The DOI matches its Crossref record; 134 of the 143 references it cites were found in a registry or an index.
Post-Processing Techniques to Enhance the Quality of Metallic Parts Produced by Additive Manufacturing
Open accessAbstract
Additive manufacturing (AM) processes can produce three-dimensional (3D) near-net-shape parts based on computer-aided design (CAD) models. Compared to traditional manufacturing processes, AM processes can generate parts with intricate geometries, operational flexibility and reduced manufacturing time, thus saving time and money. On the other hand, AM processes face complex issues, including poor surface finish, unwanted microstructure phases, defects, wear tracks, reduced corrosion resistance and reduced fatigue life. These problems prevent AM parts from real-time operational applications. Post-processing techniques, including laser shock peening, laser polishing, conventional machining methods and thermal processes, are usually applied to resolve these issues. These processes have proved their capability to enhance the surface characteristics and physical and mechanical properties. In this study, various post-processing techniques and their implementations have been compiled. The effect of post-processing techniques on additively manufactured parts has been discussed. It was found that laser shock peening (LSP) can cause severe strain rate generation, especially in thinner components. LSP can control the surface regularities and local grain refinement, thus elevating the hardness value. Laser polishing (LP) can reduce surface roughness up to 95% and increase hardness, collectively, compared to the as-built parts. Conventional machining processes enhance surface quality; however, their influence on hardness has not been proved yet. Thermal post-processing techniques are applied to eliminate porosity up to 99.99%, increase corrosion resistance, and finally, the mechanical properties’ elevation. For future perspectives, to prescribe a particular post-processing technique for specific defects, standardization is necessary. This study provides a detailed overview of the post-processing techniques applied to enhance the mechanical and physical properties of AM-ed parts. A particular method can be chosen based on one’s requirements.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“For metals and metal matrix composites (MMCs), it can include annealing, hardening (quenching), aging, and stress relieving, among others [381,382,384].”
From A comprehensive review of lunar-based manufacturing and construction (2024) · cites this paper as [382]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Metal Additive Manufacturing: A Review
Frazier, W. E. (2014) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-014-0958-z · Cited by 5,984
The metallurgy and processing science of metal additive manufacturing
Sames, W. J., List, F. A., Pannala, S., Dehoff, R., & Babu, S. S. (2016) · International Materials Reviews · doi:10.1080/09506608.2015.1116649 · Cited by 2,685
Thijs, L., Kempen, K., Kruth, J., & Humbeeck, J. V. (2012) · Acta Materialia · doi:10.1016/j.actamat.2012.11.052 · Cited by 1,925
Additive Manufacturing Technologies
Gibson, I., Rosen, D. W., Stucker, B. E., & Khorasani, M. (2020) · Springer eBooks · doi:10.1007/978-3-030-56127-7 · Cited by 1,902
Aboulkhair, N. T., Simonelli, M., Parry, L., Ashcroft, I., Tuck, C. J., & Hague, R. (2019) · Progress in Materials Science · doi:10.1016/j.pmatsci.2019.100578 · Cited by 1,622
