The DOI matches its Crossref record; 94 of the 94 references it cites were found in a registry or an index; 110 of the 346 sources its claims cite were checked for support.
Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review
Open accessAbstract
Latent heat thermal energy storage systems (LHTES) are useful for solar energy storage and many other applications, but there is an issue with phase change materials (PCMs) having low thermal conductivity. This can be enhanced with fins, metal foam, heat pipes, multiple PCMs, and nanoparticles (NPs). This paper reviews nano-enhanced PCM (NePCM) alone and with additional enhancements. Low, middle, and high temperature PCM are classified, and the achievements and limitations of works are assessed. The review is categorized based upon enhancements: solely NPs, NPs and fins, NPs and heat pipes, NPs with highly conductive porous materials, NPs and multiple PCMs, and nano-encapsulated PCMs. Both experimental and numerical methods are considered, focusing on how well NPs enhanced the system. Generally, NPs have been proven to enhance PCM, with some types more effective than others. Middle and high temperatures are lacking compared to low temperature, as well as combined enhancement studies. Al2O3, copper, and carbon are some of the most studied NP materials, and paraffin PCM is the most common by far. Some studies found NPs to be insignificant in comparison to other enhancements, but many others found them to be beneficial. This article also suggests future work for NePCM and LHTES systems.
Overview
CoChat Summary
TL;DR
This review surveys nano-enhanced phase change materials (NePCM) for latent heat thermal energy storage, covering nanoparticles used alone and combined with fins, heat pipes, porous foams, multiple PCMs, and nano-encapsulation. It concludes that nanoparticles generally enhance PCM performance, but the "best" nanoparticle is highly situational and depends on the base PCM, melting temperature, and companion enhancement.
Key findings
- Nanoparticles were effective in nearly every reviewed case, but some studies found them weak relative to other enhancements (e.g., metal foam, heat pipes, fins). Paraffin is by far the most studied PCM, and Al₂O₃, copper, and carbon are the most studied nanoparticle materials.
- Comparative nanoparticle studies report wide-ranging thermal conductivity gains at 5% mass fraction in paraffin (A82): MWCNTs 26.7%, GNPs 154.9%, ZnO 2.6%, TiO₂ 3.6%, Al₂O₃ 6.5%, and MgO 8.4% [42]. Javadi et al. found Cu best and SiO₂ worst, with 0.2 volume fraction raising thermal conductivity up to 55% and "blade"-shaped particles most efficient [45].
- Specific quantitative outcomes cited: Algarni et al. reported a 32% overall efficiency enhancement in an evacuated tube solar collector with Cu NePCM [39]; Murugan et al. found melting time lowest at 0.3 wt% MWCNTs (−30%) and solidification lowest at 0.9 wt% (−42.2%) [43]; Mahdavi et al. reduced full charge time from 2100 min to 341 min with four heat pipes and cut discharging time by 96%, at a 14% storage-capacity penalty [82]; Ma et al. raised paraffin thermal conductivity to 1.95 W/mK with Cu at 1.9% mass fraction versus 0.216 W/mK unenhanced and 1.073 W/mK with expanded graphite [90]; Yu et al. reported SiO₂ nanoparticles increasing thermal conductivity 23.2× in solid and 9.2× in liquid state [92].
- Middle- and high-temperature NePCM studies are scarce compared with low-temperature work, and combined-enhancement studies (especially NPs with multiple PCMs) are limited; only one study combining multiple PCMs and NPs was identified [93].
Methods
- Narrative literature review of experimental and numerical studies on NePCM in LHTES systems, organized by enhancement category: nanoparticles alone, NPs with fins, NPs with heat pipes, NPs with highly conductive porous materials, NPs with multiple PCMs, and nano-encapsulated PCMs.
- PCMs are classified as low (<120 °C), middle (120–300 °C), and high (>300 °C) melting temperature following Huang et al. [8]; studies are summarized in five tables (Tables 1–5) covering PCM, nanoparticle type, phase-change process, study type, and result.
- No meta-analysis or pooled quantitative synthesis is performed; findings are reported study by study.
