Impact of Wearing on Filtration Performance of Electrostatic Filter Face Masks
Open accessThe DOI matches its Crossref record; 21 of the 21 references it cites were found in a registry or an index.
Abstract
Certified disposable respirators afford important protection from hazardous aerosols but lose performance as they are worn. This study examines the effect of wear time on filtration efficiency. Disposable respirators were worn by CSIRO staff over a period of 4 weeks in early 2020. Participants wore the respirator masks for given times up to eight hours whilst working in laboratory/office environments. At that time COVID-19 precautions required staff to wear surgical (or other) masks and increase use of hand sanitizer from dispenser stations. Results obtained from a test group of ten individuals without health preconditions show an increasing number of masks failing with wear time, while the remainder continue to perform nearly unaffected for up to 8 h. Some masks were found to retain filtration performance better than others, possibly due to the type of challenge they were subjected to by the wearer. However, the rate and extent of decay are expected to differ between environments since there are many contributing factors and properties of the aerosol challenge cannot be controlled in a live trial. Penetration and variability increased during wear; the longer the wear time, the more deleterious to particle removal, particularly after approximately 2 h of wear. This behavior is captured in a descriptive statistical model based on results from a trial with this test group. The effectiveness of the masks in preventing the penetration of KCl particles was determined before and after wearing, with the analysis focusing on the most penetrating particles in a size range of 0.3–0.5 µm diameter where respirator masks are most vulnerable. The basic elements of the study, including the approach to filter testing and sample sanitization, are broadly applicable. Conclusions also have applicability to typical commercially available single-use respirator masks manufactured from melt blown polypropylene as they are reliant on the same physical principles for particle capture and electrostatic enhancement was comparable for the particle size range used for detection.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Figures
![Figure 1 (a) An example of the particle-size dependence of penetration for charged and discharged wool/polypropylene (Wool–PP, WP) and melt blown polypropylene (Meltblown PP, MBP; Shanghai Da Sheng [5]) mask media when tested at a face velocity of 0.15 m/s. Pressure drop, thickness, fabric areal density, maximum penetration, and most penetrable particle size (MPPS) of MBP: 200 Pa, 3.0 mm, 280 g/m2, 0.5%, 48 nm; WP: 50 Pa, 8.8 mm, 600 g/m2, 2.2%, and 46 nm, respectively. The particle diameter size range used for measuring penetration P0.3 has been highlighted in green. Trendlines (B-Spline) have been added for illustration purposes to measurements represented by dots. (b) Fiber-polymer specific charge distribution in electrostatically enhanced media of the tribo-electric type. (c) Charge distribution resulting from DC corona charging using a unipolar electrode configuration (example for unipolar, positive electrode configuration [8]).](https://figures.cochat.ai/paper-figures/849d5e18b4c74dfabe4bf5de9e80272a/impact-of-wearing-on-filtration-performance-of-electrostatic-filter-face-masks-figure-1.jpg)






![Figure 8 Dust loading performances of sanitized mask media in unworn and worn state. Low and high loss refer to the observed level of deterioration that the mask media incurred during wear. Mathematical fit functions used to illustrate dust loading dependencies were described in [25].](https://figures.cochat.ai/paper-figures/a729fd83a74f4424974132c9c8b0b93b/impact-of-wearing-on-filtration-performance-of-electrostatic-filter-face-masks-figure-8.jpg)

Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“Other factors potentially affecting inhalation mask efficiency but not considered in this work include particle liquid content as a function of temperature and humidity; inhalation rate dependence on exercise, speaking [56], individual physiology, or demographics; particle charge dependence; and degradation after multiple uses [57].”
From Comparative Mask Protection against Inhaling Wildfire Smoke, Allergenic Bioaerosols, and Infectious Particles (2022) · cites this paper as [57]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Fitting Linear Mixed-Effects Models Using lme4
Bates, D., Mächler, M., Bolker, B., & Walker, S. (2015) · Journal of Statistical Software · doi:10.18637/jss.v067.i01 · Cited by 86,835 · cited 1×
“3) were fitted with the lme4 package in R [22] and compared using analysis of variance to test the effects of areal density, heat treatment and wear time.”
