The DOI matches its Crossref record; 8 of the 8 references it cites were found in a registry or an index.
Laser-induced damage on single-crystal metal surfaces
Abstract
Laser-induced damage morphologies and the accumulation dependence of damage on single-crystal metal surfaces have been observed under Q-switched 1064-nm Nd:YAG laser irradiation at 10-nsec pulses. Several different damage morphologies were observed: slip-line formation, ripple patterns, flat melting, and boiling. Damage probability versus fluence curves and accumulation curves are plotted to investigate damage behavior as it correlates with morphology. Flat-melting damage was observed near the 50% damage fluence on chemically polished copper surfaces, and slip lines were found near the 50% damage fluence on electropolished aluminum surfaces. Surface defects produced during sample preparation greatly influenced the damage threshold of copper because of its high melting threshold. Accumulation curves showed different damage behavior for crystals of different orientation. Accumulation was the largest on (111) Cu and Al surfaces, and the single-shot damage threshold of these surfaces was less than the other crystal orientations for both Cu and Al. The threshold reduction in accumulation follows the equation FN = F1NS−1, where FN is the N-pulse damage threshold, N is the pulse number, and S is the slope of the accumulation curve. Accumulation appears to be the result of the storage cycle of thermal stress–strain energy induced by a laser pulse. The total strain energy induced by N laser pulses is proportional to N1/3 for the measured values of S, which is 0.92.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Fatigue: A complex subject—Some simple approximations
Manson, S. S. (1965) · Experimental Mechanics · doi:10.1007/bf02321056 · Cited by 1,372
Effects of High-Power Laser Radiation
(1971) · Elsevier eBooks · doi:10.1016/b978-0-12-583950-1.x5001-6 · Cited by 1,356
Laser-induced periodic surface structure. II. Experiments on Ge, Si, Al, and brass
Young, J. F., Preston, J. S., van Driel, H. M., & Sipe, J. E. (1983) · Physical Review B · doi:10.1103/physrevb.27.1155 · Cited by 663
Growth of spontaneous periodic surface structures on solids during laser illumination
Guosheng, Z., Fauchet, P. M., & Siegman, A. E. (1982) · Physical Review B · doi:10.1103/physrevb.26.5366 · Cited by 471
Bloembergen, N. (1973) · Applied Optics · doi:10.1364/ao.12.000661 · Cited by 448
Stimulated Wood's anomalies on laser-illuminated surfaces
Siegman, A., & Fauchet, P. (1986) · IEEE Journal of Quantum Electronics · doi:10.1109/jqe.1986.1073133 · Cited by 230
Temperature dependence of absorptance in laser damage of metallic mirrors: I Melting
Sparks, M., & Loh, E. (1979) · Journal of the Optical Society of America · doi:10.1364/josa.69.000847 · Cited by 117
Damage thresholds at metal surfaces for short pulse IR lasers
Figueira, J. F., & Thomas, S. J. (1982) · IEEE Journal of Quantum Electronics · doi:10.1109/jqe.1982.1071704 · Cited by 41
Cited by
Borowiec, A., & Haugen, H. K. (2003) · Applied Physics Letters · doi:10.1063/1.1586457 · Cited by 645
Mannion, P. T., Magee, J., Coyne, E., O’Connor, G. M., & Glynn, T. J. (2004) · Applied Surface Science · doi:10.1016/j.apsusc.2004.03.229 · Cited by 629
Femtosecond-laser ablation dynamics of dielectrics: basics and applications for thin films
Balling, P., & Schou, J. (2013) · Reports on Progress in Physics · doi:10.1088/0034-4885/76/3/036502 · Cited by 475
Fabrication of Micro/Nano Structures on Metals by Femtosecond Laser Micromachining
Ahmmed, K., Grambow, C., & Kietzig, A.-M. (2014) · Micromachines · doi:10.3390/mi5041219 · Cited by 466
A review of ultrafast laser materials micromachining
Cheng, J., Liu, C.-S., Shang, S., Liu, D., Perrie, W., Dearden, G., & Watkins, K. (2013) · Optics & Laser Technology · doi:10.1016/j.optlastec.2012.06.037 · Cited by 416
Metadata
- Authors
- Jee, Y., Becker, M. F., & Walser, R. M.
- Venue
- Journal of the Optical Society of America B
- Publisher
- Optica Publishing Group
- Published
- 1988-03-01
- Volume
- 5
- Issue
- 3
- Pages
- 648
- ISSN
- 0740-3224 (ISSN-L)
- 1520-8540
- OpenAlex
- W2120600654
- Cited by
- 537
- References
- 8
- FWCI
- 4.57
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.