Ionic Liquids as Solvents for Rhodium and Platinum Catalysts Used in Hydrosilylation Reaction
Open accessThe DOI matches its Crossref record; 28 of the 28 references it cites were found in a registry or an index; none of the 20 sources its claims cite is checked for support yet.
Abstract
A group of imidazolium and pyridinium based ionic liquids has been synthetized, and their ability to dissolve and activate the catalysts used in hydrosilylation reaction of 1-octane and 1,1,1,3,5,5,5-heptamethyltrisiloxane was investigated. An organometallic catalyst as well as inorganic complexes of platinum and rhodium dissolved in ionic liquids were used, forming liquid solutions not miscible with the substrates or with the products of the reaction. The results show that application of such a simple biphasic catalytic system enables reuse of ionic liquid phase with catalysts in multiple reaction cycles reducing the costs and decreasing the amount of catalyst needed per mole of product.
Overview
CoChat Summary
TL;DR
This paper tests ionic liquids (ILs) as biphasic solvents for rhodium and platinum catalysts in the hydrosilylation of 1-octene with 1,1,1,3,5,5,5-heptamethyltrisiloxane (HMTS). The main takeaway is that some IL/catalyst pairs can be reused for up to five cycles with yields around or above 80%, while ILs bearing unsaturated side chains generally perform poorly.
Key findings
- The study screened 42 possible combinations of ILs and catalysts, and found that three out of seven tested IL systems were useful in five subsequent cycles with yields maintained at around 80%.
- The best-performing system was [P44414][NTf2] (1), which gave yields close to 100% throughout five reaction cycles for catalysts such as [RhCl(PPh3)3], Pt(PPh3)2Cl2, and Karstedt catalyst; for some of these, yield stayed at 100% up to the fourth cycle.
- For [BMMIM][NTf2] (3), the paper reports yields close to 100% with Pt(PPh2)2Cl2 and Pt(PPh3)3 (decreasing to 60% after the last cycle), and a rhodium catalyst that maintained 100% yield up to the fourth cycle, before dropping from 99% to 5%.
- The least effective IL systems were [BuPy][NTf2] (2), [diAllMIM][NTf2] (6), and [AlldiMIM][NTf2] (7), which gave yields in almost every case of only 0–30%; ILs with unsaturated side chains were said to cause near-immediate catalyst deactivation.
Methods
- The authors synthesized and/or used seven IL systems and tested them with six catalysts: platinum and rhodium complexes including K2PtCl4, K2PtCl6, Pt(PPh3)2Cl2, Pt(PPh3)4, [RhCl(PPh3)3], and Karstedt catalyst.
- Catalyst activity was measured in small-scale 4 mL glass reactors using a biphasic system: IL formed the bottom phase, while reactants/products formed the upper phase; the reaction was run at 110 °C for 1 h per cycle.
- Reaction conversion and yield were monitored by gas chromatography, and the IL/catalyst phase was reused for subsequent cycles after phase separation.
Limitations
- The paper states that ICP quantification of catalysts in ILs was not possible, because the catalyst amounts were close to the ICP detection limits.
- The study is limited to a model hydrosilylation system (1-octene + HMTS), so broader applicability to other substrates is not directly tested in the text.