MethodCan N95 Respirators Be Reused after Disinfection? How Many Times?
Liao, L., Xiao, W., Zhao, M., Yu, X., Wang, H., Wang, Q., Chu, S., & Cui, Y. (2020) · ACS Nano · doi:10.1021/acsnano.0c03597 · Cited by 431
Effectiveness of N95 Respirator Decontamination and Reuse against SARS-CoV-2 Virus
Fischer, R. J., Morris, D. H., van Doremalen, N., Sarchette, S., Matson, M. J., Bushmaker, T., Yinda, C. K., Seifert, S. N., Gamble, A., Williamson, B. N., et al. (2020) · Emerging Infectious Diseases · doi:10.3201/eid2609.201524 · Cited by 310 · cited 2×
“To mitigate potential exposure to the virus, the filter discs were sanitized by a heat treatment at 70 °C for one hour [19] before testing, followed by the same treatment after wearing and then testing again.”
MethodRubio-Romero, J. C., Pardo-Ferreira, M. D. C., Torrecilla-García, J. A., & Calero-Castro, S. (2020) · Safety Science · doi:10.1016/j.ssci.2020.104830 · Cited by 281
Experimental Study of Electrostatic Capture Mechanisms in Commercial Electret Filters
Romay, F. J., Liu, B. Y. H., & Chae, S. J. (1998) · Aerosol Science and Technology · doi:10.1080/02786829808965523 · Cited by 147 · cited 1×
“Whilst the two filter materials have different compositions and structures, they both rely on the principle of small particle capture through electrostatic charge [16], and so the results from wool/polypropylene are also applicable for charged, melt blown filter materials [6,17,18].”
BackgroundGrinshpun, S. A., Yermakov, M. V., & Khodoun, M. V. (2020) · Journal of Hospital Infection · doi:10.1016/j.jhin.2020.06.030 · Cited by 91
Parameters Affecting the Loading Behavior and Degradation of Electrically Active Filter Materials
Walsh, D. C., & Stenhouse, J. I. T. (1998) · Aerosol Science and Technology · doi:10.1080/02786829808965580 · Cited by 81 · cited 2×
“bution of particle sizes [17], humidity and temperature [24,30], the type of electrostatic enhancement [6], active area, and design of the respirator mask [31], as well as environmental factors like the presence of ambient contaminants (e.”
BackgroundThe collection performance of electret filters in the particle size range 10 nm-10 μm
Baumgartner, H., & Löffler, F. (1986) · Journal of Aerosol Science · doi:10.1016/0021-8502(86)90126-6 · Cited by 79 · cited 2×
“bution of particle sizes [17], humidity and temperature [24,30], the type of electrostatic enhancement [6], active area, and design of the respirator mask [31], as well as environmental factors like the presence of ambient contaminants (e.”
BackgroundLiu, C., Dai, Z., He, B., & Ke, Q. (2020) · Materials · doi:10.3390/ma13214774 · Cited by 75 · cited 1×
“bution of particle sizes [17], humidity and temperature [24,30], the type of electrostatic enhancement [6], active area, and design of the respirator mask [31], as well as environmental factors like the presence of ambient contaminants (e.”
BackgroundLin, Y.-C., & Chen, C. (2017) · PLoS ONE · doi:10.1371/journal.pone.0188638 · Cited by 60 · cited 1×
“bution of particle sizes [17], humidity and temperature [24,30], the type of electrostatic enhancement [6], active area, and design of the respirator mask [31], as well as environmental factors like the presence of ambient contaminants (e.”