Zhang, J., Song, B., Wei, Q., Bourell, D. L., & Shi, Y. (2018) · Journal of Material Science and Technology · doi:10.1016/j.jmst.2018.09.004 · Cited by 1,215
Brandl, E., Heckenberger, U., Holzinger, V., & Buchbinder, D. (2011) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2011.07.067 · Cited by 1,154
Rappaz, M., Drezet, J. M., & Gremaud, M. (1999) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-999-0334-z · Cited by 1,080
Selective laser melting of aluminium components
Louvis, E., Fox, P., & Sutcliffe, C. J. (2010) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2010.09.019 · Cited by 938
Binder jetting: A review of process, materials, and methods
Ziaee, M., & Crane, N. B. (2019) · Additive manufacturing · doi:10.1016/j.addma.2019.05.031 · Cited by 908
Research works printed but not linked: 1
- Alloy, 2020, A Review on Laser Powder Bed Fusion of Inconel 625, Appl. Sci., 10, 81
Cited by
Sorted by citations
Çam, G., & Günen, A. (2024) · Journal of Magnesium and Alloys · doi:10.1016/j.jma.2024.05.004 · Cited by 213
Motallebi, R., Savaedi, Z., & Mirzadeh, H. (2022) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2022.07.154 · Cited by 113
Additive manufacturing in the new space economy: Current achievements and future perspectives
Ghidini, T., Grasso, M., Gumpinger, J., Makaya, A., & Colosimo, B. M. (2023) · Progress in Aerospace Sciences · doi:10.1016/j.paerosci.2023.100959 · Cited by 87
Laser Additive Manufacturing of High-Strength Aluminum Alloys: Challenges and Strategies
Dixit, S., & Liu, S. (2022) · Journal of Manufacturing and Materials Processing · doi:10.3390/jmmp6060156 · Cited by 76
Farias, F. W. C., Santos, T. G., & Oliveira, J. P. (2024) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-024-13126-5 · Cited by 67
Świetlicki, A., Szala, M., & Walczak, M. (2022) · Materials · doi:10.3390/ma15072476 · Cited by 66
Challenges and developments in wire arc additive manufacturing of steel: A review
Dekis, M., Tawfik, M. M., Egiza, M., & Dewidar, M. (2025) · Results in Engineering · doi:10.1016/j.rineng.2025.104657 · Cited by 62
Multimetal Research in Powder Bed Fusion: A Review
Yao, L., Ramesh, A., Xiao, Z., Chen, Y., & Zhuang, Q. (2023) · Materials · doi:10.3390/ma16124287 · Cited by 58
A comprehensive review of lunar-based manufacturing and construction
Azami, M., Kazemi, Z., Moazen, S., Dubé, M., Potvin, M.-J., & Skonieczny, K. (2024) · Progress in Aerospace Sciences · doi:10.1016/j.paerosci.2024.101045 · Cited by 57
Additive Manufacturing in the Context of Repeatability and Reliability
Venturi, F., & Taylor, R. M. (2023) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-023-07897-3 · Cited by 61
Mushtaq, R. T., Wang, Y., Khan, A. M., Rehman, M., Li, X., & Sharma, S. (2023) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2023.06.019 · Cited by 49
Mushtaq, R. T., Wang, Y., Bao, C., Chen, X., Anwar, S., Sharma, S. K., Khan, A. M., Sharma, K., Bisht, Y. S., Abbas, M. A. E., et al. (2024) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2024.02.023 · Cited by 47
Шарма, С. К., Grewal, H. S., Saxena, K. K., Mohammed, K. A., Prakash, C., Davim, J. P., Buddhi, D., Raju, R., Mohan, D. G., & Tomków, J. (2022) · Materials · doi:10.3390/ma15228122 · Cited by 46
High-throughput screening of surface roughness during additive manufacturing
Du, Y., Mukherjee, T., Finch, N. W., De, A., & DebRoy, T. (2022) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2022.06.049 · Cited by 44
Mushtaq, R. T., Iqbal, A., Wang, Y., Khan, A. M., & Petra, M. I. (2023) · Crystals · doi:10.3390/cryst13040626 · Cited by 41