Limitations
- Stated by the paper: middle- and high-temperature NePCM research is lacking relative to low-temperature work; combined enhancement studies are fewer than NP-alone studies; most NP-plus-fin studies are numerical, with experimental work needed; nanoparticle sinking/agglomeration and the resulting inconsistency are unresolved; and there is no strong pattern identifying the best nanoparticle across studies.
- Evident from the text: as a narrative review it provides no standardized comparison metric, so cross-study quantitative claims (e.g., percentage improvements) come from heterogeneous setups and are not directly comparable; several summarized results are drawn from conference proceedings and figures rather than uniform primary data.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures
![Figure 1 ( a ) Sensible heat, ( b ) latent heat, ( c ) thermo-chemical thermal energy storage systems (Copyright 2015 Gracia and Cabeza) [4]. Figure 1. ( a ) Sensible heat, ( b ) latent heat, ( c ) thermo-chemical thermal energy storage systems (Copyright 2015 Gracia and Cabeza) [4].](https://figures.cochat.ai/paper-figures/d8901e9309884186b909a10f81404472/nano-enhanced-phase-change-materials-in-latent-heat-thermal-energy-storage-figure-1.png)

![Figure 3 Heat pipe network schematic from Mahdavi et al. (Copyright 2016 Elsevier) [13]. Figure 3. Heat pipe network schematic from Mahdavi et al. (Copyright 2016 Elsevier) [13].](https://figures.cochat.ai/paper-figures/0ac8bbca06da46078d36a5f8254f3b1d/nano-enhanced-phase-change-materials-in-latent-heat-thermal-energy-storage-figure-3.png)
![Figure 4 LHTES system assisted by finned heat pipes (Copyright 2016 Elsevier) [16]. Figure 4. LHTES system assisted by finned heat pipes (Copyright 2016 Elsevier) [16].](https://figures.cochat.ai/paper-figures/0f04a92162694e479e8423af88716e2f/nano-enhanced-phase-change-materials-in-latent-heat-thermal-energy-storage-figure-4.png)
![Figure 5 LHTES system configuration for the study by Akhmetov et al. (Copyright 2019 International Solar Energy Society) [31]. Figure 5. LHTES system configuration for the study by Akhmetov et al. (Copyright 2019 International Solar Energy Society) [31].](https://figures.cochat.ai/paper-figures/5f6d1eb8ce6a4df58266ed3dea5bc6d3/nano-enhanced-phase-change-materials-in-latent-heat-thermal-energy-storage-figure-5.png)
![Figure 6 The graphs show little/no improvement with the addition of NPs in the Farsani et al. study (Copyright 2017 Elsevier) [34]. A 2017 numerical study by Elbahjaoui and El Qarnia used paraffin enhanced with Figure 6. ( a ) liquid fraction, ( b ) average dimensionless temperature, ( c ) maximum dimensionless tempera-ture, and ( d ) average Nusselt number in in the Farsani et al. study (Copyright 2017 Elsevier) [34].](https://figures.cochat.ai/paper-figures/caabea35380441aa805edd628dd661d7/nano-enhanced-phase-change-materials-in-latent-heat-thermal-energy-storage-figure-6.png)
![Figure 7 Liquid fractions of the different NePCMs tested over time by Javadi et al. (Copyright 2020 Javadi et al. https://creativecommons.org/licenses/by/4.0/) accessed on 18 June 2021 [45]. Figure 7. Liquid fractions of the different NePCMs tested over time by Javadi et al. (Copyright 2020 Javadi et al. https://creativecommons.org/licenses/by/4.0/) accessed on 18 June 2021 [45].](https://figures.cochat.ai/paper-figures/393ae60678174edaba6b0d0070ffad93/nano-enhanced-phase-change-materials-in-latent-heat-thermal-energy-storage-figure-7.png)
![Figure 8 The relative enhancement in thermal conductivity with the addition of NPs (Copyright 2020 Pasupathi et al. https://creativecommons.org/licenses/by/4.0/legalcode) accessed on 18 June 2021 [49]. Figure 8. The relative enhancement in thermal conductivity with the addition of NPs (Copyright 2020 Pasupathi et al. https://creativecommons.org/licenses/by/4.0/legalcode) accessed on 18 June 2021 [49].](https://figures.cochat.ai/paper-figures/17054fdc376a41c88663f713c094d801/nano-enhanced-phase-change-materials-in-latent-heat-thermal-energy-storage-figure-8.png)
