The DOI matches its Crossref record; 45 of the 47 references it cites were found in a registry or an index; 3 of the 38 sources its claims cite were checked for support.
Characterization of Hybrid-nano/Paraffin Organic Phase Change Material for Thermal Energy Storage Applications in Solar Thermal Systems
Open accessAbstract
In this work, the experimental investigations were piloted to study the influence of hybrid nanoparticles containing SiO2 and CeO2 nanoparticles on thermo-physical characteristics of the paraffin-based phase change material (PCM). Initially, the hybrid nanoparticles were prepared by blending equal mass of SiO2 and CeO2 nanoparticles. The hybrid-nano/paraffin (HnP) samples were prepared by cautiously dispersing 0, 0.5, 1.0, and 2.0 percentage mass of hybrid nanoparticles inside the paraffin, respectively. The synthesized samples were examined under different instruments such as field emission scanning electron microscope (FESEM), Fourier transform infrared spectrometer (FTIR), differential scanning calorimetry (DSC), thermogravimetric analyzer (TGA), and thermal properties analyzer to ascertain the influence of hybrid nanoparticles on thermo-physical characteristics of the prepared samples. The obtained experimental results proved that the hybrid nanoparticles were uniformly diffused in the paraffin matrix without affecting the chemical arrangement of paraffin molecules. Prominently, the relative thermal stability and relative thermal conductivity of the paraffin were synergistically enriched up to 115.49% and 165.56%, respectively, when dispersing hybrid nanoparticles within paraffin. Furthermore, the hybrid nanoparticles appropriately amended the melting and crystallization point of the paraffin to reduce its supercooling, and the maximum reduction in supercooling was ascertained as 35.81%. The comprehensive studies indicated that the paraffin diffused with SiO2 and CeO2 hybrid nanoparticles at 1.0 mass percentage would yield a better outcome compared to the next higher mass fractions without much diminishing the latent heat of paraffin. Hence, it is recommended to utilize the hybrid-nano/paraffin with 1.0 mass fraction of the aforementioned hybrid nanoparticles for effectively augmenting the thermal energy capacity of low-temperature solar thermal systems.
Overview
CoChat Summary
TL;DR
Hybrid SiO₂/CeO₂ nanoparticles were dispersed in paraffin at 0, 0.5, 1.0, and 2.0 mass% to improve thermal energy storage properties for low-temperature solar thermal systems. The 1.0 mass% hybrid-nano/paraffin gave the best balance, reducing supercooling by 35.81% while avoiding the larger latent-heat penalty seen at 2.0 mass%.
Key findings
- Hybrid nanoparticles dispersed uniformly in paraffin without altering paraffin’s chemical structure; FESEM showed agglomeration only in the 2.0 HnP sample.
- Relative thermal stability and relative thermal conductivity were enriched up to 115.49% and 165.56%, respectively. Thermal conductivity rose from 0.18 W/mK for pure paraffin to 0.231, 0.26, and 0.298 W/mK at 0.5%, 1.0%, and 2.0% hybrid nanoparticles.
- Supercooling was reduced most at 1.0 HnP: 4.32 °C versus 6.73 °C for pure paraffin, a 35.81% reduction. Latent heat decreased with nanoparticle loading; at 2.0 HnP the reduction was 20.68% during melting and 29.12% during freezing.
- The paper recommends 1.0 mass% hybrid-nano/paraffin as the optimum for low-temperature solar thermal systems, because it reduces supercooling without much compromising latent heat compared with 2.0 mass%.
Methods
- Commercial-grade paraffin wax was used as the base PCM, with equal-mass SiO₂ and CeO₂ nanoparticles (mean diameter 25 nm each). Samples were prepared at 0%, 0.5%, 1.0%, and 2.0% total hybrid nanoparticle mass via melt mixing on a magnetic stirrer for 2 h followed by 60 min ultrasonication, without surfactant.
