Experimental Study of Drilling Temperature, Geometrical Errors and Thermal Expansion of Drill on Hole Accuracy When Drilling CFRP/Ti Alloy Stacks
Open accessThe DOI matches its Crossref record; 55 of the 57 references it cites were found in a registry or an index.
Abstract
The drilling of holes in CFRP/Ti (Carbon Fiber-Reinforced Plastic/Titanium alloy) alloy stacks is one of the frequently used mechanical operations during the manufacturing of fastening assemblies in temporary civil aircraft. A combination of inhomogeneous behavior and poor machinability of CFRP/Ti alloy stacks in one short drilling brought challenges to the manufacturing community. The impact of the drilling temperature and time delay factor under various cutting conditions on hole accuracy when machining CFRP/Ti alloy stacks is poorly studied. In this paper, the drilling temperature, the phenomenon of thermal expansion of the drill tool, and hole accuracy are investigated. An experimental study was carried out using thermocouples, the coordinate measuring machine method, and finite element analysis. The results showed that the time delay factor varied from 5 (s) to 120 (s), influences the thermal-dependent properties of CFRP, and leads to an increase in hole roundness. Additionally, the thermal expansion of the drill significantly contributes to the deviation of the hole diameter in Ti alloy.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Figures








Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The cited source doesn’t support the claim as written.
In the citing paper
“Because the effect of various cutting conditions on hole damage, dimensional hole accuracy, and hole quality when machining CFRP/Ti alloy stacks has been little studied [7-11].”
From Evaluation and multi-criteria optimization of surface roughness, deviation from dimensional accuracy and roundness error in drilling CFRP/Ti6Al4 stacks (2022) · cites this paper as [7]
Checked by a reasoning model — may be wrong.
Experimental — accuracy not yet measuredThe source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“Again, a lower deviation from dimensional accuracy values was obtained for both CFRP, and Ti6Al4V components at low feed rate drilling of CFRP/Ti6Al4V mixed metallic stack [7, 8, 10, 17, 18, 20, 21, 24, 42].”
From Evaluation and multi-criteria optimization of surface roughness, deviation from dimensional accuracy and roundness error in drilling CFRP/Ti6Al4 stacks (2022) · cites this paper as [7]
Experimental — accuracy not yet measuredThe source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“In the drilling of CFRP, the roundness error values of the holes Re were 810.47% larger on average than the Ti6Al4V alloy [6-9, 17, 19, 20, 23, 38].”
From Evaluation and multi-criteria optimization of surface roughness, deviation from dimensional accuracy and roundness error in drilling CFRP/Ti6Al4 stacks (2022) · cites this paper as [7]
Experimental — accuracy not yet measuredThe check wasn’t confident either way, so it gives no verdict — never disputed.
In the citing paper
“Lower roundness error values were obtained at the lowest cutting speed when drilling through the metallic stack in one go [7, 8, 10, 17, 18, 20, 21, 24, 42].”
From Evaluation and multi-criteria optimization of surface roughness, deviation from dimensional accuracy and roundness error in drilling CFRP/Ti6Al4 stacks (2022) · cites this paper as [7]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Chen, W.-C. (1997) · International Journal of Machine Tools and Manufacture · doi:10.1016/s0890-6955(96)00095-8 · Cited by 752
DAVIM, J., RUBIO, J., & ABRAO, A. (2007) · Composites Science and Technology · doi:10.1016/j.compscitech.2006.10.009 · Cited by 551
Tungsten Carbides: Structure, Properties and Application in Hardmetals
Kurlov, A. S., & Gusev, A. I. (2013) · Springer series in materials science · doi:10.1007/978-3-319-00524-9 · Cited by 279
Recent advances in drilling hybrid FRP/Ti composite: A state-of-the-art review
Xu, J., Mkaddem, A., & El Mansori, M. (2016) · Composite Structures · doi:10.1016/j.compstruct.2015.09.028 · Cited by 242
Temperature measurement of cutting tool and machined surface layer in milling of CFRP
Yashiro, T., Ogawa, T., & Sasahara, H. (2013) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2013.03.009 · Cited by 212
Experimental study on drilling mechanisms and strategies of hybrid CFRP/Ti stacks
Xu, J., & El Mansori, M. (2016) · Composite Structures · doi:10.1016/j.compstruct.2016.07.025 · Cited by 162
Drilling temperature and hole quality in drilling of CFRP/aluminum stacks using diamond coated drill
Wang, C.-Y., Chen, Y.-H., An, Q.-L., Cai, X.-J., Ming, W.-W., & Chen, M. (2015) · International Journal of Precision Engineering and Manufacturing · doi:10.1007/s12541-015-0222-y · Cited by 158
Zitoune, R., Krishnaraj, V., Collombet, F., & Roux, S. L. (2016) · Composite Structures · doi:10.1016/j.compstruct.2016.02.084 · Cited by 126
Isbilir, O., & Ghassemieh, E. (2013) · Machining Science and Technology · doi:10.1080/10910344.2013.806098 · Cited by 107 · cited 1×
“Hole quality in CFRP/Ti alloy stack is characterized by the following respond values in Ti: Surface roughness [1], hole diameter, geometrical accuracy (roundness) [2], burr size [3]; and in CFRP by delamination factor (Fd) [4,5], thermal destruction, and the damage value (Qd) [6].”
