Response Surface Methodology Analysis of Energy Harvesting System over Pathway Tiles
Open accessThe DOI matches its Crossref record; 32 of the 32 references it cites were found in a registry or an index.
Abstract
This paper presents an experimental analysis of the optimization of PZT-based tiles for energy harvesting. The hardware (actual experiment), PZT-based tiles, were developed using 6 × 6 piezoelectric (PZT—lead zirconate titanate) sensors of 40 mm in diameter on a hard cardboard sheet (300 × 300 mm2). Our experimental analysis of the designed tiles obtained an optimized power of 3.626 mW (85 kg or 0.83 kN using 36 sensors) for one footstep and 0.9 mW for 30 footsteps at high tapping frequency. Theoretical analysis was conducted with software (Design-Expert) using the response surface methodology (RSM) for optimized PZT tiles, obtaining a power of 6784.155 mW at 150 kg or 1.47 kN weight using 34 sensors. This software helped to formulate the mathematical equation for the most suitable PZT tile model for power optimization. It used the quadratic model to provide adjusted and predicted R2 values of 0.9916 and 0.9650, respectively. The values were less than 0.2 apart, which indicates a high correlation between the actual and predicted values. The outcome of the various experiments can help with the selection of input factors for optimized power during pavement design.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Figures







Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The cited source says what the claim attributes to it.
In the citing paper
“Referring to [18, 20, 21] as illustrated in Table 3, it can be noticed that the occupied floor area by such studies is similar to the floor area of this study; however, the harvested power of the proposed floor area is significantly higher.”
From Energy Harvesting Floor Tile Using Piezoelectric Patches for Low-Power Applications (2024) · cites this paper as [20]
The cited source says what the claim attributes to it.
In the citing paper
“Compared to [20, 21], our design utilised fewer piezoelectric patch numbers with higher harvested power.”
From Energy Harvesting Floor Tile Using Piezoelectric Patches for Low-Power Applications (2024) · cites this paper as [20]
The cited source says what the claim attributes to it.
In the citing paper
“[20] employed 36 patches and recorded a harvested power of 3.626 mW, whereas [21] used 44 patches and recorded a harvested power of 35 mW.”
From Energy Harvesting Floor Tile Using Piezoelectric Patches for Low-Power Applications (2024) · cites this paper as [20]
The check wasn’t confident either way, so it gives no verdict — never disputed.
In the citing paper
“Referring to [18, 20, 21] as illustrated in Table 3, it can be noticed that the occupied floor area by such studies is similar to the floor area of this study; however, the harvested power of the proposed floor area is significantly higher.”
From Energy Harvesting Floor Tile Using Piezoelectric Patches for Low-Power Applications (2024) · cites this paper as [20]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Zhu, M., Shi, Q., He, T., Yi, Z., Ma, Y., Yang, B., Chen, T., & Lee, C. (2019) · ACS Nano · doi:10.1021/acsnano.8b08329 · Cited by 411
Piezoelectric energy harvesting systems for biomedical applications
Panda, S., Hajra, S., Mistewicz, K., In-na, P., Sahu, M., Rajaitha, P. M., & Kim, H. J. (2022) · Nano Energy · doi:10.1016/j.nanoen.2022.107514 · Cited by 269
A critical review of roadway energy harvesting technologies
Gholikhani, M., Roshani, H., Dessouky, S., & Papagiannakis, A. T. (2020) · Applied Energy · doi:10.1016/j.apenergy.2019.114388 · Cited by 259 · cited 3×
“Various reviews of novel PEH [13] for pavement applications generated an average output power of 3.106 mW, and importantly, noted that tiles should be protected by plastic material [14–16].”
