The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
Polylactide (PLA) Filaments a Biobased Solution for Additive Manufacturing: Correlating Rheology and Thermomechanical Properties with Printing Quality
Open accessAbstract
Three commercial filaments for Fused Deposition Modeling (FDM) were selected to study the influence of polymer formulation on the printing quality and mechanical properties of FDM specimens. The three filaments were all based on polylactic acid (PLA) as the matrix, and they are sold as PLA filaments. The printing quality was tested by printing one complex shape with overhang features. The marked shear thinning behavior for two filaments was observed by rheology. The filaments were also studied by scanning electron microscopy and thermogravimetric analysis (TGA) to unveil their composition. The filaments with the best printing quality showed the presence of mineral fillers, which explained the melt behavior observed by rheology. The tensile testing confirmed that the filled PLA was the best-performing filament both in terms of printing quality and thermomechanical performance, with a p-value = 0.106 for the tensile modulus, and a p-value = 0.615 for the ultimate tensile strength.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Correlation of dynamic and steady flow viscosities
Cox, W. P., & Merz, E. H. (1958) · Journal of Polymer Science · doi:10.1002/pol.1958.1202811812 · Cited by 2,092
Cited by
Nicolas, J., Magli, S., Rabbachin, L., Sampaolesi, S., Nicotra, F., & Russo, L. (2020) · Biomacromolecules · doi:10.1021/acs.biomac.0c00045 · Cited by 509
Additive Manufacturing of Polymer Materials: Progress, Promise and Challenges
Saleh Alghamdi, S., John, S., Roy Choudhury, N., & Dutta, N. K. (2021) · Polymers · doi:10.3390/polym13050753 · Cited by 469
Bioplastic production in terms of life cycle assessment: A state-of-the-art review
Ali, S. S., Abdelkarim, E. A., Elsamahy, T., Al-Tohamy, R., Li, F., Kornaros, M., Zuorro, A., Zhu, D., & Sun, J. (2023) · Environmental Science and Ecotechnology · doi:10.1016/j.ese.2023.100254 · Cited by 361
Azad, M. A., Olawuni, D., Kimbell, G., Badruddoza, A. Z. M., Hossain, M. S., & Sultana, T. (2020) · Pharmaceutics · doi:10.3390/pharmaceutics12020124 · Cited by 356
Bhandari, S., Lopez-Anido, R. A., & Gardner, D. J. (2019) · Additive Manufacturing · doi:10.1016/j.addma.2019.100922 · Cited by 355
Metadata
- Authors
- Cicala, G., Giordano, D., Tosto, C., Filippone, G., Recca, A., & Blanco, I.
- Venue
- Materials
- Publisher
- MDPI AG
- Published
- 2018-07-11
- Volume
- 11
- Issue
- 7
- Pages
- 1191
- ISSN
- 1996-1944 (ISSN-L)
- OpenAlex
- W2815531929
- Cited by
- 166
- References
- 1
- FWCI
- 11.43
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Polylactide (PLA) Filaments a Biobased Solution for Additive Manufacturing: Correlating Rheology and Thermomechanical Properties with Printing Quality. https://app.cochat.ai/papers/10.3390/ma11071191
- The paper
- Cicala, G., Giordano, D., Tosto, C., Filippone, G., Recca, A., & Blanco, I. (2018). Polylactide (PLA) Filaments a Biobased Solution for Additive Manufacturing: Correlating Rheology and Thermomechanical Properties with Printing Quality. Materials. https://doi.org/10.3390/ma11071191
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.