CoChat

Experimental Determination of the Coefficient of Friction on a Screw Joint

Open access
Mascenik, Jozef, Coranic, Tomas · 2022 · Applied Sciences

The DOI matches its Crossref record; 18 of the 18 references it cites were found in a registry or an index.

Abstract

This paper deals with the coefficient of determination of screw connection friction between the thread and the matrix. The coefficient of friction was measured using a laboratory device with an M20 screw connection without any grease and, subsequently, plastic grease was added (CX80 silicone, lithium, and copper grease). When grease is added, the friction in the threads and screw heads is limited and consistently retained. When tightening by torque, which represents the prevailing assembly method in standard screwing practice, only part of the torque is effectively used to create axial force and pre-stress. The rest of the torque is employed in friction suppression between threads and converted into heat. In general, the coefficient of friction depends on diverse factors such as the roughness of the thread surface, the gradient angle of the helix, and the grease properties. The tightening torque represents a primary parameter in the experimental measurements, monitored using a digital torque spanner, and generates an axial force in the screw. Based on the aforementioned parameters, the objective of this paper was to monitor changes in the coefficient of friction between the thread of the screw and the matrix in the case of different grease types. The actual coefficient of friction was calculated through the exponential equation of the torque balance. First measured was the load of the bolted joint without the use of grease, where the average value of the coefficient of friction was 0.44732; this value served as a benchmark for comparison to the measurements with the use of grease. The measurements showed that the value of the friction coefficient was reduced by 30.57% when using lithium grease, by 40.56% when using silicone grease, and by 47.64% when using copper-based grease, making the latter the most suitable for the application. Without appropriate greasing, friction suppression was accompanied by extremely high torques, which resulted in insufficient screw prolongation.

Overview

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.3390/app122311987

Cites

18 of 18 references verified0 citation errors · 0 not checkable

Statistics

Figures

Figure 1 Ratio of the forces for frictionless motion. Figure 1. Ratio of the forces for frictionless motion.
Figure 1 Ratio of the forces for frictionless motion. Figure 1. Ratio of the forces for frictionless motion.CC-BY · From the PDF
Figure 2 Ratio of the forces for motion with friction (tightening). Figure 2. Ratio of the forces for motion with friction (tightening).
Figure 2 Ratio of the forces for motion with friction (tightening). Figure 2. Ratio of the forces for motion with friction (tightening).CC-BY · From the PDF
Figure 3 The stand designed for monitoring bolted joints during controlled loading: I-Basic stru ture; II-membrane force sensor; III-computer; IV-A/D converter; V-tested screw; VI-torq measuring instrument. Figure 3. The stand designed for monitoring bolted joints during controlled loading: I-Basic structure; II-membrane force sensor; III-computer; IV-A/D converter; V-tested screw; VI-torque measuring instrument.
Figure 3 The stand designed for monitoring bolted joints during controlled loading: I-Basic stru ture; II-membrane force sensor; III-computer; IV-A/D converter; V-tested screw; VI-torq measuring instrument. Figure 3. The stand designed for monitoring bolted joints during controlled loading: I-Basic structure; II-membrane force sensor; III-computer; IV-A/D converter; V-tested screw; VI-torque measuring instrument.CC-BY · From the PDF
Figure 4 Emsyst EMS650 converter. Figure 4. Emsyst EMS650 converter. 3.2. Tensometric Force Sensor
Figure 4 Emsyst EMS650 converter. Figure 4. Emsyst EMS650 converter. 3.2. Tensometric Force SensorCC-BY · From the PDF
Figure 5 Tensometric force sensor EMS20. Figure 5. Tensometric force sensor EMS20. Figure 5. Tensometric force sensor EMS20.
Figure 5 Tensometric force sensor EMS20. Figure 5. Tensometric force sensor EMS20. Figure 5. Tensometric force sensor EMS20.CC-BY · From the PDF
Figure 6 Torquemeter WRG3-135 (from 6.8 to 135 Nm). Figure 6. Torquemeter WRG3-135 (from 6.8 to 135 Nm).
Figure 6 Torquemeter WRG3-135 (from 6.8 to 135 Nm). Figure 6. Torquemeter WRG3-135 (from 6.8 to 135 Nm).CC-BY · From the PDF
Figure 7 Visual comparison of the used lubricants. Figure 7. Visual comparison of the used lubricants.
Figure 7 Visual comparison of the used lubricants. Figure 7. Visual comparison of the used lubricants.CC-BY · From the PDF
Figure 8 Dependence of the emerging axial force FO on time from the EMS Center software. Figure 8. Dependence of the emerging axial force FO on time from the EMS Center software.
Figure 8 Dependence of the emerging axial force FO on time from the EMS Center software. Figure 8. Dependence of the emerging axial force FO on time from the EMS Center software.CC-BY · From the PDF
Image 9
CC-BY · From the PDF
Figure 10 Dependence of the emerging force FOL on time. Figure 10. Dependence of the emerging force FOL on time.
Figure 10 Dependence of the emerging force FOL on time. Figure 10. Dependence of the emerging force FOL on time.CC-BY · From the PDF
Image 11
CC-BY · From the PDF
Figure 12 Dependence of the loading tightening torque on the emerging axial force with and without lubricating grease. Figure 12. Dependence of the loading tightening torque on the emerging axial force with and without lubricating grease.
Figure 12 Dependence of the loading tightening torque on the emerging axial force with and without lubricating grease. Figure 12. Dependence of the loading tightening torque on the emerging axial force with and without lubricating grease.CC-BY · From the PDF
Figure 13 Dependence of the tightening torques on the actual calculated coefficients of friction with and without lubricating grease. Figure 13. Dependence of the tightening torques on the actual calculated coefficients of friction with and without lubricating grease.
Figure 13 Dependence of the tightening torques on the actual calculated coefficients of friction with and without lubricating grease. Figure 13. Dependence of the tightening torques on the actual calculated coefficients of friction with and without lubricating grease.CC-BY · From the PDF

