The DOI matches its Crossref record; 99 of the 101 references it cites were found in a registry or an index; 74 of the 216 sources its claims cite were checked for support.
Recent Advances in Metal-Oxide-Based Photoresists for EUV Lithography
Open accessAbstract
Extreme ultraviolet lithography (EUVL) is a leading technology in semiconductor manufacturing, enabling the creation of high-resolution patterns essential for advanced microelectronics. This review highlights recent progress in inorganic metal-oxide-based photoresists, with a focus on their applications in EUVL. The unique properties of zinc-based, tin-oxygen, and IVB group inorganic photoresists are examined, showcasing their enhanced chemical reactivity and precise patterning capabilities. Key advancements include the development of zinc oxide and tin oxide nanoparticles, which demonstrate significant improvements in photon absorption and solubility under extreme ultraviolet exposure. Additionally, the review delves into the photochemical reactions of tin-oxygen clusters and the influence of various ligands on film density and cross-linking. The findings suggest that these inorganic photoresists not only improve photolithographic performance but also hold potential for broader applications, such as pyroelectric infrared sensors and 3D printing. Future research directions are outlined, including the optimization of process parameters, the exploration of new ligand and metal combinations, and the evaluation of the environmental benefits of inorganic photoresists over traditional organic ones. These advancements are poised to further enhance the resolution and patterning capabilities required for next-generation semiconductor devices.
Overview
CoChat Summary
TL;DR
This review summarizes recent progress in inorganic metal-oxide-based photoresists for extreme ultraviolet lithography (EUVL), focusing on zinc-based, tin–oxygen, and IVB group materials. It reports improved EUV absorption, patterning performance, and broader application potential, while outlining future research directions.
Key findings
- Metal-oxide resists absorb EUV more efficiently than organic polymers: tin–oxide photoresists showed absorption coefficients 2 to 3 times greater than polymer-based resists, and hafnium-based material (HfM) had an absorption coefficient of about 9.0 µm−1 versus 4.8 µm−1 for a standard organic CAR.
- Zn(MA)(TFA) photoresist formed dense line/space patterns with half-pitches from 22 to 50 nm at a low exposure dose of around 20 mJ/cm2, with aspect ratios of 1:3 for 50, 30, and 22 nm HPs and about 1:2 for 40 nm HP; most HP values met the industry requirement of LWR less than 20% of CD.
- TinOH tin–oxygen photoresist exhibited dual-tone behavior: low electron-beam doses (e.g., 50 µC/cm2) gave positive-tone patterns, while higher doses (e.g., 400 and 1000 µC/cm2) gave negative-tone patterns; under EUV, low dose (e.g., 3.6 mJ/cm2) produced positive tone and higher dose (e.g., 53.5 mJ/cm2) produced negative tone.
- IVB group HfO2 and ZrO2 nanoparticle photoresists showed etch resistance surpassing polymer resists by up to 25 times, enabled processing of films <40 nm, and achieved resolution limits below 20 nm; ZrMAA films were patterned in negative tone with a record-low EUV dose of 4.2 mJ/cm².
Methods
- Design: narrative review of recent advances in inorganic metal-oxide-based photoresists for EUVL, covering zinc-based, tin–oxygen, and IVB group materials.
- Data/sample: published literature and cited experimental studies, including studies on zinc oxo clusters, tin oxo cages, HfO2/ZrO2 nanoparticles, and industry examples; no primary experiments were conducted by the review authors.
- Main analysis: thematic synthesis of photoresist chemistry, synthesis techniques (e.g., ALD, ASD, VPI, MALD, non-aqueous sol–gel), characterization methods (e.g., XPS, XAS, nano-IR, SEM, CD-SEM, TEM, AFM), performance evaluation, applications, and market prospects.
Limitations
- The paper does not state explicit limitations.
- As a review, it reports performance numbers from cited studies rather than generating or independently validating new experimental data.
