Experimental Study of Drilling Temperature, Geometrical Errors and Thermal Expansion of Drill on Hole Accuracy When Drilling CFRP/Ti Alloy Stacks
Open accessThe DOI matches its Crossref record; 55 of the 57 references it cites were found in a registry or an index.
Abstract
The drilling of holes in CFRP/Ti (Carbon Fiber-Reinforced Plastic/Titanium alloy) alloy stacks is one of the frequently used mechanical operations during the manufacturing of fastening assemblies in temporary civil aircraft. A combination of inhomogeneous behavior and poor machinability of CFRP/Ti alloy stacks in one short drilling brought challenges to the manufacturing community. The impact of the drilling temperature and time delay factor under various cutting conditions on hole accuracy when machining CFRP/Ti alloy stacks is poorly studied. In this paper, the drilling temperature, the phenomenon of thermal expansion of the drill tool, and hole accuracy are investigated. An experimental study was carried out using thermocouples, the coordinate measuring machine method, and finite element analysis. The results showed that the time delay factor varied from 5 (s) to 120 (s), influences the thermal-dependent properties of CFRP, and leads to an increase in hole roundness. Additionally, the thermal expansion of the drill significantly contributes to the deviation of the hole diameter in Ti alloy.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Figures








Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The cited source doesn’t support the claim as written.
In the citing paper
“Because the effect of various cutting conditions on hole damage, dimensional hole accuracy, and hole quality when machining CFRP/Ti alloy stacks has been little studied [7-11].”
From Evaluation and multi-criteria optimization of surface roughness, deviation from dimensional accuracy and roundness error in drilling CFRP/Ti6Al4 stacks (2022) · cites this paper as [7]
Checked by a reasoning model — may be wrong.
Experimental — accuracy not yet measuredThe source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“Again, a lower deviation from dimensional accuracy values was obtained for both CFRP, and Ti6Al4V components at low feed rate drilling of CFRP/Ti6Al4V mixed metallic stack [7, 8, 10, 17, 18, 20, 21, 24, 42].”
From Evaluation and multi-criteria optimization of surface roughness, deviation from dimensional accuracy and roundness error in drilling CFRP/Ti6Al4 stacks (2022) · cites this paper as [7]
Experimental — accuracy not yet measuredThe source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“In the drilling of CFRP, the roundness error values of the holes Re were 810.47% larger on average than the Ti6Al4V alloy [6-9, 17, 19, 20, 23, 38].”
From Evaluation and multi-criteria optimization of surface roughness, deviation from dimensional accuracy and roundness error in drilling CFRP/Ti6Al4 stacks (2022) · cites this paper as [7]
Experimental — accuracy not yet measuredThe check wasn’t confident either way, so it gives no verdict — never disputed.
In the citing paper
“Lower roundness error values were obtained at the lowest cutting speed when drilling through the metallic stack in one go [7, 8, 10, 17, 18, 20, 21, 24, 42].”
