The DOI matches its Crossref record; 33 of the 33 references it cites were found in a registry or an index; 1 of the 37 sources its claims cite were checked for support.
An Integrated Thermal-Electrical Model for Simulations of Battery Behavior in CubeSats
Open accessAbstract
This work presents an integrated thermal-electrical simulation model capable of estimating the temperature and energy conditions of the battery along the orbit and attitude.
Overview
CoChat Summary
TL;DR
This paper presents an integrated thermal-electrical simulation model for CubeSats that couples orbit, attitude, irradiance, thermal, electrical, battery, and heater-control models to estimate battery temperature and energy conditions along an orbit. Simulations for a 1U CubeSat illustrate trade-offs between battery heating and state of charge under fixed and variant temperature setpoints.
Key findings
- The integrated model can simulate battery and PV thermal/electrical behavior at each time instant in a given orbit and attitude, including mutual effects and user-defined heater control.
- In the no-heater case, the battery reached 265 K in eclipse regions despite the CubeSat attaining highest energy levels; with fixed setpoints T_set = 273, 278, and 283 K, the heater was on during eclipse for 520, 916, and 1305 s, respectively.
- Variant setpoints by energy level (T_set = [273, 278, 281, 283, 288] K) let SoC recover faster and remain higher during orbit; the heater was on for 307 s during eclipse, the lowest among simulated scenarios.
- Without eclipse energy-saving mode, SoC variations were greater, tending to decrease battery useful life, and the CubeSat did not return to energy level L = 5. MPPT perturb-and-observe was also illustrated, including using surplus power for the heater.
Methods
- The model uses seven nodes (six PV panels and one battery) with circular orbit, attitude, irradiance, lumped-parameter thermal energy balance, direct-energy-transfer electrical power system, solar-panel diode model, and battery RC model; equations solved with Newton-Raphson, timestep 1 s over 12 orbits.
- Case study: 1U FloripaSat-I, near-circular Sun-synchronous orbit at 620 km, inclination simplified to 90°, passive magnetic attitude with 2 rotations/orbit about ERF [1,0,0] and 10 rotations/orbit about ORF [0,0,1]; initial SoC 50%; heater R_H = 10 Ω; energy modes L with P_L from 0.25 to 2.75 W.
- Simulations compared no heater control, fixed T_set = 273/278/283 K, variant setpoints, no eclipse energy-saving mode, and MPPT.
Limitations
- The paper states heat transfer among main parts is simplified using thermal resistance; the model can support more nodes but conduction/radiation remain simplified, a trade-off for computational cost and preliminary design. Future work suggests a more accurate thermal model of solar panels, e.g., finite volumes.
- Model assumptions stated in the paper include circular orbit without perturbations, constant material properties, PV does not generate heat, infinite thermal resistance among solar panels, gray surfaces, perfect vacuum, and constant solar irradiance of 1360 W/m² despite real variations being within model uncertainties.
- Evident from the text: the case-study altitude is stated as 620 km in Section 4 but as 650 km in the Conclusions, an inconsistency in the reported setup.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures





















Verification
Claims the paper makes
0 Valid · 1 Not valid · 24 Not checked · 39 Own results and interpretations
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The heater was kept on for 307 s during the variant case's eclipse, the lowest value among all the simulated scenarios.”
§ An Integrated Thermal-Electrical Model for Simulations of Battery Behavior in CubeSats > 4.1.2. Variant Setpoints
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Maintaining a higher temperature outside the eclipse keeps the battery at a lower voltage and state levels as a negative point.”
§ An Integrated Thermal-Electrical Model for Simulations of Battery Behavior in CubeSats > 4.1. Simulation Results
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The most intensive use of the heater in the defined setpoints occurs in the eclipse regions.”
§ An Integrated Thermal-Electrical Model for Simulations of Battery Behavior in CubeSats > 4.1. Simulation Results
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“the higher expenditure during the eclipse state does not allow the CubeSat to return to the energy level L = 5.”
§ An Integrated Thermal-Electrical Model for Simulations of Battery Behavior in CubeSats > 4.1.3. No Energy-Saving Mode in an Eclipse
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“while trying to follow the maximum power, the system balances between the heater and the execution of tasks.”