BackgroundInfluentialPiezoelectric energy harvester for public roadway: On-site installation and evaluation
Xiong, H., & Wang, L. (2016) · Applied Energy · doi:10.1016/j.apenergy.2016.04.031 · Cited by 235
High-Performance PZT-Based Stretchable Piezoelectric Nanogenerator
Niu, X., Jia, W., Qian, S., Zhu, J., Zhang, J., Hou, X., Mu, J., Geng, W., Cho, J., He, J., et al. (2019) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.8b04627 · Cited by 208
A review of piezoelectric energy harvesting tiles: Available designs and future perspective
Sharma, S., Kiran, R., Azad, P., & Vaish, R. (2022) · Energy Conversion and Management · doi:10.1016/j.enconman.2022.115272 · Cited by 194 · cited 1×
“Amongst the various mechanical stress sources, vibrations from human movements are used as the primary and spontaneous power source for PZT floor tiles, which convert them into useful energy [4].”
BackgroundEnergy harvesting in wireless sensor networks: A taxonomic survey
Singh, J., Kaur, R., & Singh, D. (2021) · International Journal of Energy Research · doi:10.1002/er.5816 · Cited by 192
Liu, H., Lin, X., Zhang, S., Huan, Y., Huang, S., & Cheng, X. Y. (2020) · Journal of Materials Chemistry A · doi:10.1039/d0ta03054f · Cited by 105
Modelling piezoelectric energy harvesting potential in an educational building
Li, X., & Strezov, V. (2014) · Energy Conversion and Management · doi:10.1016/j.enconman.2014.05.096 · Cited by 84 · cited 1×
“[27,28] STEP technology using wireless-based PZT Switch on the light and fan Per footstep”
MethodLee, H., Kim, H., Kim, D. Y., & Seo, Y. (2019) · ACS Omega · doi:10.1021/acsomega.8b03325 · Cited by 79
A mathematical model for piezoelectric ring energy harvesting technology from vehicle tires
Xie, X., & Wang, Q. (2015) · International Journal of Engineering Science · doi:10.1016/j.ijengsci.2015.05.004 · Cited by 73 · cited 1×
“[33] Piezoelectric (PE) and electromagnetic harvester (EM) for WSN 1–3.”
BackgroundPanthongsy, P., Isarakorn, D., Janphuang, P., & Hamamoto, K. (2018) · Sensors and Actuators A: Physical · doi:10.1016/j.sna.2018.06.035 · Cited by 63
Design of a pavement using piezoelectric materials
Nia, E. M., Zawawi, N. A. W. A., & Singh, B. S. M. (2019) · Materialwissenschaft und Werkstofftechnik · doi:10.1002/mawe.201900002 · Cited by 61
Floor Tile Energy Harvester for Self-Powered Wireless Occupancy Sensing
Sharpes, N., Vučković, D., & Priya, S. (2016) · Energy Harvesting and Systems · doi:10.1515/ehs-2014-0009 · Cited by 50 · cited 1×
“[22] also reported a novel approach for developing a new PZT material that can be utilized to function as a renewable resource.”
BackgroundHajra, S., Oh, Y., Sahu, M., Lee, K.-T., Kim, H.-G., PANIGRAHI, B. K., Mistewicz, K., & Kim, H. J. (2021) · Sustainable Energy & Fuels · doi:10.1039/d1se01587g · Cited by 45
Pavement energy harvesting technologies: a critical review
Vizzari, D., Gennesseaux, É., Lavaud, S., Bouron, S., & Chailleux, E. (2021) · RILEM Technical Letters · doi:10.21809/rilemtechlett.2021.131 · Cited by 32
Design and Evaluation of Double-Stage Energy Harvesting Floor Tile
Isarakorn, D., Jayasvasti, S., Panthongsy, P., Janphuang, P., & Hamamoto, K. (2019) · Sustainability · doi:10.3390/su11205582 · Cited by 27
Footstep Power Generation Using Piezo-Electric Transducers
Sharma, K., Pikhan, S., Kohli, P., & Khajuria, M. (2017) · International Journal of Scientific Engineering and Research · doi:10.70729/ijser151422 · Cited by 27
Energy harvesting using piezoelectricity
Patil, A., Jadhav, M., Joshi, S., Britto, E., & Vasaikar, A. (2015) · International Conference on Energy Systems and Applications · doi:10.1109/icesa.2015.7503403 · Cited by 23
Assessment of 50 kWp rooftop solar photovoltaic plant at The ICFAI University, Jaipur: A case study
Mukherji, R., Mathur, V., Bhati, A., & Mukherji, M. (2019) · Environmental Progress & Sustainable Energy · doi:10.1002/ep.13353 · Cited by 23 · cited 1×
“Global energy demand is surging due to dramatic urbanization, industrialization, and technological advancements [1].”
