Student or educator? Sign up with your school email and get 6 months of Pro free.
CoChat
Cited by 232

The DOI matches its Crossref record.

Instrumented Indentation Testing

· 2000 · Mechanical Testing and Evaluation

Abstract

INSTRUMENTED INDENTATION TESTING (IIT), also known as depth-sensing indentation, continuous-recording indentation, ultra-low-load indentation, and nanoindentation, is a relatively new form of mechanical testing that significantly expands on the capabilities of traditional hardness testing. Developed largely over the past two decades, IIT employs high-resolution instrumentation to continuously control and monitor the loads and displacements of an indenter as it is driven into and withdrawn from a material (Ref 1–13). Depending on the details of the specific testing system, loads as small as 1 nN can be applied, and displacements of 0.1 nm (1 A) can be measured. Mechanical properties are derived from the indentation load-displacement data obtained in simple tests. The advantages of IIT are numerous, as indentation load-displacement data contain a wealth of information, and techniques have been developed for characterizing a variety of mechanical properties. The technique most frequently employed measures the hardness, but it also gives the elastic modulus (Young’s modulus) from the same data (Ref 8, 11). Although not as well-developed, methods have also been devised for evaluating the yield stress and strain-hardening characteristic of metals (Ref 14–16); parameters characteristic of damping and internal friction in polymers, such as the storage and loss modulus (Ref 17, 18); and the activation energy and stress exponent for creep (Ref 19–25). IIT has even been used to estimate the fracture toughness of brittle materials using optical measurement of the lengths of cracks that have formed at the corners of hardness impressions made with special sharp indenters (Ref 13, 26, 27). In fact, almost any material property that can be measured in a uniaxial tension or compression test can conceivably be measured, or at least estimated, using IIT. An equally important advantage of IIT results because load-displacement data can be used to determine mechanical properties without having to image the hardness impressions. This facilitates property measurement at very small scales. Mechanical properties are routinely measured from submicron indentations, and with careful technique, properties have even been determined from indentations only a few nanometers deep. Because of this, IIT has become a primary tool for examining thin films, coatings, and materials with surfaces modified by techniques such as ion implantation and laser heat treatment. Many IIT testing systems are equipped with automated specimen manipulation stages. In these systems, the spatial distribution of the near-surface mechanical properties can be mapped on a point-to-point basis along the surface in a fully automated way. Lateral spatial resolutions of about a micron have been achieved. An example of small indentations located at specific points in an electronic microcircuit is shown in Fig. 1. The purpose of this article is to provide a practical reference guide for instrumented indentation testing. Emphasis is placed on the better-developed measurement techniques and the procedures and calibrations required to obtain accurate and meaningful measurements.

Overview

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.31399/asm.hb.v08.a0003273

Cites

Statistics

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cited by

Metadata

Venue
Mechanical Testing and Evaluation
Published
2000
Pages
232-243
OpenAlex
W2549567744
Cited by
232
References
0
FWCI
11.12
Type
book chapter
Language
en
Open access
closed

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.