Advancements in cellulose nanocrystals: A review of functionalization, applications, and challenges
Aziz, T., Rohullah, R., Ullah, A., Zeb, U., Hussain, M. A., Ali, A., Haq, F., & Kiran, M. (2025) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2025.144552 · Cited by 43
Parametric optimization of 3D printing process hybridized with laser-polished PETG polymer
Mushtaq, R. T., Iqbal, A., Wang, Y., Khan, A. M., & Bakar, M. S. A. (2023) · Polymer Testing · doi:10.1016/j.polymertesting.2023.108129 · Cited by 39
On the applications of additive manufacturing in semiconductor manufacturing equipment
Ye, J., Desouky, A. E., & Elwany, A. H. (2024) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2024.05.054 · Cited by 39
Singh, S. N., & Deoghare, A. B. (2022) · Metals and Materials International · doi:10.1007/s12540-022-01334-1 · Cited by 39
A review of laser polishing on Ti6Al4V based on energy density
Lu, H., Wang, D., Wu, S., Pan, Z., Wang, G., Guo, G., Tian, Y., & Xiang, D. (2024) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2024.118520 · Cited by 43
Investigation of the Properties of 316L Stainless Steel after AM and Heat Treatment
Petroušek, P., Kvačkaj, T., Bidulská, J., Bidulský, R., Grande, M., Manfredi, D., Weiss, K., Kočiško, R., Lupták, M., & Pokorný, I. (2023) · Materials · doi:10.3390/ma16113935 · Cited by 30
Fu, X., Li, S., Song, H., & Lu, Y. (2024) · Robotics and Computer-Integrated Manufacturing · doi:10.1016/j.rcim.2024.102902 · Cited by 33
The Post-Processing of Additive Manufactured Polymeric and Metallic Parts
Syrlybayev, D., Seisekulova, A., Talamona, D., & Perveen, A. (2022) · Journal of Manufacturing and Materials Processing · doi:10.3390/jmmp6050116 · Cited by 28
Mahajan, A., & Devgan, S. (2024) · Progress in Additive Manufacturing · doi:10.1007/s40964-024-00722-w · Cited by 23
Chioibasu, D., Mihai, S., Cotruț, C. M., Voiculescu, I., & Popescu, A. C. (2022) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-022-09646-7 · Cited by 23
Self-citationBehjat, A., Shamanian, M., Taherizadeh, A., Lannunziata, E., Bagherifard, S., Gadalińska, E., Saboori, A., & Iuliano, L. (2023) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2023.01.229 · Cited by 18
Digonta, H. M. D. A., & Fatemi, A. (2024) · Theoretical and Applied Fracture Mechanics · doi:10.1016/j.tafmec.2024.104281 · Cited by 21
Metal additive manufacturing for particle accelerator applications
Romano, T., Pikurs, G., Ratkus, A., Torims, T., Delerue, N., Vretenar, M., Stepien, L., López, E., & Vedani, M. (2024) · Physical Review Accelerators and Beams · doi:10.1103/physrevaccelbeams.27.054801 · Cited by 23
Vats, P., Kumar, A., & Gajrani, K. K. (2024) · Machining Science and Technology · doi:10.1080/10910344.2024.2381206 · Cited by 20
Mosallanejad, M. H., Ghanavati, R., Behjat, A., Taghian, M., Saboori, A., & Iuliano, L. (2024) · Metals · doi:10.3390/met14040425 · Cited by 19
Ramadas, H., Sarkar, S., Ganesh, P., Kaul, R., Majumdar, J. D., & Nath, A. K. (2023) · Materials Science and Engineering A · doi:10.1016/j.msea.2023.144657 · Cited by 19
Razavi, N., Bagherifard, S., Hafnor, S., Spiller, S., Guagliano, M., & Berto, F. (2023) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2023.108041 · Cited by 19
Gracheva, A., Анатольевич, П. И., & Popovich, A. (2025) · Metals · doi:10.3390/met15070754 · Cited by 18
Fischmann, P., Schrauth, F., & Zanger, F. (2023) · CIRP Annals · doi:10.1016/j.cirp.2023.04.018 · Cited by 14
Partial Biodegradable Blend with High Stability against Biodegradation for Fused Deposition Modeling