- Characterization included Zetasizer for nanoparticle size, FESEM for dispersion, FTIR for chemical stability, DSC for melting/crystallization/supercooling/latent heat (5 °C/min, 30–80 °C, nitrogen), TGA for thermal stability (5.5 mg samples, 10 °C/min, 30–450 °C, nitrogen), and a KD2 Pro thermal properties analyzer for thermal conductivity.
- Thermal conductivity data were fitted with the correlation k = 0.18125 + 0.10435x − 0.02309x², with a correlation coefficient of 0.99741.
Limitations
- The paper does not state a dedicated limitations section. Evident from the text: only four mass fractions up to 2.0% were tested, and the 2.0 HnP sample showed agglomeration, limiting conclusions above that loading.
- No surfactant was used, and the study reports only laboratory-scale thermo-physical characterization; no integrated solar thermal system performance or long-term cycling/durability test is reported, despite the claim that the composites are feasible for repeating cycles.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
3 Valid · 0 Not valid · 28 Not checked · 53 Own results and interpretations
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“More than 50% of both nanoparticles are in the size between 15 nm and 30 nm, which was specified by the supplier.”
§ Characterization of Hybrid-nano/Paraffin Organic Phase Change Material for Thermal Energy Storage Applications in Solar Thermal Systems > 3.1. Validation of Nanoparticle Size and Investigating Surface Morphology of the HnP Samples
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Prominently, the relative thermal stability and relative thermal conductivity of the paraffin were synergistically enriched up to 115.49% and 165.56%, respectively, when dispersing hybrid nanoparticles within paraffin.”
§ Characterization of Hybrid-nano/Paraffin Organic Phase Change Material for Thermal Energy Storage Applications in Solar Thermal Systems > Abstract
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“However, in this present investigation, the dispersion was found to have better physical interaction without substantial agglomeration in all the prepared samples, except for the sample having 2.0% of hybrid nanoparticles (Figure 3d).”
§ Characterization of Hybrid-nano/Paraffin Organic Phase Change Material for Thermal Energy Storage Applications in Solar Thermal Systems > 3.2. Chemical Stability of the HnP Samples
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“appropriately amended the melting and crystallization point of the paraffin to reduce its supercooling, and the maximum reduction in supercooling was ascertained as 35.81%.”
§ Characterization of Hybrid-nano/Paraffin Organic Phase Change Material for Thermal Energy Storage Applications in Solar Thermal Systems > Abstract
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Prominently, the relative thermal stability and relative thermal conductivity of the paraffin were synergistically enriched up to 115.49% and 165.56%, respectively, when dispersing hybrid nanoparticles within paraffin.”
§ Characterization of Hybrid-nano/Paraffin Organic Phase Change Material for Thermal Energy Storage Applications in Solar Thermal Systems > Abstract
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
44 more claims
Create a free account to see all 84 claims and to verify the 1 reference still open.
- Probably not a substantial claim. 14
- It may state two separate claims as one. 24
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“The thermal conductivity improved greatly up to 1% NPs and minimally above that percentage, as can be seen in Figure 8.”
From Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review (2021) · cites this paper as [49]
Experimental — accuracy not yet measuredThe cited source says what the claim attributes to it.
In the citing paper
“At 2%, the particles begin to agglomerate, but they were evenly distributed up to that point.”
From Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review (2021) · cites this paper as [49]
The cited source says what the claim attributes to it.
In the citing paper
“The NPs reduced the difference between the melting and solidification temperatures of the paraffin and delayed thermal decomposition.”
From Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review (2021) · cites this paper as [49]
The cited source says what the claim attributes to it.
In the citing paper
“It was concluded that 1% NPs was the best amount for enhancement [49].”
From Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review (2021) · cites this paper as [49]
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
“| 1.0 HnP | 62.81 | 133.7 | 58.79 | 127.8 | 4.32 |”
§ Characterization of Hybrid-nano/Paraffin Organic Phase Change Material for Thermal Energy Storage Applications in Solar Thermal Systems > 4. Conclusions
Reported 4.32 · recomputed 4.02
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
“It can be visibly seen that the degradation of the paraffin was prominently delayed by adding 2.0% mass of nanoparticle, which is 21 °C greater than that of pure paraffin.”