§ An Integrated Thermal-Electrical Model for Simulations of Battery Behavior in CubeSats > 4.1.4. MPPT
plainstates a possible cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
21 more claims
Create a free account to see all 64 claims and to verify the 3 references still open.
- Probably not a substantial claim. 18
- It may state two separate claims as one. 22
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ An Integrated Thermal-Electrical Model for Simulations of Battery Behavior in CubeSats > 4. Results
“In this paper, the case study is based on the CubeSat 1U FloripaSat-I, whose orbit is nearly-circular and Sun-synchronous, and has an altitude of 620 km [36].”
§ An Integrated Thermal-Electrical Model for Simulations of Battery Behavior in CubeSats > 5. Conclusions
“To illustrate the proposed model, a simulation scenario was generated for a 1U CubeSat in an orbit at 650 km with altitude and dynamics typical of CubeSats with passive attitude control.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ An Integrated Thermal-Electrical Model for Simulations of Battery Behavior in CubeSats > 2.5. Heater Analysis
“From Equation (39) it can be concluded that the cyclical ratio necessary to maintain a certain desired battery temperature is a ratio between its heat exchange and the maximum power input given by the heater.”
§ An Integrated Thermal-Electrical Model for Simulations of Battery Behavior in CubeSats > 2.5. Heater Analysis
“P H (t) = (V B (t)D(t)) 2 R H , (34”
Citations
Cites
Methods for state-of-charge determination and their applications
Piller, S., Perrin, M., & Jossen, A. (2001) · Journal of Power Sources · doi:10.1016/s0378-7753(01)00560-2 · Cited by 1,162 · cited 1×
“Battery The battery model used in this paper assumes that the voltage of the battery is considered equal to the battery’s electromotive force EMF, which is firmly related to SoC in series for an internal resistance RBS and several resistor-capacitor blocks [7,34,35].”
MethodPredictive & Adaptive MPPT Perturb and Observe Method
Femia, N., Granozio, D., Petrone, G., Spagnuolo, G., & Vitelli, M. (2007) · IEEE Transactions on Aerospace and Electronic Systems · doi:10.1109/taes.2007.4383584 · Cited by 406
Spacecraft Thermal Control Handbook, Volume I: Fundamental Technologies
Gilmore, D. (2002) · doi:10.2514/4.989117 · Cited by 352
Performance of solar cells using thermoelectric module in hot sites
Benghanem, M., Al-Mashraqi, A. A., & Daffallah, K. O. (2016) · Renewable Energy · doi:10.1016/j.renene.2015.12.011 · Cited by 139 · cited 1×
“The work of [15] measured a coefficient of loss of around 0.”
BackgroundThermal design and analysis of a nanosatellite in low earth orbit
Corpino, S., Caldera, M., Nichele, F., Masoero, M. C., & Viola, N. (2015) · Acta Astronautica · doi:10.1016/j.actaastro.2015.05.012 · Cited by 127
Energy Storage Technologies for Small Satellite Applications
Chin, K. B., Brandon, E. J., Bugga, R. V., Smart, M. C., Jones, S. C., Krause, F. C., West, W. C., & Bolotin, G. G. (2018) · Proceedings of the IEEE · doi:10.1109/jproc.2018.2793158 · Cited by 87 · cited 3×
“However, as experimentally demonstrated in [5], typical COTS batteries for CubeSat missions are Li-ion cells, whose energy storage capacity may be around 20% of its maximum (at 293 K) when exposed to 253 K.”
BackgroundMarCO: Interplanetary Mission Development on a CubeSat Scale
Schoolcraft, J., Klesh, A., & Werne, T. (2017) · Space Operations: Contributions from the Global Community · doi:10.1007/978-3-319-51941-8_10 · Cited by 80 · cited 1×
“Heaters attached to the battery were used to sustain the temperature, and passive materials were employed to allow heat exchanging with other satellite parts [10,11].”
MethodCurtis, H. D. (2014) · Orbital Mechanics for Engineering Students · doi:10.1016/b978-0-08-097747-8.00006-2 · Cited by 79
A Modular Electrical Power System Architecture for Small Spacecraft
Lim, T. M., Cramer, A. M., Lumpp, J. E., & Rawashdeh, S. A. (2018) · IEEE Transactions on Aerospace and Electronic Systems · doi:10.1109/taes.2018.2803598 · Cited by 69 · cited 1×
“Electrical Model Electrical power system (EPS) architectures can have control in the solar panels, although the so-called direct energy transfer (DET) cannot [23,32].”