- The scope is limited to zinc-based, tin–oxygen, and IVB group inorganic photoresists, so findings may not generalize to all metal-oxide or EUV photoresist systems.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures
![Figure 2 (a) Hydrolysis–dehydration chemical reaction for Zn oxo cluster formation (reprinted with permission from ref. [23], 2012, Royal Society of Chemistry). (b) Structure of tin oxo clusters (reprinted with permission from ref. [21], 2014, Elsevier). (c) Photochemical reactions for TinOH subjected to UV in air and N2 [22].](https://figures.cochat.ai/paper-figures/0ecb04ca66c34b7aaa40ca89b9e9237b/recent-advances-in-metal-oxide-based-photoresists-for-euv-lithography-figure-2.jpg)
![Figure 5 (a) Diagram showing the area-specific ALD process. (b) The EUV patterning process flow in combination with the area-selective deposition method: (1) EUV resist spin-coating on substrate, (2) exposure of the pattern via EUV lithography, (3) development and materials applied to (4) patterned EUV resist or (5) substrate on a selective basis [30].](https://figures.cochat.ai/paper-figures/61a65dfd12704a04b2eda5126348348b/recent-advances-in-metal-oxide-based-photoresists-for-euv-lithography-figure-5.jpg)
![Figure 6 (a) Workflow for patterning integrated with VPI: (1) applying resist onto a Si substrate using spin-coating, (2) exposing the pattern using e-beam or EUV lithography, (3) development step, and (4) SIS AlOx infiltration. (b) Workflow for VPI before lithography: (1) applying resist onto the substrate using spin-coating, (2) infiltrating with AlOx, and (3) pattern exposure using e-beam or EUV lithography [30].](https://figures.cochat.ai/paper-figures/a681d6e0c0a844ffb039af08d0c58656/recent-advances-in-metal-oxide-based-photoresists-for-euv-lithography-figure-6.jpg)
![Figure 10 (a) Diagram illustrating a hybrid inorganic/organic nanoparticle featuring a HfO2 core surrounded by an organic ligand shell (reprinted with permission from ref. [68], 1972, Royal Society of Chemistry). (b) Structural representation of ZrMc metal oxo clusters used as photoresists, showing the coordination geometry with polygons, oxygen atoms as red spheres, and C-C bonds as gray bars. (Reprinted with permission from ref. [8], 2002, SPIE).](https://figures.cochat.ai/paper-figures/19101be375f743d4972193cb5f5c9b1a/recent-advances-in-metal-oxide-based-photoresists-for-euv-lithography-figure-10.jpg)
![Figure 11 Architecture of HFO2 and ZrO2 nanoparticle-based photoresists (reprinted with permission from ref. [69], 2014, SPIE).](https://figures.cochat.ai/paper-figures/cf82c97cdef240518e0dde576927cdb8/recent-advances-in-metal-oxide-based-photoresists-for-euv-lithography-figure-11.jpg)
![Figure 1 (a) Lithography technology advancement from 1970 to 2020. (b) DUV and EUV lithography comparison [6]. (c) Photochemical reactions of EUV photoresist (reprinted with permission from ref. [5], 2023, Elsevier). (d) Definitions of line edge roughness and line width roughness (reprinted with permission from ref. [7], 2016, Elsevier). (e) Absorption coefficient of different metal oxide photoresists at EUV as compared to traditional CAR (reprinted with permission from ref. [8], 2002, SPIE).](https://figures.cochat.ai/paper-figures/67260658f6e4494c828910e2d87c1824/recent-advances-in-metal-oxide-based-photoresists-for-euv-lithography-figure-1.jpg)
![Figure 3 Increase in size of HfO2 particle mechanism after UV treatment [27].](https://figures.cochat.ai/paper-figures/aa6704dbef8a410abba7528f72c02216/recent-advances-in-metal-oxide-based-photoresists-for-euv-lithography-figure-3.jpg)
![Figure 4 (a) Atomic absorption of different elements at EUV; (b) Experimental setup for absorption measurement (reprinted with permission from ref. [8], 2002, SPIE).](https://figures.cochat.ai/paper-figures/ce04d5021b9046e9a916604665f163c5/recent-advances-in-metal-oxide-based-photoresists-for-euv-lithography-figure-4.jpg)