![Figure 9 SEM images of ( a ) Silicon carbide, ( b ) Silver, ( c ) Pure paraffin wax, ( d ) Paraffin-SiC composite, and ( e ) Paraffin-Ag composite from Maher et al. (Copyright 2020 Elsevier) [52]. Figure 9. SEM images of ( a ) Silicon carbide, ( b ) Silver, ( c ) Pure paraffin wax, ( d ) Paraffin-SiC composite, and ( e ) Paraffin-Ag composite from Maher et al. (Copyright 2020 Elsevier) [52].](https://figures.cochat.ai/paper-figures/76ddf524bdbe4de6b011f450bc3ba406/nano-enhanced-phase-change-materials-in-latent-heat-thermal-energy-storage-figure-9.png)
![Figure 10 Fin configurations for the three cases studied by Hajizadeh et al. (Copyright 2020 Elsevier) [75]. Figure 10. Fin configurations for the three cases studied by Hajizadeh et al. (Copyright 2020 Elsevier) [75].](https://figures.cochat.ai/paper-figures/5aa3de0480414b80946862522bcd71d3/nano-enhanced-phase-change-materials-in-latent-heat-thermal-energy-storage-figure-10.png)


![Figure 13 The PCM liquid fractions at three different times with the different numbers of heat pipes. (Copyright 2019 Elsevier) [82]. Figure 13. The PCM liquid fractions at three different times with the different numbers of heat pipes. (Copyright 2019 Elsevier) [82].](https://figures.cochat.ai/paper-figures/8d0f2b208d47455bac56ed0ff45a9ddd/nano-enhanced-phase-change-materials-in-latent-heat-thermal-energy-storage-figure-13.png)
Verification
Claims the paper makes
95 Valid · 9 Not valid · 235 Not checked · 58 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“The higher thermal storage density, large array of PCMs, and nearly isothermal behavior of LHTES systems (shown in Figure 1b) make them more convenient than the other methods [2].”
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 1. Introduction to Latent Heat Thermal Energy Storage
What the sources say
- Supportedcites [2] Khan, 2016, A review of performance enhancement of PCM based latent heat storage system within the context of materials, thermal stability and compatibility, Energy Convers. Manag. source
The Introduction says LHS systems offer “almost isothermal operation of thermal storage/retrieval.” Section 4 likewise describes heat storage as a “nearly isothermal process.” (LLM, conf=0.95)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“The higher thermal storage density, large array of PCMs, and nearly isothermal behavior of LHTES systems (shown in Figure 1b) make them more convenient than the other methods [2].”
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 1. Introduction to Latent Heat Thermal Energy Storage
What the sources say
- Supportedcites [2] Khan, 2016, A review of performance enhancement of PCM based latent heat storage system within the context of materials, thermal stability and compatibility, Energy Convers. Manag. source
The Introduction identifies higher thermal storage density as an advantage of latent heat storage and compares the greater mass of rock (SHS) needed to store the same energy as several PCMs (LHS). It also identifies a wide range of PCMs and nearly isothermal operation, the other advantages in the citing sentence. (LLM, conf=0.93)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“and the stable temperature allows nearly isothermal heating/cooling [1].”
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 1. Introduction to Latent Heat Thermal Energy Storage
What the sources say
- Supportedcites [1] Sarbu, I., and Sebarchievici, C. (2018). A comprehensive review of thermal energy storage. Sustainability, 10. source
Section 4, “Latent-Heat or Phase-Change Storage” (page not provided), says heat is absorbed or released at almost constant temperature during phase change and describes the storage process as isothermal. This supports the claim that LHTES enables nearly isothermal heating and cooling. (LLM, conf=0.94)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“The higher thermal storage density, large array of PCMs, and nearly isothermal behavior of LHTES systems (shown in Figure 1b) make them more convenient than the other methods [2].”
