The Influence of the Design Features of the Submersible Pump Rotor on the Vibration Reliability
Open accessAbstract
Pumping equipment consumes about 20 % of the electrical energy produced by humankind. A significant, even drastic, reduction in the weight and size indicators of pumping equipment leads to a decrease in the cost price and, therefore, competitiveness of such products in the market. Simultaneously, it makes it possible to use more valuable and high-quality construction materials and technologies that improve the reliability of equipment and its energy efficiency, which in turn is a clear step in solving many UN Sustainable Development Goals (SDGs). According to the research results, it was proved that by increasing the frequency of the drive, it is possible to reduce the mass and size indicators of the submersible pump for the needs of the critical infrastructure sector by reducing the number of stages. Mainly, the amplitudes of oscillations near the rotation frequency are 12–22 % and do not exceed 35 % of the gaps in the seals, as required by the available international standards to ensure the guaranteed vibration reliability of the pump. Overall, using a bearingless support design will significantly increase the reliability of the developed pump.
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
Additive manufacturing has opened a new window of application in hydraulic machinery, creating more valuable components and materials with reliable performance, addressing many of the Sustainable Development Goals (SDGs).
“Additive manufacturing (AM) has opened a new window of application in hydraulic machinery, creating more valuable components and materials with reliable performance, addressing many of the Sustainable Development Goals (SDGs) [57].”
From Towards Sustainability in Hydraulic Machinery Manufacturing by 3D Printing (2024) · cites this paper as [57]
The Introduction (page unavailable) links pump development to several SDGs, and the Literature Review (page unavailable) says high-speed pump designs create opportunities to use higher-quality materials and technologies. Neither passage attributes those opportunities to additive manufacturing; the paper instead discusses faster drives, fewer pump stages, and design changes. The claim’s central assertion about AM is therefore unsupported. (LLM, conf=0.86)
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Cites
No references could be resolved yet.
Research works printed but not linked: 23
- Kotenko, A., Herman, V., Kotenko, A. (2014). Rationalization of Ukrainian industrial enterprises in a context of using torque flow pumps on the basis of valuation of the life cycle of pumping equipment. Nauka i Studia, Vol. 16 (126), pp. 83-91. Available online: http://essuir.sumdu.edu.ua/bitstream/123456789/38769/3/kotenko_poland1.PDF
- Ramez, A., Al-Hakimi, W., Perozo, N., Jaeger, P. (2023). Real-time liquid rate and water cut prediction from the electrical submersible pump sensors data using machine-learning algorithms. ACS Omega, Vol. 8(14), pp. 12671-12692. https://doi.org/10.1021/acsomega.2c07609 · DOI
- Aydin, H., Merey, S. (2021). Design of Electrical Submersible Pump system in geothermal wells: A case study from West Anatolia, Turkey. Energy, Vol. 230, 120891. https://doi.org/10.1016/j.energy.2021.120891 · DOI
- Antonenko, S., Sapozhnikov, S., Kondus, V., Chernobrova, A., Mandryka, A. (2021). Creation a universal technique of predicting performance curves for small-sized centrifugal stages of well oil pump units. Journal of Physics: Conference Series, Vol. 1741, 012011. https://doi.org/10.1088/1742-6596/1741/1/012011 · DOI
- Kumar, J., Gopi, S., Amirthagadeswaran, K. (2023). Redesigning and numerical simulation of gating system to reduce cold shut defect in submersible pump part castings. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, Vol. 237 (3), pp. 971-981. https://doi.org/10.1177/09544089221142185 · DOI
- Shuiguang, T., Hang, Z., Huiqin, L., Yue, Y., Jinfu, L., Feiyun, C. (2020). Multi-objective optimization of multistage centrifugal pump based on surrogate model. Fluids, Vol. 142, 011101. https://doi.org/10.1115/1.4043775 · DOI
- Monte Verde, W., Kindermann, E., Biazussi, J.L., Estevam, V., Foresti, B.P., Bannwart, A.C. (2023). Experimental investigation of the effects of fluid viscosity on electrical submersible pumps performance. SPE Production and Operations, Vol. 38(1), pp. 1- 19. https://doi.org/10.2118/210603-PA · DOI
- Gulyi, A., Kobyzska, A. (2014). Existing perspectives of rotodynamic pumps rotation speed increase. Applied Mechanics and Materials, Vol. 630, pp. 91-98. https://doi.org/10.4028/www.scientific.net/AMM.630.91 · DOI
- Yong, H., Ling, B., Danyang, D., Weidong, S., Ling Z. (2023). Effects of tip clearance on energy performance of three-stage electrical submersible pump. Geoenergy Science and Engineering, Vol. 226, 211696. https://doi.org/10.1016/j.geoen.2023.211696 · DOI
- Han, C., Liu, J., Yang, Y., Chen, X. (2023). Influence of blade exit angle on the performance and internal flow pattern of a high- speed electric submersible pump. Water, Vol. 15, 2774. https://doi.org/10.3390/w15152774 · DOI
- Bhattacharjee, P., Hussain, S.A.I., Dey, V. (2023). Failure mode and effects analysis for submersible pump component using proportionate risk assessment model: A case study in the power plant of Agartala. International Journal of System Assurance Engineering and Management, Vol. 14, pp. 1778-1798 https://doi.org/10.1007/s13198-023-01981-6 · DOI
- Yong, H., Ling, B., Danyang, D., Weidong, S., Ling Z. (2023). Effects of tip clearance on energy performance of three-stage electrical submersible pump. Geoenergy Science and Engineering, Vol. 26, 211696. https://doi.org/10.1016/j.geoen.2023.211696 · DOI
- Sun, Z., Wang, L., Ge, H., Yuan, H., Tang, F. (2023). Experiment on pressure pulsation in impeller of large submersible tubular pump. Transactions of the Chinese Society for Agricultural Machinery, Vol. 54(4), pp. 155-160. https://doi.org/10.6041/j.issn.1000-1298.2023.04.014 · DOI
- Firatoglu, Z.A., Alihanoglu, M.N. (2022). Investigation of the effect of the stages number, the impeller outlet width, and the impeller outlet angle on the performance of an industrial electric submersible pump. Journal of Fluids Engineering, Vol. 144, 081203. https://doi.org/10.1115/1.4053652 · DOI
- Horovy, S.O. (1995). Development and Research of Designs of "Shaftless" Centrifugal Pumps. Ph.D. Thesis. Sumy State University, Ukraine.