BackgroundInfluentialMerino-Pérez, J. L., Royer, R., Ayvar-Soberanis, S., Merson, E., & Hodzic, A. (2014) · Composite Structures · doi:10.1016/j.compstruct.2014.12.033 · Cited by 104
Research works printed but not linked: 5
- Hassan M.H. Mahmud A.S. Abdulah J. Effects of Twist Drill Geometry and Drilling Parameters on CFRP-Aluminum Stack Up in Single Shot Drilling SciFed Mater. Res. Lett. 2018 2 1 14
- Kumar D. Gururaja S. Experimental Investigation of CFRP/Ti Stack Drilling Under Cryogenic Condition Proceedings of the International Conference on Composite Materials and Structures ICCMS Hyterabad, India 27–29 December 2017
- Kuo C.-L. Aspinwall D. Thomas W. Carr C. Pearson D. M’Saoubi R. Leahy W. Performance of multi-margin coated tools in oneshot shot drilling of metallic-composite stack materials under varying feed rate and pecking conditions Proceedings of the 38th International Matador Conference Yunlin, Taiwan 28–30 March 2015 231 238
- Prasanth R. Senthilkumar M. Prabu K. Krishnaraj V. Identification of Drill Position in CFRP/Titanium alloy Stacks using Acoustic Emission Signals Proceedings of the International Conference on Advances in Materials, Manufacturing and Applications Tamil Nadu, India 9–11 April 2015 1174 1181
- Fox-Rabinovich G. Totten E.G. Self-Organization During Friction Advanved Surface-Engineered Materials and Systems Design CRC Press Boca Raton, FL, USA 2019 459 9780367390365
Cited by
Optimization of CFRP drilling process: a review
Zhu, W., Fu, H., Li, F., Xu, J., Li, Y., & Bai, F. (2022) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-022-10112-7 · Cited by 77
A critical review addressing conventional twist drilling mechanisms and quality of CFRP/Ti stacks
Xu, J., Kolesnyk, V., Li, C., Lysenko, B., Peterka, J., & Gupta, M. K. (2023) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2023.04.226 · Cited by 51
Self-citationKolesnyk, V., Peterka, J., Alekseev, O., Нешта, А., Xu, J., Lysenko, B., Sahul, M., Martinovič, J., & Hrbál, J. (2022) · Materials · doi:10.3390/ma15051940 · Cited by 51
Self-citationKuruc, M., Vopát, T., Peterka, J., Necpál, M., Šimna, V., Milde, J., & Jurina, F. (2022) · Materials · doi:10.3390/ma15020585 · Cited by 38
Self-citationDrilling study on CFRP/Ti-6Al-4V stacks using chip breaker grooved drill
Samsudeensadham, S., & Krishnaraj, V. (2022) · Materials and Manufacturing Processes · doi:10.1080/10426914.2022.2030872 · Cited by 31
Metadata
- Authors
- Kolesnyk, V., Peterka, J., Kuruc, M., Šimna, V., Moravčíková, J., Vopát, T., & Lisovenko, D.
- Affiliations
- Sumy State University (UA)
- Slovak University of Technology in Bratislava (SK)
- Corresponding author
- Peterka, Jozef
- ORCID
- Venue
- Materials
- Publisher
- MDPI AG
- Published
- 2020-07-20
- Volume
- 13
- Issue
- 14
- Pages
- 3232
- ISSN
- 1996-1944 (ISSN-L)
- PMC
- PMC7411704
- OpenAlex
- W3042660210
- Cited by
- 44
- References
- 57
- Citations by year
- 2026: 10 · 2025: 4 · 2024: 2 · 2023: 5 · 2022: 10 · 2021: 11 · 2020: 2
- FWCI
- 3.44
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Materials (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- Electronic Sumy State University Institutional Repository (Sumy State University) (submittedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
- Funders
- Vedecká Grantová Agentúra MŠVVaŠ SR a SAV (1/0019/20)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Engineering Technology and Methodologies
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Advanced Machining and Optimization Techniques
- Keywords
- drilling, drilling temperature, hole accuracy, hole roundness, carbon fiber reinforced polymer, titanium alloys, machinability, finite element analysis, coordinate measuring machine
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Experimental Study of Drilling Temperature, Geometrical Errors and Thermal Expansion of Drill on Hole Accuracy When Drilling CFRP/Ti Alloy Stacks. https://app.cochat.ai/papers/10.3390/ma13143232
- The paper
- Kolesnyk, V., Peterka, J., Kuruc, M., Šimna, V., Moravčíková, J., Vopát, T., & Lisovenko, D. (2020). Experimental Study of Drilling Temperature, Geometrical Errors and Thermal Expansion of Drill on Hole Accuracy When Drilling CFRP/Ti Alloy Stacks. Materials. https://doi.org/10.3390/ma13143232
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.