BackgroundSelf-citationNuclear Power and Sustainable Energy Policy: Promises and Perils
Kessides, I. N. (2009) · The World Bank Research Observer · doi:10.1093/wbro/lkp010 · Cited by 19 · cited 1×
“The world’s energy consumption is expected to grow by 44% from 2006 to 2030 [2].”
BackgroundPower generation by using piezoelectric transducer with bending mechanism support
Asry, A. M. M., Mustafa, F., Ishak, M., & Ahmad, A. (2019) · International Journal of Power Electronics and Drive Systems (IJPEDS) · doi:10.11591/ijpeds.v10.i1.pp562-567 · Cited by 19 · cited 1×
“[26] PZT with bending mechanism Single sensor with different diameters (30, 40, and 50 mm) 19, 34.”
BackgroundSarker, M. R., Mohamed, R., Saad, M. H. M., Tahir, M., Hussain, A., & Mohamed, A. (2021) · Electronics · doi:10.3390/electronics10010075 · Cited by 15 · cited 1×
“[31] triboelectric energy harvester (TEH) 25 V for 0.”
BackgroundEnergy Harvesting through Floor Tiles
Ahmed, S. U., Sabir, A., Ashraf, T., Haider, M. A., Perveen, F., Farooqui, Z., & Uddin, R. (2019) · International Conference on Innovative Computing (ICIC) · doi:10.1109/icic48496.2019.8966706 · Cited by 13 · cited 1×
“[34] 44 PZTs with cantilever 35 mWrms 50 kG”
Modeling and parametric analysis for performance improvement in piezoelectric energy harvesting tile
Adhikari, J., Kumar, R., & Jain, S. C. (2021) · Ferroelectrics · doi:10.1080/00150193.2021.1890477 · Cited by 10 · cited 1×
“[8] conducted a PZT performance analysis in terms of power using parameters such as frequency, tip mass, and EIDC.”
MethodWang, S.-H., Tsai, M., & Wu, T.-H. (2021) · Crystals · doi:10.3390/cryst11040380 · Cited by 9 · cited 1×
“[29] S-sock using hybrid polymer and PZT chip 1.”
MethodCost effectiveness of piezo electric energy harvesting
Kar, S., Samanth, K., & Raghunandana, K. (2021) · Materials Today Proceedings · doi:10.1016/j.matpr.2020.11.220 · Cited by 8 · cited 1×
“[7] presented a tire that could be used for energy harvesting and conducted a cost analysis and power estimation for a vehicle.”
MethodPiezoelectric impact-driven energy harvester
Abdal-Kadhim, A. M., & Leong, K. S. (2016) · IEEE International Conference on Power and Energy · doi:10.1109/pecon.2016.7951596 · Cited by 6 · cited 1×
“[23] PZT-based 50 V 80 N [5] PZT-based 72 15–18 V, 0.”
Harvesting Electricity using Piezoelectric Material in Malls
Rumman, H., Guangul, F. M., Abdu, A., Usman, M., & Alkharusi, A. (2019) · MEC International Conference on Big Data and Smart City (ICBDSC) · doi:10.1109/icbdsc.2019.8645581 · Cited by 6 · cited 1×
“[6] developed tiles using PZT sensors for the mall to harvest the energy at the entrance gate by person movement.”