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 1. Introduction to Latent Heat Thermal Energy Storage
What the sources say
- Supportedcites [2] Khan, 2016, A review of performance enhancement of PCM based latent heat storage system within the context of materials, thermal stability and compatibility, Energy Convers. Manag. source
The Introduction describes latent heat storage as a promising method because PCMs are widely available, storage density is higher, and operation is almost isothermal. Section 4 likewise calls it a better choice of heat storage on the basis of its density and nearly isothermal process. (LLM, conf=0.93)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“This means that LHTES systems can take up less volume to store the same amount of energy as SHS”
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 1. Introduction to Latent Heat Thermal Energy Storage
What the sources say
- Supportedcites [1] Sarbu, I., and Sebarchievici, C. (2018). A comprehensive review of thermal energy storage. Sustainability, 10. source
Section 4, “Latent-Heat or Phase-Change Storage,” says that latent-heat storage increases energy storage density and therefore reduces volume. Its comparison of LHS with SHS supports the claim that LHTES can use less volume for the same stored energy. (LLM, conf=0.93)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
175 more claims · 41 with their cited sources checked
Create a free account to see all 397 claims and every source verdict.
- It may state two separate claims as one. 178
- Probably not a substantial claim. 44
- The quote only partly states this claim. 13
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 3.1.8. Fatty Acids
“Melting and cooling rates increased with the concentration of NPs, due to increased thermal conductivity [60].”
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 4. Conclusions
“| et al. (2020) | (54.4 • C) | Fe 2 O 3 | Melting and solidification | Experimental | melting and |”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 3.1.4. Paraffin with Carbons
“A 2018 study tested the melting and solidification of paraffin PCM with a melting range of 58-60 • C and MWCNTs.”
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 4. Conclusions
“| Murugan et al. (2018) [43] | Paraffin (18-23 • C) Low | MWCNT | Melting and solidification | Experimental | up to 0.3 wt % MWCNT, solidification up to |”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 3.1.1. Water NePCMs with Cu
“Khodadadi and Hosseinizadeh were among the first researchers to study NePCMs, with their numerical model for water PCM enhanced with copper NPs.They studied the influence dispersion of NPs on the thermal conductivity, solidification rate, and latent heat of fusion.The latent heat of fusion was lowered, the rate of heat release was increased, and thermal conductivity was enhanced with the addition of NPs.It was concluded that NePCM was promising for thermal energy storage applications [28].”
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > References
“29. Khodadadi, J.M.; Hosseinizadeh, S.F. Nanoparticle-enhanced phase change materials (NEPCM) with great potential for improved thermal energy storage. Int. Commun. Heat Mass Transf. 2007, 34, 534-543. [CrossRef]”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 3.2. NePCM and Fins
“Copper oxide particles were chosen also by Li et al. [77], who examined the charging process of paraffin PCM with different sizes and configurations of Y-shaped fins.Six different cases of fins were studied.As is demonstrated in Figure 11, the fourth case, with long, thin fins alternating attachment to the outer and inner wall, was the best case.”
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 4. Conclusions
“Figure: 11 Figure 11 . Figure 11.The liquid fraction in the six different cases at different times.(Copyright 2020 Elsevier) [80].”
Cited works that were retracted
Works this paper cites that were later retracted, from the retraction notices publishers deposit. Major when the notice came out before this paper was published.
A note, not an issue: for example, a cited work that was retracted only after this paper was published, which its authors could not have known.
