CoChat

A review of the oxidation behaviour of structural alloys in steam

Wright, I G, Dooley, R B · 2010 · International Materials Reviews
Cited by 361

The DOI matches its Crossref record; 50 of the 50 references it cites were found in a registry or an index.

Abstract

The focus of this review is the state of knowledge of the oxidation behaviour in steam of alloys with potential for use as pressure parts in steam boilers. The rate of oxide growth on steam-touched surfaces and the characteristics of that oxide are of increasing interest as the quest for improvements in cycle efficiency leads to progressively higher operating temperatures and pressures. The consequences of increased rate of growth of these oxides are of concern because of implications for tube overheating and oxide exfoliation. Mitigation of such problems requires a mechanistic understanding of the influences of alloy composition and microstructure, and especially of the evolution with time of specific scale structures. Similarly, the relative effects of factors such as time, temperature and operating parameters must be understood. The oxidation behaviour of the class of ferritic steels that forms the bulk of the heat transfer surface in steam boilers is of particular importance since alloys in the range 9-12%Cr (% in alloy compositions signifies weight percentage, unless indicated otherwise) are close to a transition from oxidation behaviour based on relatively thick Fe-based scales to the formation of much thinner, Cr-rich oxides. For austenitic steels protective behaviour in steam depends critically on the rapid development of a continuous Cr-rich oxide layer, otherwise oxide growth rates similar to the ferritic steels may result. Understanding the interplay among compositional and microstructural requirements for strengthening and oxidation resistance, and their influence on the rate and mode of scale evolution is key to the most effective application of these alloys. The oxidation behaviour of high-temperature Ni-based alloys in steam has received relatively little attention, but the broad range of alloying additions considered, compared to austenitic steels, has the potential to contribute in different ways to the scale morphologies and oxidation behaviour. Underlying these interests is the apparently significant contribution to oxide growth in steam from inward transport of oxidant species that likely involve hydrogen. The particular species involved and their roles in the oxidation process are expected to exert a large influence on the oxide morphologies developed, while the fate of any hydrogen released in the alloy is a further topic of particular interest.

Overview

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1179/095066010x12646898728165

Cites

50 of 50 references verified0 citation errors · 0 not checkable

Statistics

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 50 references

Cited by

See all 361

Metadata

Authors
Wright, I. G., & Dooley, R. B.
Venue
International Materials Reviews
Published
2010-05
Volume
55
Issue
3
Pages
129-167
ISSN
  • 0950-6608 (ISSN-L)
  • 1743-2804
OpenAlex
W2085035634
Cited by
361
References
50
FWCI
28.80
Type
journal article
Language
en
Open access
closed

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: A review of the oxidation behaviour of structural alloys in steam. https://app.cochat.ai/papers/10.1179/095066010x12646898728165
The paper
Wright, I. G., & Dooley, R. B. (2010). A review of the oxidation behaviour of structural alloys in steam. International Materials Reviews. https://doi.org/10.1179/095066010x12646898728165

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.