From Evaluation and multi-criteria optimization of surface roughness, deviation from dimensional accuracy and roundness error in drilling CFRP/Ti6Al4 stacks (2022) · cites this paper as [7]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Chen, W.-C. (1997) · International Journal of Machine Tools and Manufacture · doi:10.1016/s0890-6955(96)00095-8 · Cited by 752
DAVIM, J., RUBIO, J., & ABRAO, A. (2007) · Composites Science and Technology · doi:10.1016/j.compscitech.2006.10.009 · Cited by 551
Tungsten Carbides: Structure, Properties and Application in Hardmetals
Kurlov, A. S., & Gusev, A. I. (2013) · Springer series in materials science · doi:10.1007/978-3-319-00524-9 · Cited by 279
Recent advances in drilling hybrid FRP/Ti composite: A state-of-the-art review
Xu, J., Mkaddem, A., & El Mansori, M. (2016) · Composite Structures · doi:10.1016/j.compstruct.2015.09.028 · Cited by 242
Temperature measurement of cutting tool and machined surface layer in milling of CFRP
Yashiro, T., Ogawa, T., & Sasahara, H. (2013) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2013.03.009 · Cited by 212
Experimental study on drilling mechanisms and strategies of hybrid CFRP/Ti stacks
Xu, J., & El Mansori, M. (2016) · Composite Structures · doi:10.1016/j.compstruct.2016.07.025 · Cited by 162
Drilling temperature and hole quality in drilling of CFRP/aluminum stacks using diamond coated drill
Wang, C.-Y., Chen, Y.-H., An, Q.-L., Cai, X.-J., Ming, W.-W., & Chen, M. (2015) · International Journal of Precision Engineering and Manufacturing · doi:10.1007/s12541-015-0222-y · Cited by 158
Zitoune, R., Krishnaraj, V., Collombet, F., & Roux, S. L. (2016) · Composite Structures · doi:10.1016/j.compstruct.2016.02.084 · Cited by 126
Isbilir, O., & Ghassemieh, E. (2013) · Machining Science and Technology · doi:10.1080/10910344.2013.806098 · Cited by 107 · cited 1×
“Hole quality in CFRP/Ti alloy stack is characterized by the following respond values in Ti: Surface roughness [1], hole diameter, geometrical accuracy (roundness) [2], burr size [3]; and in CFRP by delamination factor (Fd) [4,5], thermal destruction, and the damage value (Qd) [6].”
BackgroundInfluentialMerino-Pérez, J. L., Royer, R., Ayvar-Soberanis, S., Merson, E., & Hodzic, A. (2014) · Composite Structures · doi:10.1016/j.compstruct.2014.12.033 · Cited by 104
Drilling of Titanium/CFRP/Aluminium Stacks
Shyha, I., Soo, S. L., Aspinwall, D. K., Bradley, S., Dawson, S., & Pretorius, C. J. (2010) · Key engineering materials · doi:10.4028/www.scientific.net/kem.447-448.624 · Cited by 100
Voß, R., Henerichs, M., & Kuster, F. (2016) · CIRP Annals · doi:10.1016/j.cirp.2016.04.001 · Cited by 97
Burr Formation and Hole Quality when Drilling Titanium and Aluminium Alloys
Abdelhafeez, A. M., Soo, S. L., Aspinwall, D. K., Dowson, A., & Arnold, D. (2015) · Procedia CIRP · doi:10.1016/j.procir.2015.08.019 · Cited by 95
Impact of Cryogenic Condition and Drill Diameter on Drilling Performance of CFRP
BASMACI, G., YÖRÜK, A. S., Köklü, U., & Morkavuk, S. (2017) · Applied Sciences · doi:10.3390/app7070667 · Cited by 93
Voß, R., Henerichs, M., Rupp, S., Kuster, F., & Wegener, K. (2015) · CIRP journal of manufacturing science and technology · doi:10.1016/j.cirpj.2015.09.003 · Cited by 90
Wang, H., Zhang, X., & Duan, Y. (2018) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-018-1810-7 · Cited by 75
Rizal, M., GHANI, J. A., Nuawi, M. Z., & Haron, C. H. C. (2017) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-017-1251-8 · Cited by 72