Harris, M., Mohsin, H., Potgieter, J., Ishfaq, K., Archer, R. H., Chen, Q., Silva, K. D., Guen, M.-J. L., Wilson, R., & Arif, K. M. (2022) · Polymers · doi:10.3390/polym14081541 · Cited by 14
Welding-based additive manufacturing processes for fabrication of metallic parts
Rathinasuriyan, C., Elumalai, P., Chandar, J. B., Karthik, K., Medapati, S. R., Alahmadi, A. A., Alwetaishi, M., Alzaed, A., Kalam, M. A., & Shahapurkar, K. (2023) · Composites and Advanced Materials · doi:10.1177/26349833231210572 · Cited by 12
Xue, X.-Y., Bao, J.-G., Wu, Z.-K., Zhao, Y., Da, R., Yang, D.-B., Wu, S.-C., Burnett, T. L., & Withers, P. J. (2026) · Materials science & engineering. R, Reports · doi:10.1016/j.mser.2026.101197 · Cited by 12
Meena, R., Hashmi, A. W., Iqbal, F., Ahmad, S., Prakash, C., Katiyar, J. K., Mali, H. S., & Meena, A. (2024) · Physica Scripta · doi:10.1088/1402-4896/ad5a52 · Cited by 10
Friction and Wear Behavior of 3D-Printed Inconel 718 Alloy under Dry Sliding Conditions
Karagiannidis, I., Tzanis, A., Drees, D., Lopes, L., Chondrakis, G., Dardavila, M. M., Georgiou, E. P., & Koutsomichalis, A. M. (2024) · Coatings · doi:10.3390/coatings14081029 · Cited by 10
Wang, J., Ni, X., Sun, Q. H., Zhang, D., Chen, L., Jin, X. M., Cheng, H., Wang, J., Hong, Y., & Yang, J. (2025) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2025.02.030 · Cited by 10
Lesyk, D., Mordyuk, B. N., Martı́nez, S., Dzhemelinskyi, V., Grochała, D., Kоtkо, А. V., & Lamíkiz, A. (2025) · Coatings · doi:10.3390/coatings15040425 · Cited by 10
Mahmood, M. A., Rehman, A. U., Ristoscu, C., Demir, M., Popescu‐Pelin, G., Pıtır, F., Salamci, M. U., & Mihailescu, I. N. (2022) · Nanomaterials · doi:10.3390/nano12050802 · Cited by 10
Self-citationThe impact of Additive Manufacturing on supply chain resilience: a Delphi study
Peron, M., Saporiti, N., Coruzzolo, A. M., Lolli, F., & Holmström, J. (2025) · Technological Forecasting and Social Change · doi:10.1016/j.techfore.2025.124231 · Cited by 11
Behjat, A., Lannunziata, E., Gadalińska, E., Iuliano, L., & Saboori, A. (2023) · Procedia CIRP · doi:10.1016/j.procir.2023.06.132 · Cited by 9
Hashmi, A. W., Mali, H. S., Meena, A., Saxena, K. K., Puerta, A. P. V., Rao, U. S., Buddhi, D., & Mohammed, K. A. (2022) · International Journal on Interactive Design and Manufacturing (IJIDeM) · doi:10.1007/s12008-022-01048-z · Cited by 9
Dasari, J., & Xavior, M. A. (2026) · Discover Mechanical Engineering · doi:10.1007/s44245-026-00189-9 · Cited by 7
Wasik, A., Leszczyńska‐Madej, B., & Madej, M. (2023) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2023.04.009 · Cited by 7
Metal Based Additive Manufacturing
Dasdemir, U., & Altaş, E. (2023) · Materials horizons · doi:10.1007/978-981-99-5949-5_4 · Cited by 6
Kushwaha, A. K., Misra, M., & Menezes, P. L. (2025) · Lubricants · doi:10.3390/lubricants13090386 · Cited by 6
Review: Laser shock processing technique on the additive manufactured metallic alloys
Lin, X., Liang, C., Li, Y., Geng, Y., Chen, Z., Zhao, Y., Chen, X., Wu, J., & Wu, S. (2024) · Journal of Laser Applications · doi:10.2351/7.0001411 · Cited by 6
Hussain, S. Z., Kausar, Z., Koreshi, Z. U., Shah, M. F., Abdullah, A., & Farooq, M. U. (2023) · Electronics · doi:10.3390/electronics12020471 · Cited by 6
Sleiman, K., Sleiman, O., Rettschlag, K., Jäschke, P., & Kaierle, S. (2024) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-024-14586-5 · Cited by 5
Zhao, H., Li, H., Zhang, X., Li, J., Xiong, B., Yuan, Y., Ruan, Y., Zheng, F., Zhang, R., Zhang, W. D., et al. (2025) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2025.3569591 · Cited by 10