In the paper
“…and Hosseinizadeh (2007) [28] Water (0 ◦C) Low Cu Solidification Numerical The NPs enhanced the heat transfer and solidification Jourabian and Farhadi (2015) [29] Ice (0 ◦C) Low Cu Melting Numerical (2D) NPs increased the thermal conductivity Feng et al. (2015) [30] Water (0…”
Cited work 10.1007/s12206-015-0828-0 · retracted 2021-11-02 · notice 10.1007/s12206-021-0946-9 · this paper published 2021-06-25
Citations
Cites
1 retracted
Jourabian, M., & Farhadi, M. (2015) · Journal of Mechanical Science and Technology · doi:10.1007/s12206-015-0828-0 · Cited by 50 · cited 3×
“…and Hosseinizadeh (2007) [28] Water (0 ◦C) Low Cu Solidification Numerical The NPs enhanced the heat transfer and solidification Jourabian and Farhadi (2015) [29] Ice (0 ◦C) Low Cu Melting Numerical (2D) NPs increased the thermal conductivity Feng et al. (2015) [30] Water (0…”
BackgroundInfluentialRetractedReview on thermal energy storage with phase change materials and applications
Sharma, A., Tyagi, V. V., Chen, C. R., & Buddhi, D. (2009) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2007.10.005 · Cited by 5,936 · cited 7×
“Paraffins are composed of straight chain nalkanes (CH3–(CH2)–CH3); the general formula for fatty acids is CH3(CH2)2n•COOH; salt hydrates are composed of inorganic salts and water (AB•nH2O), and metallic hydrates consist of metals with low melting points relative to most metals [9].”
BackgroundInfluentialA Comprehensive Review of Thermal Energy Storage
Sarbu, I., & Sebarchievici, C. (2018) · Sustainability · doi:10.3390/su10010191 · Cited by 1,311 · cited 9×
“Temperature change is what drives SHS, as shown in Figure 1a [1].”
BackgroundInfluentialKhan, Z., Khan, Z., & Ghafoor, A. (2016) · Energy Conversion and Management · doi:10.1016/j.enconman.2016.02.045 · Cited by 765 · cited 5×
“They also have the disadvantage of low thermal conductivity, as well as toxicity, corrosivity, instability, and flammability, while also being much more expensive than paraffin [1,2].”
BackgroundMethodInfluentialKhodadadi, J. M., & Hosseinizadeh, S. F. (2007) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2007.02.005 · Cited by 715 · cited 1×
“…(2005) [27] Paraffin wax (67 ◦C) Low Carbon nanofibers Solidification Experimental andanalytical (1D) The nanofibers enhanced the PCM performance Khodadadi and Hosseinizadeh (2007) [28] Water (0 ◦C) Low Cu Solidification Numerical The NPs enhanced the heat transfer and…”
BackgroundPhase change materials and thermal energy storage for buildings
de Gracia, A., & Cabeza, L. F. (2015) · Energy and Buildings · doi:10.1016/j.enbuild.2015.06.007 · Cited by 688 · cited 1×
“(a) Sensible heat, (b) latent heat, (c) thermo-chemical thermal energy storage systems (Copyright 2015 Gracia and Cabeza) [4].”
BackgroundEffect of carbon nanofiber additives on thermal behavior of phase change materials
Elgafy, A., & Lafdi, K. (2005) · Carbon · doi:10.1016/j.carbon.2005.06.042 · Cited by 430 · cited 7×
“Authors PCM Melting Point (◦C) Nanoparticle Type Phase Change Process Study Case Result Elgafy and Lafdi (2005) [27] Paraffin wax (67 ◦C) Low Carbon nanofibers Solidification Experimental andanalytical (1D) The nanofibers enhanced the PCM performance Khodadadi and Hosseinizadeh (2007) [28] Water (0 ◦C) Low Cu Solidifi…”
BackgroundInfluentialNanoparticles enhanced phase change materials (NePCMs)-A recent review
Tariq, S. L., Ali, H. M., Akram, M. A., Janjua, M. M., & Ahmadlouydarab, M. (2020) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2020.115305 · Cited by 405 · cited 2×
“Even some medical applications exist, including smart textiles, which can work to either heat or cool the person depending on the need [6].”