Ghafarizadeh, S., Lebrun, G., & Châtelain, J.-F. (2015) · Journal of Composite Materials · doi:10.1177/0021998315587131 · Cited by 71
Study on the Drilling of Titanium/Graphite Hybrid Composites
Kim, D., & Ramulu, M. (2007) · Journal of Engineering Materials and Technology · doi:10.1115/1.2744397 · Cited by 70
Low-frequency vibration-assisted drilling of hybrid CFRP/Ti6Al4V stacked material
Hussein, R., Sadek, A., Elbestawi, M. A., & Attia, H. (2018) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-018-2410-2 · Cited by 69
Wei, Y., An, Q., Ming, W., & Chen, M. (2016) · Advances in Mechanical Engineering · doi:10.1177/1687814016670281 · Cited by 67
Miguélez, M. H., Zaera, R., Molinari, A., Cheriguene, R., & Rusinek, A. (2009) · Journal of Thermal Stresses · doi:10.1080/01495730802637134 · Cited by 64
Image Analysis for CFRP Drilled Hole Quality Assessment
Caggiano, A., Angelone, R., & Teti, R. (2017) · Procedia CIRP · doi:10.1016/j.procir.2017.03.045 · Cited by 56
A Study on Drilling High-Strength CFRP Laminates: Frictional Heat and Cutting Temperature
Xu, J., Li, C., Dang, J., Mansori, M. E., & Ren, F. Y. (2018) · Materials · doi:10.3390/ma11122366 · Cited by 56
The glass transition temperatures of highly crosslinked networks: Cured epoxy resins
Banks, L., & Ellis, B. (1982) · Polymer · doi:10.1016/0032-3861(82)90246-4 · Cited by 54
Hole diameter variation and roundness in dry orbital drilling of CFRP/Ti stacks
Lan, Z., Ke, Y., Dong, H., Chen, Z., & Gao, K. (2016) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-016-8528-1 · Cited by 54
Giasin, K., & Ayvar-Soberanis, S. (2016) · Materials · doi:10.3390/ma9080622 · Cited by 54
Microstructural investigation of drilling induced damage in fibre metal laminates constituents
Giasin, K., & Ayvar-Soberanis, S. (2017) · Composites Part A Applied Science and Manufacturing · doi:10.1016/j.compositesa.2017.02.024 · Cited by 54
Self-Organization during Friction in Complex Surface Engineered Tribosystems
Fox‐Rabinovich, G., Gershman, I. S., Yamamoto, K., Biksa, A., Veldhuis, S. C., Beake, B. D., & Kovalev, A. I. (2010) · Entropy · doi:10.3390/e12020275 · Cited by 52
Machining of CFRP/Ti6Al4V stacks under minimal quantity lubricating condition
Senthilkumar, M., Prabukarthi, A., & Krishnaraj, V. (2018) · Journal of Mechanical Science and Technology · doi:10.1007/s12206-018-0731-6 · Cited by 51
Bussu, G., & Lazzeri, A. (2006) · Journal of Materials Science · doi:10.1007/s10853-006-0694-3 · Cited by 50
Modeling of Boring Mandrel Working Process with Vibration Damper
Sentyakov, K., Peterka, J., Smirnov, V. A., Božek, P., & Sviatskii, V. (2020) · Materials · doi:10.3390/ma13081931 · Cited by 42
Self-citationUltrasonically assisted drilling of aerospace CFRP/Ti stacks
Onawumi, P., Roy, A., Silberschmidt, V. V., & Merson, E. (2018) · Procedia CIRP · doi:10.1016/j.procir.2018.09.041 · Cited by 40
Thermal aspects in machining CFRPs: effect of cutter type and cutting parameters
Sheikh-Ahmad, J. Y., Almaskari, F., & Hafeez, F. (2018) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-018-2881-1 · Cited by 40
Jurko, J., Džupon, M., Panda, A., & Zajac, J. (2012) · Advanced materials research · doi:10.4028/www.scientific.net/amr.538-541.1312 · Cited by 32
Acoustic emission for controlling drill position in fiber-reinforced plastic and metal stacks
Wertheim, R., Ben‐Hanan, U., Ihlenfeldt, S., Stoll, A., Treppe, F., & Wabner, M. (2012) · CIRP Annals · doi:10.1016/j.cirp.2012.03.003 · Cited by 31