Laser additive manufacturing of Co-Cr alloy and the induced defects thereof
Mahmood, M. A., Rehman, A. U., Lungu, M., Pıtır, F., Salamci, M. U., Ristoscu, C., Tiseanu, I., & Mihailescu, I. N. (2022) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-022-09395-7 · Cited by 5
Self-citationAdditive Manufacturing of Nanoscale and Microscale Materials
Kumar, D. V., Srinivasan, N., Hans, S. J. D., Gokul, S., Arulmurugan, B., & Sathishkumar, B. (2024) · doi:10.1002/9781394198085.ch8 · Cited by 5
Revilla, R. I., Baert, K., & Graeve, I. D. (2025) · Corrosion Science · doi:10.1016/j.corsci.2025.113147 · Cited by 4
Innovative Machining Strategies for Metal Matrix Composites: Trends and Future Prospects
Ogunbiyi, O., Jamiru, T., Jeje, S. O., Sanusi, K. O., & Shongwe, M. B. (2025) · Advances in Materials Science and Engineering · doi:10.1155/amse/9958173 · Cited by 4
Favi, C., Murgese, L., Gallozzi, S., Chiacchietta, C., Marconi, M., & Mandolini, M. (2025) · International Journal on Interactive Design and Manufacturing (IJIDeM) · doi:10.1007/s12008-025-02432-1 · Cited by 4
Manikandan, P., & Venkatesan, K. (2026) · Proceedings of the Institution of Mechanical Engineers Part L Journal of Materials Design and Applications · doi:10.1177/14644207251413481 · Cited by 4
Gupta, M. K. (2026) · Precision Engineering · doi:10.1016/j.precisioneng.2026.02.005 · Cited by 4
Rad, S. M. M., Hajialimohammadi, A., & Abedini, V. (2024) · Progress in Additive Manufacturing · doi:10.1007/s40964-024-00716-8 · Cited by 4
Aluminum Bronze Crystallization on Deformed Base during Electron Beam Additive Manufacturing
Nikonov, A. Y., Lychagin, D. V., Bibko, A. A., & Novitskaya, O. S. (2023) · Metals · doi:10.3390/met13061012 · Cited by 4
Luft, A., Bremen, S., & Luft, N. (2023) · Processes · doi:10.3390/pr11071968 · Cited by 4
Innovative Post-Processing for Complex Geometries and Inner Parts of 3D-Printed AlSi10Mg Devices
Calvet, M., Domènech, A., Vilaró, S., Meseguer, T., & Bautista, L. (2023) · Materials · doi:10.3390/ma16217040 · Cited by 4
Demisse, W., Guerrero, P. S., Fulford, D., Rice, L., Klein, K. L., & Tyagi, P. (2024) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-024-14217-z · Cited by 4
Advancement of Magnesium and Aluminum Alloys in the Role of Additive ManufacturingPreprint
Sharma, S. K., Grewal, H. S., Saxena, K. K., Mohammed, K. A., Prakash, C., Davim, J. P., Buddhi, D., Raju, R., Mohan, D. G., & Tomków, J. (2022) · Preprints.org · doi:10.20944/preprints202209.0459.v1 · Cited by 4
Recent advances toward damage-tolerant 3D-printed titanium alloys: Alloy design perspective
Alipour, S., Emdadi, A., & Li, J. (2026) · Journal of Applied Physics · doi:10.1063/5.0287936 · Cited by 3
Far, N. M., Aghdam, R. M., Mirzadeh, H., Asl, F. G., & Najjari, A. (2026) · Materials Chemistry and Physics · doi:10.1016/j.matchemphys.2026.132219 · Cited by 3
A novel framework for identification of cyber-physical attacks in additive manufacturing
Mahmood, M. A., Malik, A. W., & Liou, F. (2024) · Progress in Additive Manufacturing · doi:10.1007/s40964-024-00726-6 · Cited by 3
Self-citationYadav, R., Yadav, S., Dhiman, R., & Patel, R. R. (2024) · Journal of Failure Analysis and Prevention · doi:10.1007/s11668-024-02032-3 · Cited by 3
Chui, E. C., Mak, K. F. H., Ng, R. H., Fung, E., Chan, M., Yue, K., Lau, L. C., Chan, C. L., Yau, E. W. F., Zhao, W. G., et al. (2024) · Orthopaedic Surgery · doi:10.1111/os.14274 · Cited by 3
