Student or educator? Sign up with your school email and get 6 months of Pro free.
CoChat

The DOI matches its Crossref record; 41 of the 41 references it cites were found in a registry or an index; 1 of the 3 sources its claims cite were checked for support.

Enhancing metasurface fabricability through minimum feature size enforcement

Open access

Abstract

The metasurfaces have shown great potential for miniaturizing conventional optics while offering extended flexibility. Recently, there has been considerable interest in using algorithms to generate meta-atom shapes for these metasurfaces, as they offer vast design freedom and not biased by the human intuition. However, these complex designs significantly increase the difficulty of fabrication. To address this, we introduce a design process that rigorously enforces the fabricability of both the material-filled (fill) and empty (void) regions in a metasurface design. This process takes into account specific constraints regarding the minimum feature size for each region. Additionally, it corrects any violations of these constraints across the entire device, ensuring only minimal impact on performance. Our method provides a practical way to create metasurface designs that are easy to fabricate, even with complex shapes, hence improving the overall production yield of these advanced meta-optical components.

Overview

CoChat Summary

## TL;DR

The paper presents a device-level algorithm that enforces minimum feature size on both fill and void regions in metasurface layouts, aiming to make complex free-form designs fabrication-friendly. In a 40 μm-diameter silicon metalens example designed for 1064 nm, MFS correction improved fabrication quality and experimental performance relative to the non-corrected layout.

## Key findings

  • The algorithm checks and corrects metasurface layouts at the entire device level using a “rolling circle” method, separately enforcing MFSf for fill regions and MFSv for void regions.
  • In the demonstrated metalens, the layout had a 40 μm diameter, a 600 nm lattice constant, and an MFS requirement of 100 nm for both fills and voids.
  • SEM images showed that the non-fabricable regions stuck together when fabricated without correction, while with MFS correction the meta-atoms were successfully resolved and fabrication quality “increased dramatically.”
  • The corrected metalens had only slight performance decrease in numerical simulations, whereas the uncorrected fabricated metalens showed a significantly shifted focal distance and a broadened focal spot and depth of focus.

## Methods

  • The paper proposes a four-step algorithm: it checks fill polygons, checks void polygons, checks distances between fill polygons, and checks distances between void polygons and their enclosing fill boundaries.
  • The method uses a rolling circle of radius equal to the relevant MFS; fabricability is inferred from the number of circle–polygon intersections.
  • Demonstrations include a silicon-on-glass metalens and another fabricated metasurface with free-form shapes including high-aspect-ratio features up to 26:1; fabrication was evaluated with SEM imaging and optical characterization.

## Limitations

  • The paper states that the algorithm is an additional design-step and is meant to work before proximity effect correction (PEC); it does not claim PEC alone can solve non-fabricability.
  • Evident from the text: the paper demonstrates the approach on specific metalens examples, so broader performance across other metasurface types or fabrication platforms is not directly shown.
  • Evident from the text: the correction aims for minimal impact on performance, but the paper still notes a slight decrease in numerical performance after correction.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.1515/nanoph-2024-0150