MethodOptimized Hybrid Electricity Generation
Gothwal, P., Palliwal, P., & Shubhangi (2021) · Algorithms for intelligent systems · doi:10.1007/978-981-15-6707-0_31 · Cited by 4
Self-citationGENERATING ELECTRICITY BY FOOTPATH POWER GENERATOR FLOOR TILES
al., R. M. E. (2021) · INFORMATION TECHNOLOGY IN INDUSTRY · doi:10.17762/itii.v9i2.389 · Cited by 4 · cited 1×
“[30] piezo sensor-based cantilever energy (0.”
Power generation improvement for piezoelectric energy harvesting for roadsides sustainability
Ahad, M. A., Kim, S., Shen, J., Rice, D., & Stern, I. (2017) · IEEE SoutheastCon · doi:10.1109/secon.2017.7925288 · Cited by 3 · cited 2×
“[23] PZT-based 50 V 80 N [5] PZT-based 72 15–18 V, 0.”
Background
Research works printed but not linked: 1
- Shreeshayana R. Raghavendra L. Manjunath V.G. Piezoelectric Energy Harvesting using PZT in Floor Tile Design Int. J. Adv. Res. Electr. Electron. Instrum. Eng. 2017 6 8872 8879
Cited by
Energy Harvesting Floor Tile Using Piezoelectric Patches for Low-Power Applications
Selim, K. K., Yehia, H. M., & Saleeb, D. A. (2024) · Journal of Vibration Engineering & Technologies · doi:10.1007/s42417-024-01379-z · Cited by 15
“…36 patches and recorded a harvested power of 3.626 mW, whereas [21] used 44 patches and recorded a harvested power of 35 mW. Referring to [18, 20, 21] as illustrated in Table 3, it can be noticed that the occupied floor area by such studies is similar to the floor area of this study;…”
InfluentialWang, C., Wang, J., Yuan, H., Wang, S., Niu, Y., & Liu, J. (2025) · Energy · doi:10.1016/j.energy.2025.138959 · Cited by 3
Jegadeesan, K., & Shankar, K. (2024) · Mechanics of Advanced Materials and Structures · doi:10.1080/15376494.2024.2443814 · Cited by 3
Harvesting electricity from road traffic noise energy – a literature review
Tanzadeh, R., Torbaghan, M. E., Venetsaneas, N., & Nejad, F. M. (2024) · Proceedings of the Institution of Civil Engineers - Transport · doi:10.1680/jtran.23.00057 · Cited by 3
Khafaga, D. S., El‐kenawy, E. M., Khodadadi, N., Alhussan, A. A., & Eid, M. M. (2025) · Energy Reports · doi:10.1016/j.egyr.2025.09.017 · Cited by 2
Metadata
- Authors
- Gothwal, P., Kumar, A., Rathore, D., Mukherji, R., Vetriselvi, T., & Anandan, S.
- Affiliations
- Manipal University Jaipur (IN)
- Amity University Jaipur (IN)
- Institute of Chartered Financial Analysts of India University, Jaipur (IN)
- Vellore Institute of Technology University (IN)
- Department of Chemistry, National Institute of Technology, Trichy 620015, Tamil Nadu, India
- Corresponding author
- Gothwal, P.
- Anandan, S.
- Venue
- Materials
- Publisher
- MDPI AG
- Published
- 2023-01-29
- Volume
- 16
- Issue
- 3
- Pages
- 1146
- ISSN
- 1996-1944 (ISSN-L)
- PMC
- PMC9919019
- OpenAlex
- W4318465141
- Cited by
- 9
- References
- 32
- Citations by year
- 2025: 3 · 2024: 4 · 2023: 2
- FWCI
- 0.89
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Materials (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Innovative Energy Harvesting Technologies
- Physical Sciences › Engineering › Biomedical Engineering › Advanced Sensor and Energy Harvesting Materials
- Physical Sciences › Engineering › Mechanics of Materials › Ultrasonics and Acoustic Wave Propagation
- Keywords
- piezoelectric energy harvesting, response surface methodology, power optimization, quadratic model, pavement design, tapping frequency
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.