effect and robustness, when |λ| = 5%, the damping rate α of the TMDI‐III damping system is still able to increase by 8.3% compared with that of STMD. The research results can provide theoretical support for the vibration reduction control of large‐span steel truss footbridge.
Overview
CoChat Summary
TL;DR
This paper compares single-tuned mass damper (STMD), multiple-tuned mass dampers (MTMDs), and six tuned mass damper inerter (TMDI) configurations for vibration control of a 123 m steel truss pedestrian bridge under pedestrian-induced excitation. It finds MTMD is more robust than STMD when the bridge frequency deviates, and TMDI-III gives the best damping and robustness among the six TMDI configurations.
Key findings
- Under the same mass ratio, n-MTMD is not superior to STMD when the main structure’s natural frequency does not deviate, but MTMD performs better than STMD when the frequency deviates; robustness improves as the number of MTMD subunits n increases. Specifically, 3-MTMD is better than STMD when |λ| ≥ 2%, 5-MTMD is better regardless of λ, and 7-MTMD and 3-MTMD are better than STMD when |λ| ≥ 2%.
- The six TMDI configurations differ greatly. TMDI-III has the best damping effect and robustness; at |λ| = 5%, its damping rate α is still 8.3% higher than STMD. TMDI-I also remains better than STMD at |λ| = 5%, with α 1.7% higher.
- TMDI-II and TMDI-V are weaker than STMD at larger deviations: at |λ| = 5%, TMDI-II has α = 60.4%, a decrease of 7.5% compared with STMD, and TMDI-V has α = 55.0%, a decrease of 12.9%. TMDI-IV and TMDI-VI are stable for |λ| ≤ 2% (α decreases of only 0.8% and 2.1% versus central frequency), but at |λ| = 5% their peak acceleration exceeds STMD, with α decreases of 0.5% and 1.7%.
- Model validation against Midas Civil gave STMD damping rates α of 85.85% for Matlab Simulink and 81.79% for Midas Civil, a difference of 4.72%.
Methods
- The case study is the XuanYue Bridge, a large-span simply supported steel truss pedestrian bridge with a 123 m span, 9 m cantilevers on each side, total length 155 m, deck width from 8.0 m at the abutment to 10.1 m at midspan, depth 1.5 m, and Q355D steel. A Midas Civil finite element model used beam elements for truss members, plate elements for deck panels, and Lanczos modal eigenvalue calculation; in situ dynamic tests showed a maximum deviation rate between measured and calculated natural frequencies of less than 6.2%.
- The bridge-damping system was simplified to a single-degree-of-freedom model in Matlab Simulink. Human-induced excitation followed EN03 (2007): Fv(t) = P × cos(2π f_s t) × n0 φ, with P = 280 N, crowd density n = 1.5 people/m², f_s = 1.47 Hz, and φ = 0.55.
- STMD, MTMD (n = 3, 5, 7; η = 0.15), and six TMDI configurations were compared under mass ratio μ = 0.01. The analysis compared peak acceleration and damping rate α under deviations λ of the main structure resonance frequency to assess damping effectiveness and robustness.
Limitations
- The paper states that the Matlab Simulink model simplifies the controlled main structure to a single-degree-of-freedom system, while real pedestrian bridge vibration under human-induced excitation is produced by coupling of multiple modalities; the simulation neglects higher natural modes.
- The paper states that for TMDI configurations IV, V, and VI, the added spring element k_t1 leads to higher-order equations beyond the fourth order, making analytical optimal tuning expressions difficult; numerical solutions were used instead.
- Evident from the text: the study is based on one bridge case and simulation results; the proposed MTMD and TMDI systems are not field-validated, and the model validation is shown only for the STMD case against Midas Civil.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
2 Valid · 0 Not valid · 9 Not checked · 44 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“This device, utilizing the strong mass amplification effect of the inerter, can replace part of the TMD mass to achieve lightweight vibration control.”
§ Optimization Analysis of Vibration Reduction for Large-Span Steel Pedestrian Bridges Based on Tuned Mass Damper Inerter System > 1. Introduction
What the sources say
- Supportedcites [16] matched to “Optimal design of a novel tuned mass-damper–inerter (TMDI) passive vibration control configuration for stochastically support-excited structural systems” (2014) source
The Abstract (p. 3) states that the TMDI uses the inerter’s mass amplification effect and can replace part of the TMD vibrating mass to achieve lightweight passive vibration control. The concluding remarks (p. 29) likewise describe a significantly lighter solution through TMD mass replacement. (LLM, conf=0.94)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“when jλj: ¼ 5%, the damping rate α of the TMDI-III damping system is still able to increase by 8.3% compared with that of STMD.”