BackgroundElectrostatic interactions between the SARS-CoV-2 virus and a charged electret fibre
Javidpour, L., Božič, A., Naji, A., & Podgornik, R. (2021) · Soft Matter · doi:10.1039/d1sm00232e · Cited by 51
Reliability of electret filters
Lehtimäki, M., & Heinonen, K. (1994) · Building and Environment · doi:10.1016/0360-1323(94)90033-7 · Cited by 46 · cited 1×
“Whilst the two filter materials have different compositions and structures, they both rely on the principle of small particle capture through electrostatic charge [16], and so the results from wool/polypropylene are also applicable for charged, melt blown filter materials [6,17,18].”
BackgroundPerić, R., & Perić, M. (2020) · Journal of Applied Fluid Mechanics · doi:10.47176/jafm.13.06.31812 · Cited by 41 · cited 3×
“Given the significantly different pressure drop associated with the wool/polypropylene filter media (30 Pa) compared to typical, commercially available melt blown polypropylene respirators (typically approximately 200 Pa for a N95 respirator), the analytical model [21] was used to predict differences in potential leak…”
MethodInfluentialEffect of electric charge in filter materials
Brown, R. (1989) · Filtration & Separation · doi:10.1016/s0015-1882(89)80057-6 · Cited by 26
A Study of Wool/Polypropylene Non-wovens as an Alternative to the Hansen Filter
Schütz, J. A., & Humphries, W. (2010) · Textile Research Journal · doi:10.1177/0040517509358803 · Cited by 22 · cited 2×
“This filter medium was chosen for the wear trials as it would easily seal against the wearer’s face due to long-distance electrostatic charge and its penetration was highly stable over time [20].”
BackgroundSelf-citationEffectiveness of N95 Facepiece Respirators in Filtering Aerosol Following Storage and Sterilization
Lin, T.-H., Tseng, C., Huang, Y.-L., Lin, H.-C., Lai, C.-Y., & Lee, S.-A. (2020) · Aerosol and Air Quality Research · doi:10.4209/aaqr.2019.12.0620 · Cited by 20
Determination of the optimal time for N95 respirator for aerosol infection control
Du, J., Zhang, L., Liu, Y., Shu, W., Ma, Y., Gao, J., & Li, L. (2020) · Medicine · doi:10.1097/md.0000000000023709 · Cited by 17 · cited 1×
“3 penetrations are typically four times higher than penetrations obtained from total mass measurement, a technique used in the study of worn N95 masks [13], and more sensitive to filtration performance deterioration.”
MethodRespiratory protection for physiologically straining environments
Schütz, J. A., & Church, J. S. (2011) · Textile Research Journal · doi:10.1177/0040517511402127 · Cited by 15 · cited 2×
“Filter media with an electrostatic charge may also be produced from two types of fibers of different material compositions using tribo-electric charging [6], for example, wool and polypropylene [7].”
BackgroundMethodSelf-citationDuncan, S., Bodurtha, P., Bourgeois, C., Dickson, E., Jensen, C., & Naqvi, S. (2020) · Journal of Occupational and Environmental Hygiene · doi:10.1080/15459624.2020.1829633 · Cited by 14 · cited 3×
“Another study investigated the effects of wear in terms of total inward leakage (TIL) that takes the effects of facial seal into account [14].”
BackgroundInfluentialCarsí, M., & Alonso, M. (2021) · Journal of Aerosol Science · doi:10.1016/j.jaerosci.2021.105849 · Cited by 12 · cited 1×
“There are many parameters and conditions that can influence results, such as the charge that aerosol particles carry [26,27], their physical state (solid or liquid) [28,29] and the distri-”
BackgroundThe Effect of Sanitizing Treatments on Respirator Filtration Performance
Schütz, J. A., Pierlot, A. P., & Alexander, D. L. (2022) · International Journal of Environmental Research and Public Health · doi:10.3390/ijerph19020641 · Cited by 4 · cited 4×
“The central 113 mm diameter of the sample (equivalent to 100 cm2 active area) was exposed to the challenge aerosol when located in the sample holder of the instrument [5].”