- Kondus, V., Pavlenko, I., Kulikov, O., Liaposhchenko, O. (2023) Development of a high-rotational submersible pump for water supply. Water, Vol. 15(20), 3609. https://doi.org/10.3390/w15203609 · DOI
- Gulyi, O.M., Zubakhin, A.N (2010). Improvement of centrifugal pump designs based on the use of damping effects of slot-sealed flow parts. Ukrainian Scientific and Technical Journal: Industrial Hydraulics and Pneumatics, Vol 1(27), pp 65-67.
- Martsynkovskyi, V., Pozovnyi, O. (2017). Influence of multi-slot seals on rotor dynamics. Journal of Engineering Sciences, Vol. 4(1), pp. C7-C12. https://doi.org/10.21272/jes.2017.4(1).c2 · DOI
- Zubakhin, A.M. (2011). Use of Hydrodynamic Effects in Slotted Seals to Increase Technical Level of Centrifugal Pumps. Ph.D. Thesis. Sumy State University, Ukraine.
- Monkova, K., Monka, P.P., Hric, S., Kozak, D., Katinič, M., Pavlenko, I., Liaposchenko, O. (2020). Condition monitoring of Kaplan turbine bearings using vibro-diagnostics. International Journal of Mechanical Engineering and Robotics Research, Vol. 9(8), pp. 1182-1188. https://doi.org/10.18178/ijmerr.9.8.1182-1188 · DOI
- Pavlenko, I., Ciszak, O., Kondus, V., Ratushnyi, O., Ivchenko, O., Kolisnichenko, E., Kulikov, O., Ivanov, V. (2023). An increase in the energy efficiency of a new design of pumps for nuclear power plants. Energies, Vol. 16(6), 2929. https://doi.org/10.3390/en16062929 · DOI
- Tenali, N., Kadivendi, S. (2014). Rotor dynamic analysis of steam turbine rotor using ANSYS. International Journal of Mechanical Engineering and Robotics Research, Vol. 3(1), pp. 338-349. https://doi.org/10.18178/ijmerr · DOI
- Lingom, P.M., Song-Manguelle, J., Betoka-Onyama, S.P., Nyobe-Yome, J.M., Doumbia, M.L. (2023). A power quality assessment of electric submersible pumps fed by variable frequency drives under normal and failure modes. Energies, Vol. 16(13), 5121. https://doi.org/10.3390/en16135121 · DOI
Cited by
Sorted by citations
Towards Sustainability in Hydraulic Machinery Manufacturing by 3D Printing
Remache, A., Pérez-Sánchez, M., Hidalgo, V. H., Ramos, H. M., & Sánchez-Romero, F.-J. (2024) · Processes · doi:10.3390/pr12122664 · Cited by 9 · see citing works
- Authors
- Makivskyi, O., Kondus, V., Piteľ, J., Sotnyk, M., Andrusiak, V., Polkovnychenko, V., & Musthai, M.
- Affiliations
- Sumy State University (UA)
- Sumy State University, Sumy, Ukraine
- Technical University of Košice (SK)
- ORCID
- Venue
- Journal of Engineering Sciences
- Publisher
- Sumy State University
- Published
- 2024
- Volume
- 11
- Issue
- 1
- Pages
- D1-D9
- ISSN
- 2312-2498 (ISSN-L)
- 2414-9381
- OpenAlex
- W4391660507
- Cited by
- 6
- References
- 0
- Citations by year
- 2025: 3 · 2024: 3
- FWCI
- 0.89
- Type
- journal article
- Language
- en
- Open access
- diamond
- doi.org
- Licence
- cc-by-nc
- Locations
- Journal of Engineering Sciences (publishedVersion, cc-by-nc)
- Electronic Sumy State University Institutional Repository (Sumy State University) (submittedVersion, cc-by-nc)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- National Research Foundation of Ukraine
- Topics
- Physical Sciences › Engineering › Mechanics of Materials › Cavitation Phenomena in Pumps
- Physical Sciences › Engineering › Mechanical Engineering › Mechanical Engineering Research and Applications
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electric Motor Design and Analysis
- Keywords
- submersible pumps, vibration reliability, excitation frequency, seal clearance
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