§ Optimization Analysis of Vibration Reduction for Large-Span Steel Pedestrian Bridges Based on Tuned Mass Damper Inerter System > Abstract
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Modal identification of the pedestrian bridge reveals a first vertical bending mode frequency of 1.47 Hz”
§ Optimization Analysis of Vibration Reduction for Large-Span Steel Pedestrian Bridges Based on Tuned Mass Damper Inerter System > 2.1. Vibration Dynamics Model of Vibration Damping System.
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“and its robustness is further improved with the increase in the number of MTMD subunits n.”
§ Optimization Analysis of Vibration Reduction for Large-Span Steel Pedestrian Bridges Based on Tuned Mass Damper Inerter System > Abstract
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The results indicate that the damping effect of MTMD is better than that of STMD when the selfoscillating frequency of the footbridge is deviated”
§ Optimization Analysis of Vibration Reduction for Large-Span Steel Pedestrian Bridges Based on Tuned Mass Damper Inerter System > Abstract
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
32 more claims
Create a free account to see all 55 claims and every source verdict.
- Probably not a substantial claim. 7
- It may state two separate claims as one. 14
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ Optimization Analysis of Vibration Reduction for Large-Span Steel Pedestrian Bridges Based on Tuned Mass Damper Inerter System > 4. Conclusion
“when the natural frequency of the main structure does not deviate, the damping control effect of n-MTMD is not superior to STMD.”
§ Optimization Analysis of Vibration Reduction for Large-Span Steel Pedestrian Bridges Based on Tuned Mass Damper Inerter System > 3.3. MTMDs Vibration Damping Performance Analysis.
“For 5-MTMD, regardless of the value of the deviation degree λ of the main structure resonance frequency, its damping effect is better than STMD;”
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ Optimization Analysis of Vibration Reduction for Large-Span Steel Pedestrian Bridges Based on Tuned Mass Damper Inerter System > 2.1. Vibration Dynamics Model of Vibration Damping System.
“Modal identification of the pedestrian bridge reveals a first vertical bending mode frequency of 1.47 Hz”
§ Optimization Analysis of Vibration Reduction for Large-Span Steel Pedestrian Bridges Based on Tuned Mass Damper Inerter System > 4. Conclusion
“| 1 | 0.98 | 0.95 | 2.9 | 1.69 | 1st vertical bending | | 2 | 1.47 | 1.40 | 5.7 | 1.39 | 1st lateral bending |”
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
“C ¼ 2M × ð2πf d Þ: × ξ ¼ 2 × 350:4 × 10 3 × ð2π × 1:40Þ: × 1:39% ¼ 4:28 × 10 4 N × s=m:”
§ Optimization Analysis of Vibration Reduction for Large-Span Steel Pedestrian Bridges Based on Tuned Mass Damper Inerter System > 2.2. Mechanical Model of STMD Damping System.
Reported 42800 · recomputed 85687.366883
Citations
Cites
Synthesis of mechanical networks: the inerter
Smith, M. C. (2002) · IEEE Transactions on Automatic Control · doi:10.1109/tac.2002.803532 · Cited by 1,828
BISHOP, R. E. D. (1957) · Nature · doi:10.1038/179504a0 · Cited by 1,636 · cited 1×
“…kg, and the spring stiffness k p is determined according to structural dynamics equations: The parameters m t , k t , and ξ t in the STMD are selected based on the optimal frequency ratio and optimal damping ratio calculation formulas derived from the fi xed point theory proposed by Den Hartog [22].”
Marian, L., & Giaralis, A. (2014) · Probabilistic Engineering Mechanics · doi:10.1016/j.probengmech.2014.03.007 · Cited by 828 · cited 1×
“By integrating the inerter with the STMD system, structural vibration reduction performance can be enhanced without increasing the TMD ’ s physical mass. Marian et al. [16] combined the traditional TMD with an inerter to develop a vibration reduction system called tuned mass damper inerter (TMDI).”
Seismic control of single‐degree‐of‐freedom structure using tuned viscous mass damper
Ikago, K., Saito, K., & Inoue, N. (2012) · Earthquake Engineering & Structural Dynamics · doi:10.1002/eqe.1138 · Cited by 782 · cited 1×
“Among these, the ball-screw inerter, investigated by Ikago et al. [14], is widely adopted due to its practical feasibility.”
Dynamic characteristics of multiple substructures with closely spaced frequencies
Xu, K., & Igusa, T. (1992) · Earthquake Engineering & Structural Dynamics · doi:10.1002/eqe.4290211203 · Cited by 326 · cited 1×
“Xu and Igusa [7] studied an MTMD vibration reduction system with subunits having the same spring stiffness and linearly distributed natural frequencies, providing expressions for the optimal damping ratio and frequency ratio of the MTMD system.”
