CoChat

Poka Yoke in Smart Production Systems with Pick-to-Light Implementation to Increase Efficiency

Open access
Trojanowska, Justyna, Husár, Jozef, Hrehova, Stella, Knapčíková, Lucia · 2023 · Applied Sciences

The DOI matches its Crossref record; 33 of the 34 references it cites were found in a registry or an index; 13 of the 19 sources its claims cite were checked for support.

Abstract

Pick-to-light implementation based on Poka-Yoke principles in smart production systems.

Overview

CoChat Summary

TL;DR

The paper presents a custom modular Pick-to-Light (PTL) system based on Poka Yoke, tested in a small company with 30 employees assembling a model extruder. It reports assembly-time reductions of 7–35% depending on the measure/worker and a 35% reduction in error rate after PTL introduction.

Key findings

  • Error rate: 30 workers made 34 errors while assembling 10 extruders before PTL and 22 errors after PTL, a 35% decrease.
  • One-piece assembly: greatest time reduction was worker 14, from 145 s to 95 s (35%); smallest was 11% (worker 9: 126 s to 113 s; worker 25: 140 s to 125 s).
  • Production batch: greatest saving was 33% for worker 14; smallest was 7% for worker 16, from 859 s to 798 s. Average one-component assembly fell from 63.8 s to 57.4 s (~11%), and average 10-piece batch assembly fell from 789.76 s to 639.6 s (~20%).
  • Preparatory operations also improved: component/tool preparation from 24.7 s to 22.63 s, training from 11.16 s to 8.8 s, studying the procedure by more than 50% (average 29.67 s to 14.43 s), connection check from 4.43 s to 3.97 s, and storage from 6.43 s to 4.33 s. All tested workers said they liked the PTL introduction and could imagine its deployment.

Methods

  • Design combined a literature review with a case study in a small company; the model part was an extruder with a motor for 3D printers, composed of 8 basic parts and a six-step assembly procedure.
  • The test had two parts: assembly without the PTL device, then assembly with the PTL device. The sample was 30 employees (14 male, 16 female; ages 21–60 in Table 1, described as 22–57 in the conclusions).
  • Each employee repeated the assembly 10 times; the main compared parameters were one-piece cycle length, production-batch length, error occurrence, and employee feeling.

Limitations

  • Stated: the paper says it is difficult to provide exact advantages and disadvantages of the PTL system by socio-demographic factors because these vary by operation and user group; some workers reported after one test that the device seemed small and difficult to operate.
  • Evident from the text: the study is a single small-company case with 30 participants, uses a simulated training workplace and one model component, and reports before/after comparisons without a control group or statistical testing, so generalizability is limited.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.3390/app132111715

Cites

33 of 33 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Figures

Figure 1 The Poka Yoke principle [4]. Figure 1. The Poka Yoke principle [4].
Figure 1 The Poka Yoke principle [4]. Figure 1. The Poka Yoke principle [4].CC-BY · From the PDF
Figure 2 Literature review of Poka Yoke (authors own processing). Figure 2. Literature review of Poka Yoke (authors own processing).
Figure 2 Literature review of Poka Yoke (authors own processing). Figure 2. Literature review of Poka Yoke (authors own processing).CC-BY · From the PDF
Figure 3 Pick-to-Light system architecture. Figure 3. Pick-to-Light system architecture.
Figure 3 Pick-to-Light system architecture. Figure 3. Pick-to-Light system architecture.CC-BY · From the PDF
Figure 4 Constructed Pick-to-Light device labelled Spider 1. Figure 4. Constructed Pick-to-Light device labelled Spider 1.
Figure 4 Constructed Pick-to-Light device labelled Spider 1. Figure 4. Constructed Pick-to-Light device labelled Spider 1.CC-BY · From the PDF
Figure 5 Extruder with the motor in unfolded and folded state. Figure 5. Extruder with the motor in unfolded and folded state.
Figure 5 Extruder with the motor in unfolded and folded state. Figure 5. Extruder with the motor in unfolded and folded state.CC-BY · From the PDF
Figure 6 Assembly workplace without PTL. Figure 6. Assembly workplace without PTL.
Figure 6 Assembly workplace without PTL. Figure 6. Assembly workplace without PTL.CC-BY · From the PDF
Figure 7 Assembly workplace with PTL. Figure 7. Assembly workplace with PTL.
Figure 7 Assembly workplace with PTL. Figure 7. Assembly workplace with PTL.CC-BY · From the PDF
Figure 8 Comparison of assembly times before and after the PTL introduction for the 1 piece. Figure 8. Comparison of assembly times before and after the PTL introduction for the 1 piece.
Figure 8 Comparison of assembly times before and after the PTL introduction for the 1 piece. Figure 8. Comparison of assembly times before and after the PTL introduction for the 1 piece.CC-BY · From the PDF
Figure 9 Comparison of assembly times before and after the PTL introduction for the production batch. Figure 9. Comparison of assembly times before and after the PTL introduction for the production batch.
Figure 9 Comparison of assembly times before and after the PTL introduction for the production batch. Figure 9. Comparison of assembly times before and after the PTL introduction for the production batch.CC-BY · From the PDF