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Research works printed but not linked: 3

  1. 7. Appl. Sci. 2022, 12, 11987
  2. 11. Trojanowska, J.; Paj ąk, E. Using the Theory of Constraints to Production Processes Improvement. In Proceedings of the 7th International Conference of DAAAM Baltic Industrial Engineering, Tallinn, Estonia, 22-24 April 2010; Volume 1, pp. 322-327.
  3. 18. Straka, L.; Panda, A. Verification of the non-contact method of measuring roughness parameters on surface machined by WEDM technology. Stud. I Mater. 2021, 41, 32-37.

Cited by

See all 13

Metadata

Authors
Mascenik, J., & Coranic, T.
Affiliations
Department of Design and Monitoring of Technical Systems, Faculty of Manufacturing Technologies with a Seat in Presov, Technical University of Kosice, Bayerova 1, 080 01 Presov, Slovakia
Venue
Applied Sciences
Publisher
MDPI AG
Published
2022-11-23
Volume
12
Issue
23
Pages
11987
ISSN
2076-3417 (ISSN-L)
OpenAlex
W4310024326
Cited by
13
References
18
Citations by year
2025: 3 · 2024: 4 · 2023: 6
FWCI
1.25
Type
journal article
Language
en
Open access
Locations
  • Applied Sciences (publishedVersion, cc-by)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
Funders
  • Slovak Ministry of Education within project KEGA (017TUKE-4/2021, APVV-18-0316)
  • Slovak Research and Development Agency (017TUKE-4/2021, APVV-18-0316)
Topics
  • Physical Sciences › Engineering › Mechanical Engineering › Engineering Structural Analysis Methods
  • Physical Sciences › Engineering › Mechanical Engineering › Tribology and Lubrication Engineering
  • Physical Sciences › Engineering › Mechanical Engineering › Bladed Disk Vibration Dynamics
Keywords
friction coefficient, screw joints, threaded connections, bolted joints, lubrication, lubricating greases, torque tightening, axial force, prestressing, silicone grease, lithium grease, friction torque

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.