![Figure 7 (a) The procedure of the MALD method, which involves the growth of hybrid thin films by sequentially exposing inorganic and organic precursors. (b) The surface reactions in the MALD formation of poly(aluminum ethylene glycol) alucone, utilizing TMA (A) and EG (B) as the inorganic and organic precursors, respectively [30].](https://figures.cochat.ai/paper-figures/e4408453dc314dc3a9d422745288dfdd/recent-advances-in-metal-oxide-based-photoresists-for-euv-lithography-figure-7.jpg)
![Scheme 1 Condensation reactions forming metal–oxygen–metal bonds in non-aqueous sol–gel processes include: alkyl halide elimination (Equation (1)), ether elimination (Equation (2)), ester elimination (Equation (3)), and aldol-like condensation (Equation (4)) [42].](https://figures.cochat.ai/paper-figures/277ff7a4713f488499e91886cd2390f3/recent-advances-in-metal-oxide-based-photoresists-for-euv-lithography-figure-10.jpg)
![Scheme 2 Suggested reaction pathway for creating a C–C bond, resulting in the concurrent production of BaTiO3 nanoparticles and 4-phenyl-2-butanol [42].](https://figures.cochat.ai/paper-figures/55f2b52eca4c40ef91c30af941b4f0c1/recent-advances-in-metal-oxide-based-photoresists-for-euv-lithography-figure-11.jpg)
![Figure 8 Various cluster structures synthesized using Zn2(CO2)4 as the metal unit combined with different organic ligands. (a) The crystal structure of MOF-2, (b) the structure of Zn-BA, (c) the structure of Zn-mTA, (d) 15 nm high-precision line-space (HP LS) structure can be fabricated through photoetching technology by employing Zn-mTA as a photoresist. The atomic color coding in the structures is as follows: carbon is represented in gray, oxygen in red, nitrogen in purple, hydrogen in white, and zinc in blue [60]. (e) The diagram of a ligand exchange reaction resulting in Zn(MA)(TFA) synthesis [61].](https://figures.cochat.ai/paper-figures/47712c0d628244f285a422e2041c8d54/recent-advances-in-metal-oxide-based-photoresists-for-euv-lithography-figure-8.jpg)
![Figure 9 (a) Bond dissociation energies and photolithography results for three organic groups. (b) Correlation between the radical stability of organic groups and the sensitivity of clusters. (c) Phenyltin trichloride is converted into phenylstannic acid, and then dehydrated to synthesize tin clusters. (d) Phenyltin trichloride is hydrolyzed with ammonium hydroxide to form a soluble polymer material (reprinted with permission from ref. [21], 2014, Elsevier).](https://figures.cochat.ai/paper-figures/c86abc533cc54210a75e6f7725c23d03/recent-advances-in-metal-oxide-based-photoresists-for-euv-lithography-figure-9.jpg)
![Figure 12 (a) LWR results were determined using power spectral density (PSD) analysis of SEM images (taken at 2 kV) of the line and space features. (b) The experimental data were fitted to F 1s high-resolution spectra for both unexposed and EUV-exposed Zn(MA)(TFA) resists, revealing variations in elemental ratios of specific components relative to Zn based on EUV dose. (c) FTIR spectra of Zn(MA)(TFA) resist films were analyzed before and after EUV exposure, including a schematic of the exposed sample showing regions subjected to different EUV doses and the changes in peak areas related to MA and TFA ligands as a function of dose compared to the unexposed region [59].](https://figures.cochat.ai/paper-figures/e072d13a32434b5bae4ee5af04d8efd8/recent-advances-in-metal-oxide-based-photoresists-for-euv-lithography-figure-12.jpg)
![Figure 13 (a) SEM and AFM images of tin oxo cage thin films patterned with 3.6 mJ/cm2 and 53.5 mJ/cm2 EUV doses, along with their corresponding cross-sectional profiles. (b) The spectra of TinOH thin layers with various EUV exposures and post-exposure baking, TGA of TinOH powder, highlighting weight changes and the loss of water, butene, and butane with temperature [89].](https://figures.cochat.ai/paper-figures/b27ab46800f14b84876c611da73b1f23/recent-advances-in-metal-oxide-based-photoresists-for-euv-lithography-figure-13.jpg)