- Evident from the design: the work is a screening study on small-scale batch reactions, so it does not establish long-term process performance beyond the reported recycling cycles.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures
![Figure 1 Schematic representation of ionic liquids used as solvent for catalyst in hydrosilylation reaction (1–7). All ILs have the same anion: bis(trifluoromethylsulfonyl)imide—[NTf2]− (highlighted by a frame).](https://figures.cochat.ai/paper-figures/0129ec6e007e490fa62a0ac8c9fa077f/ionic-liquids-as-solvents-for-rhodium-and-platinum-catalysts-used-in-figure-1.jpg)

![Figure 3 The yields of hydrosilylation reaction carried out in [P44414][NTf2] (1) (tributyltetradecylphosphonium bis(trifluoromethylsulfonyl)imide) in subsequent cycles. Colors refer to different catalysts used in hydrosilylation reaction.](https://figures.cochat.ai/paper-figures/dc8cd01f6d384adbadee52e100895c76/ionic-liquids-as-solvents-for-rhodium-and-platinum-catalysts-used-in-figure-3.jpg)
![Figure 4 The yields of hydrosilylation reaction carried out in [BMMIM][NTf2] (3) (1-butyl-2,3-dimethylimidazolium bis(trifluoromethylsulfonyl)imide) in subsequent cycles. Colors refer to different catalysts used in hydrosilylation reaction.](https://figures.cochat.ai/paper-figures/7f881556ebf64e818ff9236cd22c29c5/ionic-liquids-as-solvents-for-rhodium-and-platinum-catalysts-used-in-figure-4.jpg)
 (4) (triethylsulfonium bis(trifluoromethylsulfonyl)imide) in subsequent cycles. Colors refer to different catalysts used in hydrosilylation reaction.](https://figures.cochat.ai/paper-figures/60e9e9aef74d44fdae51522a9002b8d6/ionic-liquids-as-solvents-for-rhodium-and-platinum-catalysts-used-in-figure-5.jpg)
Verification
Claims the paper makes
0 Valid · 0 Not valid · 10 Not checked · 36 Own results and interpretations
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“An organometallic catalyst as well as inorganic complexes of platinum and rhodium dissolved in ionic liquids were used, forming liquid solutions not miscible with the substrates or with the products of the reaction.”
- Also stated in: § 3. Discussion · boosted
“The use of IL systems, as proposed in the described studies, guarantees recovery of the IL solvent due to its property, insolubility in substrates nor products of the reaction.”
§ Ionic Liquids as Solvents for Rhodium and Platinum Catalysts Used in Hydrosilylation Reaction > Abstract
boosted- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Also stated in: § 3. Discussion · boosted
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“In some cases, the IL phase was used up to more than five cycles before catalytic properties were lost and a new IL phase had to be prepared.”
§ Ionic Liquids as Solvents for Rhodium and Platinum Catalysts Used in Hydrosilylation Reaction > 1. Introduction Recently, there has been major interest in more “green” and environmentally-friendly approaches to industrial processes and technologies. Very helpful in obtaining such goals can be compounds known as ionic liquids (ILs) [1]. The most commonly used definition of ILs refers to their melting point lying below 100 °C, which means, that they are salts melted at room temperature (or below 100 °C) composed of organic or inorganic cations and anions. From these ionic structures emerge interesting properties such as: low viscosity; low vapor pressure [2]; and good dissolution in many inorganic, organic and polymeric compounds [3]. Huge interest in IL chemistry, and intensification of research on ILs in the last decade is reflected in a growing number of publications referring to IL properties, synthesis and applications [1,4,5,6] starting with their solvent properties in organic synthesis [7] as well as use in energy storage materials [8], medicine [9], catalysis [10], separation science [11] or crystallography [12] to name only a few. However, the most useful feature of ILs is their tunability of properties possible through chemical modifications of cations or anions and hence adjustment of the intermolecular and interionic interactions [12]. The combinations of cations and anions composing ILs and applications for them are growing on a daily basis. The cations are generally bulky, asymmetric ammonium or phosphonium salts, or heteroaromatics, with low symmetry, weak intermolecular interactions and low charge densities. Typically, the anions are described as non-coordinating, inorganic ions and include [PF6]−, [BF4]−, [CF3SO3]− or [(CF3SO2)2N]−, although, more recently, organic anions (e.g., [RCO2]−) have also been introduced [13]. The physical and chemical properties of the ionic liquid, including their melting points, are dependent on both the nature of the cation and the anion. A schematic representation of ILs used in our study is presented in Figure 1. Solvent effect on reactions is one of the most interesting issues related to research on ILs [14]. The ILs have been used successfully as a media for many reactions [15], for example carbon–carbon bond forming reactions (Knoevenagel, Michael Aldol, Biginelli, Heck reactions), substitution, elimination, addition (i.e., nucleophilic, electrophilic aromatic substitution, esterification, Diels–Alder) acid catalyzed reactions and transition-metal catalyzed reactions i.e., hydrogenation, oxidation or carbonylation. There