Temperature measurement in the ultrasonic-assisted drilling process
Moghaddas, M. A., Yi, A. Y., & Graff, K. F. (2019) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-019-03487-7 · Cited by 31
Prisco, U., Impero, F., & Rubino, F. (2019) · Production Engineering · doi:10.1007/s11740-019-00915-1 · Cited by 31
Tool Wear Classification Using Decision Treesin Stone Drilling Applications: A Preliminary Study
Klaić, M., Staroveški, T., & Udiljak, T. (2014) · Procedia Engineering · doi:10.1016/j.proeng.2014.03.125 · Cited by 30
Eynian, M., Das, K., & Wretland, A. (2017) · High Speed Machining · doi:10.1515/hsm-2017-0001 · Cited by 29
Prediction of a New Form of the Cutting Tool According to Achieve the Desired Surface Quality
Jurko, J., Panda, A., & Behún, M. (2012) · Applied Mechanics and Materials · doi:10.4028/www.scientific.net/amm.268-270.473 · Cited by 28
Study of Manufacturing Defects and Tool Geometry Optimisation for Multi-Material Stack Drilling
Benezech, L., Landon, Y., & Rubio, W. (2011) · Advanced materials research · doi:10.4028/www.scientific.net/amr.423.1 · Cited by 26
Investigating the effects of cutting parameters on the hole quality in drilling the Ti-6Al-4V alloy
Çelik, Y. H. (2014) · Cited by 19
Thermal Effects in Complex Machining Processes
(2017) · Lecture notes in production engineering · doi:10.1007/978-3-319-57120-1 · Cited by 16
Kim, D., Beal, A., Kang, K.-W., & Kim, S.-Y. (2017) · Carbon letters · doi:10.5714/cl.2017.23.001 · Cited by 16
Sauer, K., Dix, M., & Pütz, M. (2018) · Journal of Manufacturing and Materials Processing · doi:10.3390/jmmp2030046 · Cited by 11
A new strategy of carbon fiber reinforced plastic drilling evaluation using thermal measurement
Park, J., Kwon, D.-J., Wang, Z.-J., Gu, G., & DeVries, K. L. (2012) · Journal of Composite Materials · doi:10.1177/0021998312453358 · Cited by 10
STUDY OF THE SUITABILITY OF THE MACHINING OF ROTATING SURFACES
Škorić, S., Udiljak, T., & Ciglar, D. (2008) · Transactions of FAMENA · Cited by 10
Kolesnyk, V., Kryvoruchko, D. V., Hatala, M., Mitaľ, D., Hutyrová, Z., Duplák, J., & Alowa, M. J. A. (2015) · MANUFACTURING TECHNOLOGY · doi:10.21062/ujep/x.2015/a/1213-2489/mt/15/3/357 · Cited by 10
Self-citationMethod of Hole Shrinkage Radial Forces Measurement in Ti6Al4V Drilling
Merzouki, J., Poulachon, G., Rossi, F., Ayed, Y., & Abrivard, G. (2017) · Procedia CIRP · doi:10.1016/j.procir.2017.03.226 · Cited by 9
Gulpak, M., & Sölter, J. (2015) · Procedia CIRP · doi:10.1016/j.procir.2015.03.070 · Cited by 8
Tool Wear and Cutting Temperature at Machining of Composites
Líska, J., & Kodácsy, J. (2011) · Advanced materials research · doi:10.4028/www.scientific.net/amr.325.381 · Cited by 6
Experimental and Simulative Modeling of Drilling Processes for the Compensation of Thermal Effects
Bollig, P., Michna, J., Faltin, C., Schneider, J., Zanger, F., Schießl, R., Maas, U., & Schulze, V. K. (2017) · Lecture notes in production engineering · doi:10.1007/978-3-319-57120-1_9 · Cited by 6
Hardmetals WC–Co Based on Nanocrystalline Powders of Tungsten Carbide WC
Kurlov, A. S., & Gusev, A. I. (2013) · Springer series in materials science · doi:10.1007/978-3-319-00524-9_5 · Cited by 3
Investigation on Drilling Performance of Titanium Alloy Ti6Al4V Based on Response Surface Method
Zhu, Z., Sui, S., Sun, J., Li, J., & Liu, K. (2017) · ASME International Manufacturing Science and Engineering Conference (MSEC) · doi:10.1115/msec2017-2926 · Cited by 2
Research works printed but not linked: 5
