The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
Fused Particle Fabrication 3-D Printing: Recycled Materials’ Optimization and Mechanical Properties
Open accessAbstract
Fused particle fabrication (FPF) (or fused granular fabrication (FGF)) has potential for increasing recycled polymers in 3-D printing. Here, the open source Gigabot X is used to develop a new method to optimize FPF/FGF for recycled materials. Virgin polylactic acid (PLA) pellets and prints were analyzed and were then compared to four recycled polymers including the two most popular printing materials (PLA and acrylonitrile butadiene styrene (ABS)) as well as the two most common waste plastics (polyethylene terephthalate (PET) and polypropylene (PP)). The size characteristics of the various materials were quantified using digital image processing. Then, power and nozzle velocity matrices were used to optimize the print speed, and a print test was used to maximize the output for a two-temperature stage extruder for a given polymer feedstock. ASTM type 4 tensile tests were used to determine the mechanical properties of each plastic when they were printed with a particle drive extruder system and were compared with filament printing. The results showed that the Gigabot X can print materials 6.5× to 13× faster than conventional printers depending on the material, with no significant reduction in the mechanical properties. It was concluded that the Gigabot X and similar FPF/FGF printers can utilize a wide range of recycled polymer materials with minimal post processing.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Plastics Recycling: Challenges and Opportunities
Hopewell, J., Dvorak, R., & Kosior, E. (2009) · Philosophical Transactions of the Royal Society B: Biological Sciences · doi:10.1098/rstb.2008.0311 · Cited by 3,201
Cited by
Assessing relations between Circular Economy and Industry 4.0: a systematic literature review
Rosa, P., Sassanelli, C., Urbinati, A., Chiaroni, D., & Terzi, S. (2020) · International Journal of Production Research · doi:10.1080/00207543.2019.1680896 · Cited by 733
Cruz Sanchez, F. A., Boudaoud, H., Camargo, M., & Pearce, J. M. (2020) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.121602 · Cited by 410
Self-citation3D printing filament as a second life of waste plastics—a review
Mikula, K., Skrzypczak, D., Izydorczyk, G., Warchoł, J., Moustakas, K., Chojnacka, K., & Witek-Krowiak, A. (2021) · Environmental Science and Pollution Research · doi:10.1007/s11356-020-10657-8 · Cited by 382
Bhagia, S., Bornani, K., Agrawal, R., Satlewal, A., Ďurkovič, J., Lagaňa, R., Bhagia, M., Yoo, C. G., Zhao, X., Kunc, V., et al. (2021) · Applied Materials Today · doi:10.1016/j.apmt.2021.101078 · Cited by 337
Colorado, H. A., Velásquez, E. I. G., & Monteiro, S. N. (2020) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2020.04.062 · Cited by 320
Metadata
- Authors
- Woern, A. L., Byard, D. J., Oakley, R. B., Fiedler, M. J., Snabes, S. L., & Pearce, J. M.
- Venue
- Materials
- Publisher
- MDPI AG
- Published
- 2018-08-12
- Volume
- 11
- Issue
- 8
- Pages
- 1413
- ISSN
- 1996-1944 (ISSN-L)
- OpenAlex
- W2885803342
- Cited by
- 233
- References
- 1
- FWCI
- 8.93
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Fused Particle Fabrication 3-D Printing: Recycled Materials’ Optimization and Mechanical Properties. https://app.cochat.ai/papers/10.3390/ma11081413
- The paper
- Woern, A. L., Byard, D. J., Oakley, R. B., Fiedler, M. J., Snabes, S. L., & Pearce, J. M. (2018). Fused Particle Fabrication 3-D Printing: Recycled Materials’ Optimization and Mechanical Properties. Materials. https://doi.org/10.3390/ma11081413
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.