§ Characterization of Hybrid-nano/Paraffin Organic Phase Change Material for Thermal Energy Storage Applications in Solar Thermal Systems > 3.4. Thermal Stability and Thermal Conductivity of the HnP Samples
Reported 21 · recomputed 22
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
“| 0.5 HnP | 63.27 | 136.1 | 57.06 | 129.4 | 5.67 |”
§ Characterization of Hybrid-nano/Paraffin Organic Phase Change Material for Thermal Energy Storage Applications in Solar Thermal Systems > 4. Conclusions
Reported 5.67 · recomputed 6.21
Citations
Cites
Recent developments in phase change materials for energy storage applications: A review
Nazir, H., Batool, M., Bolivar Osorio, F. J., Isaza-Ruiz, M., Xu, X., Vignarooban, K., Phelan, P., Inamuddin, & Kannan, A. M. (2019) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.09.126 · Cited by 1,522 · cited 1×
“A broad number of phase-changing materials (PCMs) including organic and inorganic compounds have been reviewed and deliberated [5,6].”
BackgroundLin, Y., Jia, Y., Alva, G., & Fang, G. (2018) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2017.10.002 · Cited by 910 · cited 13×
“Relatively, a study on thermal storage behavior of paraffin-based PCM reported that by infusing a hybrid-nano containing CuO and TiO2 nanoparticles within the paraffin had drastically suppressed cooling and heating rates owing to their collegial behavior [25].”
MethodInfluentialFan, L.-W., Fang, X., Wang, X., Zeng, Y., Xiao, Y.-Q., Yu, Z.-T., Xu, X., Hu, Y.-C., & Cen, K.-F. (2013) · Applied Energy · doi:10.1016/j.apenergy.2013.04.043 · Cited by 478 · cited 2×
“Later, a substantial rise was observed in the samples, which are predominantly due to the solid to liquid phase conversion, and this large significant peak determines the thermal storage capability of the PCM in the form of latent capacity [39].”
BackgroundA nano-graphite/paraffin phase change material with high thermal conductivity
Li, M. (2013) · Applied Energy · doi:10.1016/j.apenergy.2013.01.031 · Cited by 421 · cited 3×
“Li [8] admitted that relative thermal conductivity was amplified to a greater extent when a 10% nano-graphite was dispersed in paraffin.”
BackgroundAmin, M., Putra, N., Kosasih, E. A., Prawiro, E., Luanto, R. A., & Mahlia, T. M. I. (2017) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2016.10.085 · Cited by 370 · cited 1×
“On the other hand, the agglomeration tends to be formed while upsurging the mass of nanoparticles, which may be primarily ascribed to the Van der Walls forces among the nanoparticles complemented with the Brownian motion [35].”
BackgroundGhosh, A. (2020) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.123343 · Cited by 332 · cited 1×
“Recently, several works have been carried out by a quite a few researchers to address this problem by integrating the solar thermal systems with suitable thermal energy storage material [3].”
BackgroundSelf-citationEvaluation of copper nanoparticles–Paraffin wax compositions for solar thermal energy storage
Lin, S. C., & Al-Kayiem, H. H. (2016) · Solar Energy · doi:10.1016/j.solener.2016.03.004 · Cited by 323 · cited 8×
“The differential sc i l ri tr ( S ) analysis was conducted on all the HnP samples at the rate of 5 ◦C per minute in a nitrogen atmosphere and the temper ture w s programm d Energies 2020, 13, 5079 8 of 15 between 30 ◦C and 80 ◦C considering the phase transition temperature of paraffin, as endorsed by Lin and Al-Kayiem…”
BackgroundMethodInfluentialHamid, K. A., Azmi, W. H., Nabil, M. F., Mamat, R., & Sharma, K. V. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2017.09.087 · Cited by 310
Jiang, X., Luo, R., Peng, F., Fang, Y., Akiyama, T., & Wang, S. (2015) · Applied Energy · doi:10.1016/j.apenergy.2014.09.028 · Cited by 279
Sharma, R. K., Ganesan, P., Tyagi, V. V., Metselaar, H. S. C., & Sandaran, S. C. (2016) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2016.01.130 · Cited by 265 · cited 1×
“[9] conducted a study on palmitic acid by adding TiO2 nanoparticles in four mass ratios such as 0.”