BackgroundAnalytical and numerical models for thermal related design of a new pico-satellite
Bonnici, M., Mollicone, P., Fenech, M., & Azzopardi, M. A. (2019) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2019.113908 · Cited by 57 · cited 1×
“Except for the arbitrary value for RTw , these values are approximations of numbers found in the literature—for example, in [19,30,31].”
Result
Cited by
Classification of Contaminated Insulators Using k-Nearest Neighbors Based on Computer Vision
Corso, M. P., Perez, F. L., Stefenon, S. F., Yow, K., Ovejero, R. G., & Leithardt, V. R. Q. (2021) · Computers · doi:10.3390/computers10090112 · Cited by 64
Self-citationReducing temperature swing of space objects with temperature-adaptive solar or radiative coating
Dong, K., Tseng, D., Li, J., Warkander, S., Yao, J., & Wu, J. (2022) · Cell Reports Physical Science · doi:10.1016/j.xcrp.2022.101066 · Cited by 33
Yamagata, M., Wakita, Y., Tsuruda, Y., & Miyata, K. (2022) · Thermal Science and Engineering Progress · doi:10.1016/j.tsep.2022.101601 · Cited by 23
Boonmongkolras, P., Kim, S., Kim, Y. Y., Jeon, N. J., Lee, M. H., & Han, G. S. (2025) · Advanced Functional Materials · doi:10.1002/adfm.202525129 · Cited by 15
Effect of beta angle and contact conductances on the temperature distribution of a 3U CubeSat
Garzón, A., Tami, J. A., Campos-Julca, C. D., & Acero, I. F. (2022) · Thermal Science and Engineering Progress · doi:10.1016/j.tsep.2021.101183 · Cited by 11
Metadata
- Authors
- Vega Martinez, S., Filho, E. M., Seman, L. O., Bezerra, E. A., Nicolau, V. D. P., Ovejero, R. G., & Leithardt, V. R. Q.
- Affiliations
- Department of Electrical Engineering, Federal University of Santa Catarina, Florianópolis, SC 88040-900, Brazil
- Universidade Federal de Santa Catarina (BR)
- Universidade do Vale do Itajaí (BR)
- Universidad de Salamanca (ES)
- Universidade Politécnica de Portalegre (PT)
- Corresponding author
- Seman, Laio Oriel
- ORCID
- Venue
- Applied Sciences
- Publisher
- MDPI AG
- Published
- 2021-02-09
- Volume
- 11
- Issue
- 4
- Pages
- 1554
- ISSN
- 2076-3417 (ISSN-L)
- OpenAlex
- W3128776985
- Semantic Scholar
- cb9a0e00672b748f01b8740055e8638568145a3c
- Cited by
- 18
- References
- 33
- Citations by year
- 2026: 1 · 2025: 4 · 2024: 1 · 2023: 4 · 2022: 7 · 2021: 1
- FWCI
- 1.68
- Type
- journal article
- Language
- en
- Open access
- gold
- dx.doi.org
- Licence
- Locations
- Applied Sciences (publishedVersion, cc-by)
- Portuguese National Funding Agency for Science, Research and Technology (RCAAP Project by FCT) (submittedVersion, other-oa)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (N/A)
- Topics
- Physical Sciences › Engineering › Aerospace Engineering › Spacecraft Design and Technology
- Physical Sciences › Engineering › Automotive Engineering › Battery Modeling and Management
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Photovoltaic System Optimization Techniques
- Keywords
- CubeSat, battery thermal modeling, photovoltaic panel performance, solar irradiance effects, battery thermal management, spacecraft power subsystem
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-12, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-12 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: An Integrated Thermal-Electrical Model for Simulations of Battery Behavior in CubeSats. https://app.cochat.ai/papers/10.3390/app11041554
- The paper
- Vega Martinez, S., Filho, E. M., Seman, L. O., Bezerra, E. A., Nicolau, V. D. P., Ovejero, R. G., & Leithardt, V. R. Q. (2021). An Integrated Thermal-Electrical Model for Simulations of Battery Behavior in CubeSats. Applied Sciences. https://doi.org/10.3390/app11041554
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.