- Hassan M.H. Mahmud A.S. Abdulah J. Effects of Twist Drill Geometry and Drilling Parameters on CFRP-Aluminum Stack Up in Single Shot Drilling SciFed Mater. Res. Lett. 2018 2 1 14
- Kumar D. Gururaja S. Experimental Investigation of CFRP/Ti Stack Drilling Under Cryogenic Condition Proceedings of the International Conference on Composite Materials and Structures ICCMS Hyterabad, India 27–29 December 2017
- Kuo C.-L. Aspinwall D. Thomas W. Carr C. Pearson D. M’Saoubi R. Leahy W. Performance of multi-margin coated tools in oneshot shot drilling of metallic-composite stack materials under varying feed rate and pecking conditions Proceedings of the 38th International Matador Conference Yunlin, Taiwan 28–30 March 2015 231 238
- Prasanth R. Senthilkumar M. Prabu K. Krishnaraj V. Identification of Drill Position in CFRP/Titanium alloy Stacks using Acoustic Emission Signals Proceedings of the International Conference on Advances in Materials, Manufacturing and Applications Tamil Nadu, India 9–11 April 2015 1174 1181
- Fox-Rabinovich G. Totten E.G. Self-Organization During Friction Advanved Surface-Engineered Materials and Systems Design CRC Press Boca Raton, FL, USA 2019 459 9780367390365
Cited by
Optimization of CFRP drilling process: a review
Zhu, W., Fu, H., Li, F., Xu, J., Li, Y., & Bai, F. (2022) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-022-10112-7 · Cited by 77
A critical review addressing conventional twist drilling mechanisms and quality of CFRP/Ti stacks
Xu, J., Kolesnyk, V., Li, C., Lysenko, B., Peterka, J., & Gupta, M. K. (2023) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2023.04.226 · Cited by 51
Self-citationKolesnyk, V., Peterka, J., Alekseev, O., Нешта, А., Xu, J., Lysenko, B., Sahul, M., Martinovič, J., & Hrbál, J. (2022) · Materials · doi:10.3390/ma15051940 · Cited by 51
Self-citationKuruc, M., Vopát, T., Peterka, J., Necpál, M., Šimna, V., Milde, J., & Jurina, F. (2022) · Materials · doi:10.3390/ma15020585 · Cited by 38
Self-citationDrilling study on CFRP/Ti-6Al-4V stacks using chip breaker grooved drill
Samsudeensadham, S., & Krishnaraj, V. (2022) · Materials and Manufacturing Processes · doi:10.1080/10426914.2022.2030872 · Cited by 31
Metadata
- Authors
- Kolesnyk, V., Peterka, J., Kuruc, M., Šimna, V., Moravčíková, J., Vopát, T., & Lisovenko, D.
- Affiliations
- Sumy State University (UA)
- Slovak University of Technology in Bratislava (SK)
- Corresponding author
- Peterka, Jozef
- ORCID
- Venue
- Materials
- Publisher
- MDPI AG
- Published
- 2020-07-20
- Volume
- 13
- Issue
- 14
- Pages
- 3232
- ISSN
- 1996-1944 (ISSN-L)
- PMC
- PMC7411704
- OpenAlex
- W3042660210
- Cited by
- 44
- References
- 57
- Citations by year
- 2026: 10 · 2025: 4 · 2024: 2 · 2023: 5 · 2022: 10 · 2021: 11 · 2020: 2
- FWCI
- 3.44
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Materials (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- Electronic Sumy State University Institutional Repository (Sumy State University) (submittedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
- Funders
- Vedecká Grantová Agentúra MŠVVaŠ SR a SAV (1/0019/20)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Engineering Technology and Methodologies
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Advanced Machining and Optimization Techniques
- Keywords
- drilling, drilling temperature, hole accuracy, hole roundness, carbon fiber reinforced polymer, titanium alloys, machinability, finite element analysis, coordinate measuring machine
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.