are also many possibilities of IL application in catalysis [16] i.e., as the catalyst itself, as a co-catalyst, as a catalyst activator, as the source of a new ligand for a catalytic metal center, or as a solvent for the reaction. There are many examples of catalytic processes involving ILs and one of them is the hydrosilylation reaction in which ILs immobilize platinum [17] or rhodium [18] catalysts used during biphasic reactions in batch. There have been several comprehensive papers regarding hydrosilylation reaction carried in the presence of ILs [19,20,21], but articles usually focus on a narrow scope of catalyst/IL systems, usually investigating in-depth one particular catalyst. As it is reported by Hoffman et al. [22], most suitable for hydrosilylation reaction are salts with the [NTf2]− anion. Thus, during our study, we have focused primarily on the investigation of various catalysts and their performance in different ILs, specifically containing [NTf2]− anion, thus being able to investigate the influence of chemical modification of the cation on the catalyst activity. Utilization of a biphasic system allows for reducing the amount of catalyst used during the process by reuse of IL-phase in subsequent cycles. This simple method results also in decreased contamination of product with catalyst. This aspect is especially important since hydrosilylation reaction products are very commonly used in the cosmetic and food industry [23]. Due to their unique properties, organosilicon compounds are widely used and have become indispensable in our daily life. Through their dual reactivity, organosilanes serve as bridges between inorganic or organic substrates (such as minerals, fillers, metals and cellulose) and organic/polymeric matrices (such as rubber, thermoplastics or thermosets) and, hence, can dramatically improve adhesion between them [24]. Organosilicons consist mainly of Si–C bonds that do not exist naturally and have to be synthesized via hydrosilylation reaction [25], one of the most convenient and widely used methods of forming Si–C bonds. It involves the addition of the Si–H bond in hydrosilane across an unsaturated hydrocarbon such as an alkene or alkyne (Figure 2). For such a reaction, a transition-metal catalyst is required [26]. Among many transition-metal catalysts reported to date, platinum catalysts such as Speier’s catalyst and Karstedt’s catalyst are known to be very effective and are often used commercially [27]. However, we know that the use of precious metals in catalysis is not always desired and the used amount should be as little as possible. The relatively high cost, environmental concerns, and uncertainty of the long-term supply of precious metals have inspired the search for equivalent or superior catalysts, or improved synthetic methods that allow for minimizing the amount of used catalysts. Hence, in our study, we have proposed a more economic approach to catalytical hydrosilylation reaction with the use of ILs. This very simple concept involves two immiscible liquids creating a biphasic system, where one phase constitutes IL with a dissolved catalyst, and another is composed of substrates and after time products. This approach allows for separation of both phases and reuse of the IL phase with catalysts. In some cases, the IL phase was used up to more than five cycles before catalytic properties were lost and a new IL phase had to be prepared. This approach in contrast to the traditional approach allows saving money spent on catalysts and enables construction of closed cycle reaction systems. In order to isolate best pairs of IL/catalysts for hydrosilylation reactions, we have investigated six catalysts and seven ILs.
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“In our opinion, three out of seven tested IL systems have proven to be useful in five subsequent cycles with yields maintained at a level of around 80%.”
§ Ionic Liquids as Solvents for Rhodium and Platinum Catalysts Used in Hydrosilylation Reaction > 2. Results
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“In the case of K2PtCl4, K2PtCl6 and Karstedt catalysts, the yields after the second cycle have reached unacceptable values.”
§ Ionic Liquids as Solvents for Rhodium and Platinum Catalysts Used in Hydrosilylation Reaction > 2. Results
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“in other two examples with salts previously investigated by our group, ([BMMIM][NTf2] (3) and [S222][NTf2]) (4), high yields of conversion were observed even after a third cycle.”
§ Ionic Liquids as Solvents for Rhodium and Platinum Catalysts Used in Hydrosilylation Reaction > 3. Discussion
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
22 more claims
Create a free account to see all 46 claims and to verify the 20 references still open.
- It may state two separate claims as one. 16
- The quote only partly states this claim. 1
- Probably not a substantial claim. 4
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The check wasn’t confident either way, so it gives no verdict — never disputed.
In the citing paper
“The authors are sorry to report that the yield of the hydrosilylation reaction in [P44414][NTf2] (1) IL with [RhCl(PPh3)3] was replaced with the yield reported for [P44414][NTf2] (1) IL with K2PtCl4 in their published paper [1].”