![Figure 14 SEM images showing patterns of Zr clusters with varying line spacings (1:5 ratio): (a) Lines composed of Zr oxo clusters with a 15 nm pattern width; (b) Lines of Zr oxo clusters with a 16 nm pattern width; (c) Lines formed from Zr6O4 clusters, each 15 nm wide; (d) Zr6O4 cluster lines, each 16 nm in width (reprinted with permission from ref. [76], 2022, John Wiley and Sons).](https://figures.cochat.ai/paper-figures/beeb72fee3244fa4a75df3aec4fe96a5/recent-advances-in-metal-oxide-based-photoresists-for-euv-lithography-figure-14.jpg)
![Figure 15 SEM images of Zn-mTA cluster line and space dense patterns fabricated via EUV exposure: (a) 16 nm at a dose of 45 mJ/cm2, (b) 15 nm at a dose of 47 mJ/cm2, (c) 14 nm at a dose of 36 mJ/cm2, and (d) 13 nm at a dose of 35 mJ/cm2 [60].](https://figures.cochat.ai/paper-figures/f6d09c8af1c74a478ba4599870a2ed12/recent-advances-in-metal-oxide-based-photoresists-for-euv-lithography-figure-15.jpg)
![Figure 16 (a) Optical density (EUV) mentioned in periodic table. (b) Tin clusters were examined using lithographic techniques to determine their relative sensitivity (reprinted with permission from ref. [92], 2014, SPIE).](https://figures.cochat.ai/paper-figures/57449492fc024c3a9d713116b5c43e82/recent-advances-in-metal-oxide-based-photoresists-for-euv-lithography-figure-16.jpg)
![Figure 17 Hysteresis curve comparison of Si-doped and Hf-Zr-based sensors with better area increase on the substrate [94].](https://figures.cochat.ai/paper-figures/f2577dff3d624cbfa0ef2f79deb3e998/recent-advances-in-metal-oxide-based-photoresists-for-euv-lithography-figure-17.jpg)
Verification
Claims the paper makes
62 Valid · 10 Not valid · 121 Not checked · 52 Own results and interpretations
At least one cited source doesn’t support this claim or points to a different paper, and none confirmed it — see the verdicts below.
In the paper
“The patterns exhibited low LER, with roughness values below 3 nm, critical for ensuring the accuracy and reliability of semiconductor components.”
§ Recent Advances in Metal-Oxide-Based Photoresists for EUV Lithography > 5. Performance Evaluation of Metal-Oxide-Based Photoresists > 5.3. Analysis of IV B Group Inorganic-Based Photoresists
What the sources say
- Disputedcites [24] Trikeriotis, 2012, Nanoparticle Photoresists from HfO2 and ZrO2 for EUV Patterning, J. Photopolym. Sci. Technol. sourceExperimental — accuracy not yet measured
The paper describes the patterns as having low LER (p. 1), but its measured values contradict the claimed threshold. The preparation section (p. 3) reports LER values of 5.9 nm and 3.8 nm for the two patterns shown, both above 3 nm. (LLM, conf=0.90)
Checked by a reasoning model — may be wrong.
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Disputed
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Research by Fallica et al. [8] confirmed that metal oxides absorb EUV light more efficiently than organic polymers.”
§ Recent Advances in Metal-Oxide-Based Photoresists for EUV Lithography > 1. Introduction
What the sources say
- Partly supportedcites [8] Fallica, 2018, Absorption coefficient of metal-containing photoresists in the extreme ultraviolet, J. Micro/Nanolithogr. MEMS MOEMS sourceExperimental — accuracy not yet measured
The Abstract reports that tin-containing and hafnium-containing resists absorbed more EUV light than conventional organic photoresists. But it also reports that zirconium oxoclusters had comparable absorptivity, so the paper does not confirm the claim for metal oxides generally. (LLM, conf=0.90)
boostedstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“IVB group metal oxides, including hafnium and zirconium, enhance etch resistance and resolution through reduced organic content and careful ligand selection.”