BackgroundMethodSelf-citation
Research works printed but not linked: 2
- Schütz J.A. Maxwell J.M. Huson M.G. 3.7 Hunt for Charges in Electret Filters with a Scanning Probe Microscope. In Proceedings of the TANDEC 11th Annual International Nonwovens Conference, The University of Tennessee Knoxville, TN, USA 6–8 November 2001
- Schütz J.A. Interdependence of Fine Particle Filtration Performance and Dust Load for Electrostatic Media Filtration 2008 8 252 258
Cited by
Wagner, J., Macher, J. M., Chen, W., & Kumagai, K. (2022) · International Journal of Environmental Research and Public Health · doi:10.3390/ijerph192315555 · Cited by 14
“Other factors potentially affecting inhalation mask efficiency but not considered in this work include particle liquid content as a function of temperature and humidity; inhalation rate dependence on exercise, speaking [56], individual physiology, or demographics; particle charge dependence; and degradation after mult…”
BackgroundDevelopment of a desktop mask charger
Ikawa, T., Fujita, K., Kiuchi, S., Li, M., Kushima, A., Takase, H., Das, B., Morita, M., Todo, H., Pennington, M., et al. (2023) · Heliyon · doi:10.1016/j.heliyon.2023.e15359 · Cited by 1
Droplets Adhesion to Surgical Masks during Standard Oral Surgery
Yoshida, H., Makino, A., Yamaguchi, A., Matsuda, S., Sakamaki, I., Yoshimura, H., & Iwasaki, H. (2022) · Japanese Journal of Infectious Diseases · doi:10.7883/yoken.jjid.2022.184
Unveiling the Barrier: A Simulation Study on Face Mask Filtration
Panawala, P. S. S., Mudalige, S. P., Amarasinghe, D. A. S., Attygalle, D., Samarasekara, A. M. P. B., & Weragoda, V. S. C. (2023) · Moratuwa Engineering Research Conference (MERCon) · doi:10.1109/mercon60487.2023.10355408
“By employing the electrostatic filtration mechanism, fibrous face masks can significantly enhance their ability to capture such particles, providing a higher level of filtration efficiency [14].”
BackgroundFaridi, S., Yousefian, F., Niazi, S., Ghalhari, M. R., Rafiee, A., Harrison, R. M., Brook, R. D., Contini, D., Kumar, P., Naddafi, K., et al. (2024) · Atmosphere · doi:10.3390/atmos15121447
Metadata
- Authors
- Pierlot, A. P., Alexander, D. L. J., & Schütz, J. A.
- Affiliations
- Commonwealth Scientific and Industrial Research Organisation (AU)
- Corresponding author
- Alexander, David L. J.
- Venue
- International Journal of Environmental Research and Public Health
- Publisher
- MDPI AG
- Published
- 2022-04-21
- Volume
- 19
- Issue
- 9
- Pages
- 5032
- ISSN
- 1660-4601 (ISSN-L)
- PMC
- PMC9100139
- OpenAlex
- W4224301378
- Cited by
- 7
- References
- 21
- Citations by year
- 2026: 2 · 2024: 1 · 2023: 2 · 2022: 2
- FWCI
- 0.34
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- International Journal of Environmental Research and Public Health (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- RePEc: Research Papers in Economics (submittedVersion)
- Funders
- Australian Government
- Commonwealth Scientific and Industrial Research Organisation
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Aerosol Filtration and Electrostatic Precipitation
- Health Sciences › Medicine › Pulmonary and Respiratory Medicine › Infection Control and Ventilation
- Health Sciences › Medicine › Public Health, Environmental and Occupational Health › Occupational Health and Safety in Workplaces
- Keywords
- filtration efficiency, electrostatic filtration, particle penetration, aerosol challenge, COVID-19 pandemic, hand sanitizer, particle size distribution
- MeSH terms
- COVID-19, Aerosols, Filtration, Humans, Masks, Particle Size, Respiratory Protective Devices, Static Electricity
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.