Background
Cited by
Jayathunga, D. S., Karunathilake, H. P., Narayana, M., & Witharana, S. (2024) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2023.113904 · Cited by 298
Nundy, S., Mesloub, A., Alsolami, B. M., & Ghosh, A. (2021) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2021.126854 · Cited by 248
Self-citationYang, Z. L., Walvekar, R., Wong, W. P., Sharma, R. K., Dharaskar, S., & Khalid, M. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.111329 · Cited by 225
Interfacial bonding mechanisms of natural fibre-matrix composites: An overview
Mohammed, M., Rasidi, M., Mohammed, A., Rahman, R., Osman, A., Adam, T., Betar, B., & Dahham, O. (2022) · BioResources · doi:10.15376/biores.17.4.mohammed · Cited by 175
Investigating a single slope solar still with a nano-phase change material
Manoj Kumar, P., Sudarvizhi, D., Prakash, K. B., Anupradeepa, A. M., Boomiha Raj, S., Shanmathi, S., Sumithra, K., & Surya, S. (2021) · Materials Today: Proceedings · doi:10.1016/j.matpr.2020.12.804 · Cited by 159
Self-citation
Metadata
- Authors
- Pasupathi, M. K., Alagar, K., P, M. J. S., M.M, M., & Aritra, G.
- Affiliations
- Department of Mechanical Engineering, KPR Institute of Engineering and Technology, Coimbatore 641407, India
- Department of Electrical and Electronics Engineering, KPR Institute of Engineering and Technology, Coimbatore 641407, India
- Department of Mechanical Engineering, Audisankara College of Engineering & Technology, Gudur 524101, India
- Department of Mechanical Engineering, Jansons Institute of Technology, Coimbatore 641659, India
- Environment and Sustainability Institute, University of Exeter, Penryn, Cornwall TR10 9FE, UK
- Venue
- Energies
- Publisher
- MDPI AG
- Published
- 2020-09-29
- Volume
- 13
- Issue
- 19
- Pages
- 5079
- ISSN
- 1996-1073 (ISSN-L)
- OpenAlex
- W3088463453
- Cited by
- 171
- References
- 47
- Citations by year
- 2026: 16 · 2025: 13 · 2024: 17 · 2023: 19 · 2022: 44 · 2021: 58 · 2020: 4
- FWCI
- 15.37
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Energies (publishedVersion, cc-by)
- RePEc: Research Papers in Economics (submittedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Phase Change Materials Research
- Physical Sciences › Engineering › Mechanical Engineering › Adsorption and Cooling Systems
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Solar Thermal and Photovoltaic Systems
- Keywords
- hybrid nanostructures, alkanes, phase change materials, thermal energy storage, solar thermal systems, silica nanoparticles, cerium oxide nanoparticles, thermal conductivity, thermal stability, supercooling, latent heat
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-09-28, under version 3 of the claim definition (prompt extract-v3).
A second model labelled each claim on 2026-09-28 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Characterization of Hybrid-nano/Paraffin Organic Phase Change Material for Thermal Energy Storage Applications in Solar Thermal Systems. https://app.cochat.ai/papers/10.3390/en13195079
- The paper
- Pasupathi, M. K., Alagar, K., P, M. J. S., M.M, M., & Aritra, G. (2020). Characterization of Hybrid-nano/Paraffin Organic Phase Change Material for Thermal Energy Storage Applications in Solar Thermal Systems. Energies. https://doi.org/10.3390/en13195079
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.