§ Recent Advances in Metal-Oxide-Based Photoresists for EUV Lithography > 2. Metal-Oxide-Based Photoresist Chemistry
What the sources say
- Partly supportedcites [18] Luo, 2020, Review of recent advances in inorganic photoresists, RSC Adv. sourceExperimental — accuracy not yet measured
The IVB-group photoresists section says hafnium oxide improves etch resistance and that reducing organic content can improve it further. It links small, uniformly sized oxide particles to better resolution. The Conclusions and outlook section proposes ligand design as a way to optimize performance, including resolution, but does not establish that careful ligand selection has already enhanced resolution. (LLM, conf=0.82)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Zinc-based inorganic photoresists, incorporating zinc oxide as the photoactive component, offer enhanced chemical reactivity upon light exposure, crucial for high-resolution patterning.”
§ Recent Advances in Metal-Oxide-Based Photoresists for EUV Lithography > 2. Metal-Oxide-Based Photoresist Chemistry
What the sources say
- Partly supportedcites [18] Luo, 2020, Review of recent advances in inorganic photoresists, RSC Adv. sourceExperimental — accuracy not yet measured
The Zinc-based inorganic photoresist section says ZnO can be used as a photoresist and describes light-induced ligand detachment and aggregation in zinc oxo clusters. It also reports high-resolution patterning with a zinc-cluster resist, but does not establish that ZnO provides enhanced photochemical reactivity or that such enhancement is crucial to the resolution achieved. Page numbers were not supplied for these passages. (LLM, conf=0.82)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Nevertheless, when ZrO2 is coordinated with organic ligands, its EUV absorptivity approximates that of organic photoresists [18].”
§ Recent Advances in Metal-Oxide-Based Photoresists for EUV Lithography > 3. Metal-Oxide-Based Photoresist Synthesis Techniques > 3.2. Novel Inorganic Metal-Oxide-Based Photoresists and Synthesis Processes
What the sources say
- Partly supportedcites [18] Luo, 2020, Review of recent advances in inorganic photoresists, RSC Adv. sourceExperimental — accuracy not yet measured
The Inorganic photoresists section (page unavailable) says ZrOx has approximately the same EUV absorptivity as organic photoresist. The IVB group section describes zirconium oxide photoresists with organic ligands, but does not establish that the absorptivity comparison applies specifically to ligand-coordinated ZrO2. (LLM, conf=0.84)
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
96 more claims · 29 with their cited sources checked
Create a free account to see all 245 claims and to verify the 11 references still open.
- It may state two separate claims as one. 116
- Probably not a substantial claim. 43
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Recent Advances in Metal-Oxide-Based Photoresists for EUV Lithography > 3. Metal-Oxide-Based Photoresist Synthesis Techniques > 3.2. Novel Inorganic Metal-Oxide-Based Photoresists and Synthesis Processes
“(Reprinted with permission from ref. [8], 2002, SPIE).”
§ Recent Advances in Metal-Oxide-Based Photoresists for EUV Lithography > References
“8. Fallica R. Haitjema J. Wu L. Castellanos S. Brouwer A.M. Ekinci Y. Absorption coefficient of metal-containing photoresists in the extreme ultraviolet J. Micro/Nanolithogr. MEMS MOEMS 2018 17 23505”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Recent Advances in Metal-Oxide-Based Photoresists for EUV Lithography > 2. Metal-Oxide-Based Photoresist Chemistry > 2.2. Tin–Oxygen Inorganic Photoresist Mechanism
“The group of Zhang et al. [22] have also studied the photochemical reactions occurring in tin oxo cage clusters.”
§ Recent Advances in Metal-Oxide-Based Photoresists for EUV Lithography > References
“22. Yu Z. Jarich H. Xiaomeng L. Fredrik J. Andreas L. Sonia C. Niklas O. Albert M.B. Photochemical conversion of tin-oxo cage compounds studied using hard x-ray photoelectron spectroscopy”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Recent Advances in Metal-Oxide-Based Photoresists for EUV Lithography > 3. Metal-Oxide-Based Photoresist Synthesis Techniques > 3.2. Novel Inorganic Metal-Oxide-Based Photoresists and Synthesis Processes
“Figure 10 (a) Diagram illustrating a hybrid inorganic/organic nanoparticle featuring a HfO2 core surrounded by an organic ligand shell (reprinted with permission from ref. [68], 1972, Royal Society of Chemistry).”