Verification

Claims the paper makes

7 Valid · 5 Not valid · 2 Not checked · 53 Own results and interpretations

24 more claims

Create a free account to see all 67 claims and to verify the 1 reference still open.

See all claims — free account
  • Probably not a substantial claim. 28
  • It may state two separate claims as one. 16

Create a free account to see these claims.

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

Each contradiction between two passages listed here was confirmed by an independent check.

2 of 2

Citations

Cites

Show all 33 references

Research works printed but not linked: 4

  1. Pankaj, 2018, Review Paper on “Productivity Improvement by using Poka-Yoke”, Int. Res. J. Eng. Technol., 5, 761
  2. Vinayagasundaram, 2018, Implementation of Zero Defect through POKA YOKE Approaches in the Assembly Line of Compressor Manufacturing Industry, Int. J. Pure Appl. Math., 119, 2319
  3. Hirano, H., and Shibun, N.K. (1988). POKA-YOKE Improving Product Quality by Preventing Defects, Productivity Press.
  4. Saleh, 2022, The Role of Empovering Leadership in Enhancing the Adaptive Penformance of Employees, Acta Technol., 8, 1

Cited by

See all 23

Metadata

Authors
Trojanowska, J., Husár, J., Hrehova, S., & Knapčíková, L.
Affiliations
  • Poznań University of Technology (PL)
  • Technical University of Košice (SK)
  • Department of Industrial Engineering and Informatics, Faculty of Manufacturing Technologies, Technical University of Košice, Bayerova 1, 08001 Prešov, Slovakia
Corresponding author
Trojanowska, Justyna
Venue
Applied Sciences
Publisher
MDPI AG
Published
2023-10-26
Volume
13
Issue
21
Pages
11715
ISSN
2076-3417 (ISSN-L)
OpenAlex
W4388201638
Cited by
23
References
34
Citations by year
2026: 6 · 2025: 10 · 2024: 7
FWCI
3.05
Type
journal article
Language
en
Open access
Locations
  • Applied Sciences (publishedVersion, cc-by)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
Funders
  • Ministry of Education and Science of Poland (0613/SBAD/4821, KEGA 038TUKE-4/2022)
  • the Ministry of Education, Science, Research and Sport of the Slovak Republic (0613/SBAD/4821, KEGA 038TUKE-4/2022)
Topics
  • Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Manufacturing Process and Optimization
  • Social Sciences › Business, Management and Accounting › Strategy and Management › Management and Optimization Techniques
  • Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Advanced Manufacturing and Logistics Optimization
Keywords
poka-yoke, pick-to-light, assembly guidance, product assembly, assembly error reduction, assembly time reduction, smart manufacturing, human-machine interaction

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

The claim verdicts this report counts are experimental: their accuracy is not yet measured.

A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).

A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Cited sources are checked with a language model’s help (gpt-6-sol).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Poka Yoke in Smart Production Systems with Pick-to-Light Implementation to Increase Efficiency. https://app.cochat.ai/papers/10.3390/app132111715
The paper
Trojanowska, J., Husár, J., Hrehova, S., & Knapčíková, L. (2023). Poka Yoke in Smart Production Systems with Pick-to-Light Implementation to Increase Efficiency. Applied Sciences. https://doi.org/10.3390/app132111715

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.