Performance evaluation for inerter-based dynamic vibration absorbers
Hu, Y., & Chen, M. Z. Q. (2015) · International Journal of Mechanical Sciences · doi:10.1016/j.ijmecsci.2015.06.003 · Cited by 325 · cited 2×
“However, Hu [24] and others still provided numerical solutions obtained through Matlab calculations.”
Nagarajaiah, S. (2009) · Structural Control and Health Monitoring · doi:10.1002/stc.349 · Cited by 256
Crowd-induced random vibration of footbridge and vibration control using multiple tuned mass dampers
Li, Q., Fan, J., Nie, J., Li, Q., & Chen, Y. (2010) · Journal of Sound and Vibration · doi:10.1016/j.jsv.2010.04.013 · Cited by 169 · cited 1×
“…TMD controlling vertical displacement and TMD controlling torsional displacement can maximize the vibration reduction effect of TMD. Li et al. [9] proposed an optimization design method for MTMD systems based on minimizing the root mean square value of maximum acceleration on pedestrian…”
Dai, J., Xu, Z.-D., & Gai, P.-P. (2019) · Engineering Structures · doi:10.1016/j.engstruct.2019.109585 · Cited by 163 · cited 5×
“To ensure the accuracy of the computational model, our research team conducted in situ dynamic characteristic tests on the bridge [18], and comparative results between numerical predictions and fi eld measurements are presented in Table 2.”
InfluentialWang, L., Nagarajaiah, S., Shi, W., & Zhou, Y. M. (2021) · Engineering Structures · doi:10.1016/j.engstruct.2021.112743 · Cited by 143 · cited 1×
“…degradation during service, errors in fi nite element model calculations, and human – structure interaction (HSI) [4] can all lead to deviations in the fundamental frequency of the structure, causing detuning effects [5] in STMD and signi fi cantly reducing its vibration reduction effectiveness.”
Research works printed but not linked: 6
- Van Nimmen K., 2014, Footbridge, 170
- Miguel L. F. F., 2023, Robust Optimum Design of MTMD for Control of Footbridges Subjected to Human-Induced Vibrations via the CIOA, Structural Engineering and Mechanics, 86, 647
- Zhang R. F., 2019, Inerter System and Its State-of-the-Art, Engineerig Mechanics, 36, 8
- GiaralisA.andTaflanidisA. Robust Reliability-Based Design of Seismically Excited Tuned Mass-Damper-Inerter (TMDI) Equipped MDOF Structures With Uncertain Properties 6th European Conference on Structural Control Paper No. 150 2016 City University London.
- Jiao J. F., 2023, Reserch on Pedestrian-Induced Vibration Test and Damping Control of Long-Span Simple-Supported Steel Truss Girder Pedestrian Bridge, Chinese, Journal of Taiyuan University of Technology, 54, 1083
- Li C. X., 2003, Comparative Study on Performance of Acceleration-Response-Control-Based MTMD for Structures Under Various Excitations, Chinese, Journal of Vibration and Shock, 22, 91
Cited by
Masnata, C., Basili, M., & Pirrotta, A. (2026) · Structures · doi:10.1016/j.istruc.2026.112917
Metadata
- Authors
- Song, R.-F., Wang, J.-L., Yang, Z.-S., & Ma, S.-J.
- Affiliations
- Zhengzhou University of Technology (CN)
- Corresponding author
- Ma, Shi-Ju
- ORCID
- Ma, Shi-Ju
- Venue
- Advances in Civil Engineering
- Publisher
- Wiley
- Published
- 2025-01
- Volume
- 2025
- Issue
- 1
- ISSN
- 1687-8086 (ISSN-L)
- 1687-8094
- OpenAlex
- W4409864355
- Cited by
- 2
- References
- 18
- Citations by year
- 2026: 1 · 2025: 1
- FWCI
- 0.64
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- cc-by
- creativecommons.org/licenses/by/4.0/ (vor, 116 d)
- doi.wiley.com/10.1002/tdm_license_1.1 (tdm)
- Locations
- Advances in Civil Engineering (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- Zhengzhou University (24GC02)
- Topics
- Physical Sciences › Engineering › Civil and Structural Engineering › Structural Engineering and Vibration Analysis
- Physical Sciences › Engineering › Civil and Structural Engineering › Vibration Control and Rheological Fluids
- Physical Sciences › Engineering › Mechanical Engineering › Vibration and Dynamic Analysis
- Keywords
- tuned mass damper inerter, multiple tuned mass dampers, pedestrian-induced vibration, vibration suppression, damping rate
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-12, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-12 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.