BackgroundChieruzzi, M., Cerritelli, G. F., Miliozzi, A., & Kenny, J. M. (2013) · Nanoscale Research Letters · doi:10.1186/1556-276x-8-448 · Cited by 381 · cited 1×
“…◦C) Middle COOHfunctionalized Graphene nanoplatelets (f-GNP) Melting and solidification Experimental andnumerical (2D) f-GNPs enhance PCM at 5% concentration Chieruzzi et al. (2013) [66] NaNO3-KNO3 (223–232 ◦C) Middle SiO2, Al2O3, TiO2, and SiO2-Al2O3 Melting and solidification Experimental 1.0…”
BackgroundInfluentialJiang, Z. Y., & Qu, Z. G. (2019) · Applied Energy · doi:10.1016/j.apenergy.2019.03.043 · Cited by 380 · cited 2×
“Jiang and Qu [5] used a heat pipe in a PCM-based lithium-ion battery thermal management system, where it was found that the heat pipe increased the efficiency of the cooling system significantly.”
Background
Research works printed but not linked: 3
- Zaidan, 2018, Improvement in heat transfer inside a phase change energy system, Int. J. Mech. Mechatron. Eng., 18, 33
- Temel, 2018, Determination of thermal properties of a82 organic phase change material embedded with different type nanoparticles. Farkli Tipte Nanoparçaciklarla Katkilanan A82 Organik Faz Değiştiren Malzemenin Termal, Özellİklerİnİn Belirlenmesi, 38, 75
- Manickam, 2019, Erythritol based nano-PCM for solar thermal energy storage, Int. Res. J. Eng. Technol., 6, 1631
Cited by
Nano-enhanced phase change materials: Fundamentals and applications
Said, Z., Pandey, A. K., Tiwari, A. K., Kalidasan, B., Jamil, F., Thakur, A. K., Tyagi, V. V., Sarı, A., & Ali, H. M. (2024) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2024.101162 · Cited by 386
Togun, H., Sultan, H. S., Mohammed, H. I., Sadeq, A. M., Biswas, N., Hasan, H. A., Homod, R. Z., Abdulkadhim, A. H., Yaseen, Z. M., & Talebizadehsardari, P. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2023.109840 · Cited by 245
Progress and key challenges in catalytic combustion of lean methane
Feng, X., Jiang, L., Li, D., Tian, S., Zhu, X., Wang, H., He, C., & Li, K. (2022) · Journal of Energy Chemistry · doi:10.1016/j.jechem.2022.08.001 · Cited by 211
Ghosh, D., Ghose, J., Datta, P., Kumari, P., & Paul, S. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.105179 · Cited by 163
A brief review on different hybrid methods of enhancement within latent heat storage systems
Khademi, A., Shank, K. J., Mehrjardi, S. A. A., Tiari, S., Sorrentino, G., Said, Z., Chamkha, A. J., & Ushak, S. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.105362 · Cited by 122
Self-citation
Metadata
- Authors
- Tofani, K., & Tiari, S.
- Affiliations
- Gannon University (US)
- Corresponding author
- Tiari, Saeed
- ORCID
- Tiari, Saeed
- Venue
- Energies
- Publisher
- MDPI AG
- Published
- 2021-06-25
- Volume
- 14
- Issue
- 13
- Pages
- 3821
- ISSN
- 1996-1073 (ISSN-L)
- OpenAlex
- W3175481636
- Cited by
- 114
- References
- 93
- Citations by year
- 2026: 34 · 2025: 18 · 2024: 21 · 2023: 22 · 2022: 16 · 2021: 3
- FWCI
- 6.62
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Energies (publishedVersion, cc-by)
- RePEc: Research Papers in Economics (submittedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Phase Change Materials Research
- Physical Sciences › Engineering › Mechanical Engineering › Adsorption and Cooling Systems
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Solar Thermal and Photovoltaic Systems
- Keywords
- nano-enhanced phase change materials, latent heat storage, thermal conductivity enhancement, nanoparticles, metal foam, heat pipes, fins, porous media, solar energy storage, alkanes, Al2O3 nanoparticles, copper nanoparticles, carbon nanoparticles
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-09-28, under version 3 of the claim definition (prompt extract-v3).
A second model labelled each claim on 2026-09-28 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review. https://app.cochat.ai/papers/10.3390/en14133821
- The paper
- Tofani, K., & Tiari, S. (2021). Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review. Energies. https://doi.org/10.3390/en14133821
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.