§ Recent Advances in Metal-Oxide-Based Photoresists for EUV Lithography > References
“68. Li L. Liu X. Pal S. Wang S. Ober C.K. Giannelis E.P. Extreme ultraviolet resist materials for sub-7 nm patterning Chem. Soc. Rev. 2017 46 4855 4866”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Recent Advances in Metal-Oxide-Based Photoresists for EUV Lithography > 2. Metal-Oxide-Based Photoresist Chemistry > 2.2. Tin–Oxygen Inorganic Photoresist Mechanism
“(a) Hydrolysis–dehydration chemical reaction for Zn oxo cluster formation (reprinted with permission from ref. [23], 2012, Royal Society of Chemistry).”
§ Recent Advances in Metal-Oxide-Based Photoresists for EUV Lithography > References
“23. Yeh C.-C. Liu H.-C. Heni W. Berling D. Zan H.-W. Soppera O. Chemical and structural investigation of zinc-oxo cluster photoresists for DUV lithography J. Mater. Chem. C 2017 5 2611 2619”
Citations
Cites
Nonaqueous sol–gel routes to metal oxide nanoparticles
Niederberger, M. (2007) · Accounts of Chemical Research · doi:10.1021/ar600035e · Cited by 761 · cited 6×
“Given these features, the main advantages of solvent-controlled approaches include [42]: Improved Product Purity: The absence of surfactants eliminates issues related to nanoparticle surface accessibility, crucial for applications in catalysis and sensing, as well as reduces potential toxicity…”
BackgroundMethodInfluentialOne‐Nanometer‐Scale Size‐Controlled Synthesis of Monodisperse Magnetic Iron Oxide Nanoparticles
Park, J., Lee, E., Hwang, N., Kang, M., Kim, S. C., Hwang, Y., Park, J., Noh, H., Kim, J., Park, J., et al. (2005) · Angewandte Chemie International Edition · doi:10.1002/anie.200461665 · Cited by 652 · cited 2×
“…Iron Oxide Nanoparticles: Achieving sizes from 6–13 nm in precise one-nanometer steps by manipulating surfactant concentrations and reaction conditions [51]. o Ferrite Nanoparticles (MFe 2 O 4 ): Shape control (cube-like and polyhedron-shaped) was achieved through non-hydrolytic…”
BackgroundMethodde Mello Donegá, C., Liljeroth, P., & Vanmaekelbergh, D. (2005) · Small · doi:10.1002/smll.200500239 · Cited by 511 · cited 1×
“This approach utilizes the hot-injection method where a precursor solution is injected into a hot solvent containing surfactants [50].”
MethodChemCalc: A building block for tomorrow’s chemical infrastructure
Patiny, L., & Borel, A. (2013) · Journal of Chemical Information and Modeling · doi:10.1021/ci300563h · Cited by 425 · cited 2×
“These ligands enhance solubility and contribute to increased EUV photon absorption due to the presence of fluorine [20].”
BackgroundMultigram Scale Synthesis and Characterization of Monodisperse Tetragonal Zirconia Nanocrystals
Joo, J., Yu, T., Kim, Y. W., Park, H. M., Wu, F., Zhang, J. Z., & Hyeon, T. (2003) · Journal of the American Chemical Society · doi:10.1021/ja034258b · Cited by 412 · cited 1×
“TiO 2 , ZrO 2 , and HfO 2 exhibits the ability to create diverse nanostructures with controlled dimensions and distinctive morphologies using surfactant-mediated synthesis [46,54,55].”
BackgroundSynthesis of TiO2 Nanocrystals by Nonhydrolytic Solution-Based Reactions
Trentler, T. J., Denler, T. E., Bertone, J. F., Agrawal, A., & Colvin, V. L. (1999) · Journal of the American Chemical Society · doi:10.1021/ja983361b · Cited by 382 · cited 1×
“This process is exemplified in the synthesis of anatase nanocrystals from titanium isopropoxide and titanium chloride [43] ((1) in Scheme 1).”