Godinez, D., Doris, A., Arrieta, E., Murr, L. E., Katsarelis, C., Gradl, P., Lopes, A. J., & Medina, F. R. (2025) · Advances in Industrial and Manufacturing Engineering · doi:10.1016/j.aime.2025.100169 · Cited by 2
Additive Manufacturing (AM): the future of sustainable manufacturing
Khan, M., Shah, K., Khan, A., Yasmeen, T., & Khan, M. K. ;. P. D. I. M. D. (2026) · Elsevier eBooks · doi:10.1016/b978-0-443-32880-0.00013-9 · Cited by 2
Narasimharaju, S. J., & Veeman, D. (2026) · Journal of Power Sources · doi:10.1016/j.jpowsour.2026.241253 · Cited by 2
Kocaarslan, Ş. E., Sağbaş, B., & Durakbasa, M. N. (2023) · Lecture notes in mechanical engineering · doi:10.1007/978-3-031-24457-5_49 · Cited by 2
Wearing Resistance of Metal Coating Layers after Laser Beam Heat Treatment
Olàh, A., Machedon-Pisu, T., & Vizureanu, P. (2023) · Coatings · doi:10.3390/coatings13091645 · Cited by 2
Postprocessing optimization for surface finishing by machine learning
Zhu, H., Zheng, G., Tian, Y., Higham, R., & Rennie, A. (2025) · Elsevier eBooks · doi:10.1016/b978-0-443-22145-3.00008-6 · Cited by 2
Liu, Y., Yan, Z., Lv, J., & Xu, Z. (2025) · Materials Today Communications · doi:10.1016/j.mtcomm.2025.111883 · Cited by 2
Mass Finishing of Ti–6Al–4V Additively Manufactured by Laser Metal Deposition with Powder Process
Ernould, C., Jay, M., Auger, J., Lesseur, J., & Tranchand, B. (2025) · Advanced Engineering Materials · doi:10.1002/adem.202402882 · Cited by 2
Gallego, D. A., Oliveira, H. R., da Cunha, T. V., Pacheco, J. T., Kovalenko, O., & Volpato, N. (2025) · Journal of Manufacturing and Materials Processing · doi:10.3390/jmmp9080254 · Cited by 2
Vedani, M. (2025) · Springer series in materials science · doi:10.1007/978-3-031-97125-9_5 · Cited by 2
Kumar, S., Gao, S. F., Goyal, M., Jindal, T., Kumar, M., Sharma, A., Bhardwaj, S., & Sharma, A. (2025) · Journal of Intelligent Manufacturing · doi:10.1007/s10845-025-02690-6 · Cited by 2
Strategic Production Process Design With Additive Manufacturing in a Make-to-Stock Environment
Chua, P. C., Moon, S. K., Ng, Y. T., & Lopez, M. (2023) · Journal of Manufacturing Science and Engineering · doi:10.1115/1.4063285 · Cited by 2
Enhancing corrosion resistance of lightweight metal alloys through laser shock peening
Huang, W., Leister, B. M., Shen, N., McKee, A., Mubeen, S., Bonheyo, G. T., Rohatgi, A., & Ding, H. (2024) · Journal of Laser Applications · doi:10.2351/7.0001541 · Cited by 1
Tribological Study on Burnished Surface of Additive Manufactured C300 Metal
Travieso-Disotuar, A., Jerez‐Mesa, R., Travieso-Rodriguez, J. A., & Vilaseca, M. (2025) · Key engineering materials · doi:10.4028/p-fghj2n · Cited by 1
Salami, B. R., & Otanocha, O. B. (2025) · Springer eBooks · doi:10.1007/978-3-031-81619-2_19 · Cited by 1
Importance of surface roughness to the performance of additively-manufactured magnets
Ahmad, S., Chen, F., & Rab, S. (2026) · Measurement Science and Technology · doi:10.1088/1361-6501/ae671e · Cited by 1
Mehta, A., Vasudev, H., Kumar, R. S., Singh, J., Prasad, B., Singh, S., Ramesha, H., & Prasad, C. D. (2026) · Canadian Metallurgical Quarterly · doi:10.1080/00084433.2026.2674528 · Cited by 1
Pedroso, A. F. V., Silva, L., Barbosa, M. L. S., Ding, W., Zhao, B., Qian, N., & Silva, F. J. G. (2026) · Journal of Functional Biomaterials · doi:10.3390/jfb17080365 · Cited by 1
A review of the effects of laser shock peening on properties of additively manufactured Ti6Al4V
Kanganga, M., du Plessis, A., Muvunzi, R., & Khodja, M. (2024) · Elsevier eBooks · doi:10.1016/b978-0-323-91204-4.00011-3 · Cited by 1