From Correction: Zielinski, W., et al. Ionic Liquids as Solvents for Rhodium and Platinum Catalysts Used in Hydrosilylation Reaction. Molecules 2016, 21, 1115 (2017) · cites this paper as [1]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Ionic Liquids as Solvents for Rhodium and Platinum Catalysts Used in Hydrosilylation Reaction > 2. Results
“This IL, when used with Pt(PPh2)2Cl2 and Pt(PPh3)3 catalysts, showed best yields close to 100% (decreased to 60% after last reaction cycle) and around 85%, respectively.”
§ Ionic Liquids as Solvents for Rhodium and Platinum Catalysts Used in Hydrosilylation Reaction > 4. Materials and Methods
“bis(triphenylphosphine)platinum chloride, Pt(PPh3)2Cl2 (98%, Sigma Aldrich),”
Citations
Cites
Room-Temperature Ionic Liquids: Solvents for Synthesis and Catalysis. 2
Hallett, J. P., & Welton, T. (2011) · Chemical Reviews · doi:10.1021/cr1003248 · Cited by 12,578
Solvents and Solvent Effects in Organic Chemistry
Reichardt, C. (2002) · Wiley eBooks · doi:10.1002/3527601791 · Cited by 5,789 · cited 1×
“Solvent effect on reactions is one of the most interesting issues related to research on ILs [14].”
BackgroundIonic Liquids—New “Solutions” for Transition Metal Catalysis
Wasserscheid, P., & Keim, W. (2000) · Angewandte Chemie · doi:10.1002/1521-3773(20001103)39:21<3772::aid-anie3772>3.0.co;2-5 · Cited by 5,720 · cited 1×
“It is also known that ILs can serve as catalysts, catalysts immobilizers or initiators in many chemical processes [29].”
BackgroundIonic Liquid (Molten Salt) Phase Organometallic Catalysis
Dupont, J., de Souza, R. F., & Suarez, P. A. Z. (2002) · Chemical Reviews · doi:10.1021/cr010338r · Cited by 3,752
Huddleston, J. G., Visser, A. E., Reichert, W. M., Willauer, H. D., Broker, G. A., & Rogers, R. D. (2001) · Green Chemistry · doi:10.1039/b103275p · Cited by 3,712
(2007) · Wiley eBooks · doi:10.1002/9783527621194 · Cited by 2,768
Energy applications of ionic liquids
MacFarlane, D. R., Tachikawa, N., Forsyth, M., Pringle, J. M., Howlett, P. C., Elliott, G. D., Davis, J. H., Watanabe, M., Simon, P., & Angell, C. A. (2014) · Energy Environ. Sci. · doi:10.1039/c3ee42099j · Cited by 1,745 · cited 1×
“Huge interest in IL chemistry, and intensification of research on ILs in the last decade is reflected in a growing number of publications referring to IL properties, synthesis and applications [1,4–6] starting with their solvent properties in organic synthesis [7] as well as use in energy storage materials [8], medici…”
BackgroundWelton, T. (2004) · Coordination Chemistry Reviews · doi:10.1016/j.ccr.2004.04.015 · Cited by 1,609
Ionic liquids: solvent properties and organic reactivity
Chiappe, C., & Pieraccini, D. (2005) · Journal of Physical Organic Chemistry · doi:10.1002/poc.863 · Cited by 1,169 · cited 1×
“Huge interest in IL chemistry, and intensification of research on ILs in the last decade is reflected in a growing number of publications referring to IL properties, synthesis and applications [1,4–6] starting with their solvent properties in organic synthesis [7] as well as use in energy storage materials [8], medici…”
BackgroundIonic liquids: applications in catalysis
Zhao, D., Wu, M., Kou, Y., & Min, E. (2002) · Catalysis Today · doi:10.1016/s0920-5861(01)00541-7 · Cited by 1,049
Visser, A. E., Swatloski, R. P., Reichert, W. M., Griffin, S. T., & Rogers, R. D. (2000) · Industrial & Engineering Chemistry Research · doi:10.1021/ie000426m · Cited by 640 · cited 1×
“Huge interest in IL chemistry, and intensification of research on ILs in the last decade is reflected in a growing number of publications referring to IL properties, synthesis and applications [1,4–6] starting with their solvent properties in organic synthesis [7] as well as use in energy storage materials [8], medici…”
BackgroundProtic Ionic Liquids: Preparation, Characterization, and Proton Free Energy Level Representation
Belieres, J.-P., & Angell, C. A. (2007) · The Journal of Physical Chemistry B · doi:10.1021/jp067589u · Cited by 545 · cited 1×
“, [RCO2]) have also been introduced [13].”