Cites

41 of 41 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Figures

Figure 1: An artistic depiction illustrating various cases of MFS violations. Regions where the ‘fill’ requirements are not met are highlighted in red and labeled as ① and ②, while regions indicating ‘void’ requirement violations are marked in orange and labeled as ③ and ④. The regions that have been corrected in the design are distinctly marked in cyan for easy identification.
Figure 1: An artistic depiction illustrating various cases of MFS violations. Regions where the ‘fill’ requirements are not met are highlighted in red and labeled as ① and ②, while regions indicating ‘void’ requirement violations are marked in orange and labeled as ③ and ④. The regions that have been corrected in the design are distinctly marked in cyan for easy identification.CC BY · PubMed Central
Figure 2: An illustration of the four steps in the ‘rolling circle’ method for assessing the fabricability of metasurface designs. (a) Step 1: A rolling circle with a radius R = MFSf evaluates the fabricability of a single fill region. (b) Step 2: A rolling circle with a radius R = MFSv evaluates the fabricability of a single void. (c) Step 3: A rolling circle with a radius R = MFSv checks the distance between two fill regions. (d) Step 4: A rolling circle with a radius R = MFSf checks the distance between two voids.
Figure 2: An illustration of the four steps in the ‘rolling circle’ method for assessing the fabricability of metasurface designs. (a) Step 1: A rolling circle with a radius R = MFSf evaluates the fabricability of a single fill region. (b) Step 2: A rolling circle with a radius R = MFSv evaluates the fabricability of a single void. (c) Step 3: A rolling circle with a radius R = MFSv checks the distance between two fill regions. (d) Step 4: A rolling circle with a radius R = MFSf checks the distance between two voids.CC BY · PubMed Central
Figure 3: A detailed flowchart illustrates the workflow of the algorithm.
Figure 3: A detailed flowchart illustrates the workflow of the algorithm.CC BY · PubMed Central
Figure 4: The process of checking layout fabricability. The check begins from the bottom left corner and proceeds along the x-axis; after completing a row, the algorithm moves to the leftmost atom in the row above. (a) A single meta-atom is checked for fabricability. (b–e) Four different scenarios for different meta-atom positions in the layout. (f) The final metasurface layout, where all meta-atoms are fixed. In (a–e), the meta-atoms under assessment are marked in red, fixed meta-atoms in green, and those yet to be checked in grey.
Figure 4: The process of checking layout fabricability. The check begins from the bottom left corner and proceeds along the x-axis; after completing a row, the algorithm moves to the leftmost atom in the row above. (a) A single meta-atom is checked for fabricability. (b–e) Four different scenarios for different meta-atom positions in the layout. (f) The final metasurface layout, where all meta-atoms are fixed. In (a–e), the meta-atoms under assessment are marked in red, fixed meta-atoms in green, and those yet to be checked in grey.CC BY · PubMed Central
Figure 5: The layouts, fabricated metalenses, and performance evaluation before and after correction. (a, b) The layouts of the metalenses before and after correction. (c, d) SEM images of fabricated metalenses before and after correction. The insets in (c) and (d) showcase the same areas as the insets in panels (a) and (b). (e) Comparison of the focusing performance of the ‘ideal’ metalenses before and after correction numerically calculated using beam propagation method. The metalenses show similar performance with ‘after correction’ metalens being just slightly worse. (f) Comparison of experimentally measured performance of the fabricated metalenses before and after correction. The ‘before correction’ metalens shows the degraded performance.
Figure 5: The layouts, fabricated metalenses, and performance evaluation before and after correction. (a, b) The layouts of the metalenses before and after correction. (c, d) SEM images of fabricated metalenses before and after correction. The insets in (c) and (d) showcase the same areas as the insets in panels (a) and (b). (e) Comparison of the focusing performance of the ‘ideal’ metalenses before and after correction numerically calculated using beam propagation method. The metalenses show similar performance with ‘after correction’ metalens being just slightly worse. (f) Comparison of experimentally measured performance of the fabricated metalenses before and after correction. The ‘before correction’ metalens shows the degraded performance.CC BY · PubMed Central
Figure 6: SEM images of an MFS-corrected metalens consisting of freeform meta-atoms. The minimum feature size requirements are strictly met, enabling maximal use of geometrical degrees of freedom. (a) Top view. (b) Tilted view.
Figure 6: SEM images of an MFS-corrected metalens consisting of freeform meta-atoms. The minimum feature size requirements are strictly met, enabling maximal use of geometrical degrees of freedom. (a) Top view. (b) Tilted view.CC BY · PubMed Central

Verification

Claims the paper makes

1 Valid · 0 Not valid · 1 Not checked · 20 Own results and interpretations

7 more claims

Create a free account to see all 22 claims and every source verdict.

See all claims — free account
  • Probably not a substantial claim. 5
  • It may state two separate claims as one. 9

Create a free account to see these claims.