Shape-Controlled Synthesis and Shape-Induced Texture of MnFe 2 O 4 Nanoparticles
Zeng, H., Rice, P. M., Wang, S. X., & Sun, S. (2004) · Journal of the American Chemical Society · doi:10.1021/ja045911d · Cited by 369
Extreme ultraviolet resist materials for sub-7 nm patterning
Li, L., Liu, X., Pal, S., Wang, S., Ober, C. K., & Giannelis, E. P. (2017) · Chemical Society Reviews · doi:10.1039/c7cs00080d · Cited by 345
Narayanaswamy, A., Xu, H., Pradhan, N., Kim, M., & Peng, X. (2006) · Journal of the American Chemical Society · doi:10.1021/ja0627601 · Cited by 307 · cited 1×
“Ester elimination takes place between metal alkoxides and carboxylates, a method applied in the synthesis of zinc oxide [45], titania [46], and indium oxide [47] ((3) in Scheme 1).”
MethodNiederberger, M., Garnweitner, G., Pinna, N., & Antonietti, M. (2004) · Journal of the American Chemical Society · doi:10.1021/ja0494959 · Cited by 284 · cited 1×
“Subsequently, there is a transfer of hydroxyl groups and condensation leading to the formation of metal oxide [49] (Scheme 2). metal oxide [49] (Scheme 2) Scheme 2.”
Background
Cited by
Basu, P., Verma, J., Abhinav, V., Ratnesh, R. K., Singla, Y. K., & Kumar, V. (2025) · International Journal of Molecular Sciences · doi:10.3390/ijms26073027 · Cited by 98
Advances in metal-based photoresist materials for EUV lithography and lithographic mechanisms
Wang, Y., Yu, H., Wang, L., Zhang, Y., Zhu, Z., Zhang, Y., Lu, Y., & Ouyang, C. (2025) · Journal of Materials Chemistry A · doi:10.1039/d5ta04194e · Cited by 17
Liu, Z., Chen, J., Yu, T., Zeng, Y. P., Guo, X., Wang, S., Hu, R., Vockenhuber, M., Tian, P., Kazazis, D., et al. (2025) · ACS Applied Electronic Materials · doi:10.1021/acsaelm.5c00273 · Cited by 9
The Evolution of Lithography: From Resolution Scaling to Manufacturing Constraints
Chae, H., Park, H., & Kang, D. J. (2026) · Micromachines · doi:10.3390/mi17020261 · Cited by 13
Li, H., An, H., Chen, J., Yu, T., Zeng, Y. P., Wang, S., Guo, X., Hu, R., Zhao, J., Wu, Y., et al. (2025) · Chinese Journal of Chemistry · doi:10.1002/cjoc.70379 · Cited by 6
Metadata
- Authors
- Hasan, M. W., Deeb, L., Kumaniaev, S., Wei, C., & Wang, K.
- Affiliations
- University of South-Eastern Norway (NO)
- Corresponding author
- Wang, Kaiying
- ORCID
- Wang, Kaiying
- Venue
- Micromachines
- Publisher
- MDPI AG
- Published
- 2024-08-31
- Volume
- 15
- Issue
- 9
- Pages
- 1122
- ISSN
- 2072-666X (ISSN-L)
- PMC
- PMC11433861
- OpenAlex
- W4402137876
- Cited by
- 35
- References
- 101
- Citations by year
- 2026: 21 · 2025: 14
- FWCI
- 0.72
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Micromachines (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Photolithography Techniques
- Physical Sciences › Materials Science › Surfaces, Coatings and Films › Nanofabrication and Lithography Techniques
- Physical Sciences › Chemistry › Organic Chemistry › Photopolymerization techniques and applications
- Keywords
- EUV lithography, zinc oxide nanoparticles, SnO2 nanoparticles, photochemical reactions, ligands, crosslinking, film density, solubility, photon absorption, semiconductor patterning, pyroelectric infrared sensor, 3D printing
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Recent Advances in Metal-Oxide-Based Photoresists for EUV Lithography. https://app.cochat.ai/papers/10.3390/mi15091122
- The paper
- Hasan, M. W., Deeb, L., Kumaniaev, S., Wei, C., & Wang, K. (2024). Recent Advances in Metal-Oxide-Based Photoresists for EUV Lithography. Micromachines. https://doi.org/10.3390/mi15091122
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.