Lim, B., Provosty, R., & Dong, G. (2024) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-024-13974-1 · Cited by 1
Simulation of deformation and growth during surfacing of aluminum bronze nanograins
Nikonov, A. Y., Lychagin, D. V., Bibko, A. A., & Novitskaya, O. S. (2022) · Letters on Materials · doi:10.22226/2410-3535-2022-4-354-359 · Cited by 1
Postprocessing of Additively Manufactured Polymeric and Metallic Parts—A Review
Mishra, V., Cherian, N. A., Negi, S., & Kar, S. (2024) · doi:10.1002/9781394198085.ch7 · Cited by 1
Pós-processamento de peças metálicas produzidas por manufatura aditiva
Souza, A. M. (2023) · Digital Library of Theses and Dissertations (Universidade de São Paulo) · doi:10.11606/t.18.2023.tde-16052023-092134
A production scheduling case study solved for Electron Beam Powder Bed Fusion
Pastore, E., Galati, M., Alfieri, A., & Iuliano, L. (2024) · IFAC-PapersOnLine · doi:10.1016/j.ifacol.2024.09.148
A Comprehensive Review of Synthetic Polymers and Composites for 3D Bioprinting Applications
Ror, C. K., Mishra, V., & Negi, S. (2024) · Lecture notes in mechanical engineering · doi:10.1007/978-981-97-7535-4_48
Baali, L., Omidi, N., Barka, N., & Dassylva‐Raymond, V. (2025) · Advances in Materials and Processing Technologies · doi:10.1080/2374068x.2025.2449774
Laser-based multimaterial additive manufacturing
Vișan, A. I., & Hapenciuc, C. (2025) · Elsevier eBooks · doi:10.1016/b978-0-443-29228-6.00013-x
Thermal and Mechanical Analysis of Materials in Additive Manufacturing
Boopathy, G., Srinivasan, V., Krasņikovs, A., & Ganesan, B. (2025) · IGI Global eBooks · doi:10.4018/979-8-3373-0533-2.ch008
Characterization Techniques for Four Dimensional (4D) Printed Parts
Samal, B. B., Marupalli, B. C. G., Talukdar, P., Jena, A., Korrayi, R. R., Adhikary, T., Varshney, S. K., & Kumar, C. S. (2025) · doi:10.1002/9781394213795.ch8
Metadata
- Authors
- Mahmood, M. A., Chioibasu, D., Ur Rehman, A., Mihai, S., & Popescu, A. C.
- Affiliations
- National Institute for Laser Plasma and Radiation Physics (RO)
- Organize Sanayi Bölgesi, ERMAKSAN, 16065 Bursa, Turkey
- Corresponding author
- Popescu, Andrei C.
- Venue
- Metals
- Publisher
- MDPI AG
- Published
- 2022-01-04
- Volume
- 12
- Issue
- 1
- Pages
- 77
- ISSN
- 2075-4701 (ISSN-L)
- OpenAlex
- W4206802320
- Cited by
- 119
- References
- 143
- Citations by year
- 2026: 26 · 2025: 28 · 2024: 28 · 2023: 23 · 2022: 14
- FWCI
- 8.77
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Metals (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- European Union’s Horizon 2020 (H2020) research and innovation program under the Marie Skłodowska-Curie (764935)
- Romanian Ministry of Education and Research, under Romanian National Nucleu Program LAPLAS VI (16N/2019)
- POC-G (135/2016)
- Unitatea Executiva Pentru Finantarea Invatamantului Superior a Cercetarii Dezvoltarii si Inovarii (PCE57/2021, PED514/2020)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Additive Manufacturing Materials and Processes
- Physical Sciences › Engineering › Mechanical Engineering › Surface Treatment and Residual Stress
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Additive Manufacturing and 3D Printing Technologies
- Keywords
- additive manufacturing, post-processing, laser shock peening, laser polishing, conventional machining, thermal post-processing, surface roughness, hardness, grain refinement, porosity elimination, corrosion resistance, mechanical properties, metal parts, defects
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