Citations

Cites

Show all 40 references

Research works printed but not linked: 8

  1. 10.1021/ACS.NANOLETT.2C03561/SUPPL_FILE/NL2C03561_SI_002.PDF · doi:10.1021/acs.nanolett.2c03561/suppl_file/nl2c03561_si_002.pdf
  2. 10.1021/ACSNANO.3C09462/ASSET/IMAGES/LARGE/NN3C09462_0005.JPEG · doi:10.1021/acsnano.3c09462/asset/images/large/nn3c09462_0005.jpeg
  3. 10.1515/NANOPH‐2020‐0063/ASSET/GRAPHIC/J_NANOPH‐2020‐0063_FIG_007.JPG · doi:10.1515/nanoph-2020-0063/asset/graphic/j_nanoph-2020-0063_fig_007.jpg
  4. 10.1021/ACS.CHEMREV.2C00012/ASSET/IMAGES/LARGE/CR2C00012_0035.JPEG · doi:10.1021/acs.chemrev.2c00012/asset/images/large/cr2c00012_0035.jpeg
  5. 10.1515/NANOPH‐2022‐0152/ASSET/GRAPHIC/J_NANOPH‐2022‐0152_FIG_005.JPG · doi:10.1515/nanoph-2022-0152/asset/graphic/j_nanoph-2022-0152_fig_005.jpg
  6. 10.1515/NANOPH‐2019‐0117/DOWNLOADASSET/SUPPL/NANOPH‐2019‐0117_SUPPL.ZIP · doi:10.1515/nanoph-2019-0117/downloadasset/suppl/nanoph-2019-0117_suppl.zip
  7. 10.1021/ACSPHOTONICS.2C01166/SUPPL_FILE/PH2C01166_SI_002.PDF · doi:10.1021/acsphotonics.2c01166/suppl_file/ph2c01166_si_002.pdf
  8. 10.1021/ACSPHOTONICS.3C00113/ASSET/IMAGES/LARGE/PH3C00113_0006.JPEG · doi:10.1021/acsphotonics.3c00113/asset/images/large/ph3c00113_0006.jpeg

Cited by

See all 7

Metadata

Authors
Terekhov, P., Chang, S., Rahman, M. T., Shafi, S., Ahn, H., Zhao, L., & Ni, X.
Affiliations
Pennsylvania State University (US)
Corresponding author
Ni, Xingjie
Venue
Nanophotonics
Publisher
Wiley
Published
2024-05-21
Volume
13
Issue
17
Pages
3147-3154
ISSN
  • 2192-8606 (ISSN-L)
  • 2192-8614
OpenAlex
W4398140114
Cited by
7
References
40
Citations by year
2026: 5 · 2025: 2
FWCI
0.55
Type
journal article
Language
en
Open access
Locations
  • Nanophotonics (publishedVersion, cc-by)
  • PubMed Central (publishedVersion, cc-by)
  • PubMed (publishedVersion)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
Funders
  • Division of Chemistry (CHE‐2305139)
  • Division of Electrical, Communications and Cyber Systems (ECCS‐1609693, ECCS‐2047446)
  • National Eye Institute (1R21EY031853‐01)
Topics
  • Physical Sciences › Materials Science › Electronic, Optical and Magnetic Materials › Metamaterials and Metasurfaces Applications
  • Physical Sciences › Engineering › Electrical and Electronic Engineering › Advanced Antenna and Metasurface Technologies
  • Physical Sciences › Materials Science › Surfaces, Coatings and Films › Optical Coatings and Gratings
Keywords
metasurfaces, metasurface fabrication, void regions, meta-optics, fabrication yield

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).

A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Enhancing metasurface fabricability through minimum feature size enforcement. https://app.cochat.ai/papers/10.1515/nanoph-2024-0150
The paper
Terekhov, P., Chang, S., Rahman, M. T., Shafi, S., Ahn, H., Zhao, L., & Ni, X. (2024). Enhancing metasurface fabricability through minimum feature size enforcement. Nanophotonics. https://doi.org/10.1515/nanoph-2024-0150

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.