Ionic liquids for energy, materials, and medicine
Smiglak, M., Pringle, J. M., Lu, X., Han, L., Zhang, S., Gao, H., MacFarlane, D. R., & Rogers, R. D. (2014) · Chem. Commun. · doi:10.1039/c4cc02021a · Cited by 509 · cited 1×
“Huge interest in IL chemistry, and intensification of research on ILs in the last decade is reflected in a growing number of publications referring to IL properties, synthesis and applications [1,4–6] starting with their solvent properties in organic synthesis [7] as well as use in energy storage materials [8], medici…”
BackgroundMarciniec, B. (2005) · Coordination Chemistry Reviews · doi:10.1016/j.ccr.2005.02.025 · Cited by 469 · cited 1×
“For such a reaction, a transition-metal catalyst is required [26].”
BackgroundReichert, W. M., Holbrey, J. D., Vigour, K. B., Morgan, T. D., Broker, G. A., & Rogers, R. D. (2006) · Chem. Commun. · doi:10.1039/b608496f · Cited by 172 · cited 1×
“Very helpful in obtaining such goals can be compounds known as ionic liquids (ILs) [1].”
BackgroundOrganic Synthesis in Ionic Liquids: The Stille Coupling
Handy, S. T., & Zhang, X. (2001) · Organic Letters · doi:10.1021/ol0068849 · Cited by 168 · cited 1×
“There are more than 100 examples of utilization of ILs in different types of organic reactions [28].”
BackgroundApplications of Ionic Liquids in Polymer Science and Technology
Mecerreyes, D. (2015) · Springer eBooks · doi:10.1007/978-3-662-44903-5 · Cited by 113 · cited 1×
“There are also many possibilities of IL application in catalysis [16] i.”
BackgroundBiphasic Hydrosilylation in Ionic Liquids: A Process Set for Industrial Implementation
Geldbach, T. J., Zhao, D., Castillo, N. C., Laurenczy, G., Weyershausen, B., & Dyson, P. J. (2006) · Journal of the American Chemical Society · doi:10.1021/ja0612293 · Cited by 85 · cited 1×
“Imidazolium and pyridinium based ILs have been selected as a most suitable group of ILs for investigation in hydrosilylation reaction due to a few major factors: (i) proved good solubility of many catalysts in ILs containing these cations; (ii) high chemical stability of imidazolium and pyridinium IL systems; (iii) pr…”
BackgroundSolubility of neutral and charged polymers in ionic liquids studied by laser light scattering
Chen, Y., Zhang, Y., Ke, F., Zhou, J., Wang, H., & Liang, D. (2010) · Polymer · doi:10.1016/j.polymer.2010.11.034 · Cited by 65 · cited 1×
“From these ionic structures emerge interesting properties such as: low viscosity; low vapor pressure [2]; and good dissolution in many inorganic, organic and polymeric compounds [3].”
BackgroundUse of ionic liquids for biocatalytic synthesis of sugar derivatives
Galonde, N., Nott, K., Debuigne, A., Deleu, M., Jérôme, C., Paquot, M., & Wathelet, J. (2012) · Journal of Chemical Technology & Biotechnology · doi:10.1002/jctb.3745 · Cited by 53 · cited 2×
“aspect is especially important since hydrosilylation reaction products are very commonly used in the cosmetic and food industry [23].”
BackgroundHofmann, N., Bauer, A., Frey, T., Auer, M., Stanjek, V., Schulz, P. S., Taccardi, N., & Wasserscheid, P. (2008) · Advanced Synthesis & Catalysis · doi:10.1002/adsc.200800438 · Cited by 47 · cited 4×
“[22], most suitable for hydrosilylation reaction are salts with the [NTf2]− anion.”
BackgroundInfluentialHydrosilylation of functionalised olefins catalysed by rhodium siloxide complexes in ionic liquids
Maciejewski, H., Szubert, K., Marciniec, B., & Pernak, J. (2009) · Green Chemistry · doi:10.1039/b819310j · Cited by 46 · cited 2×
“There are many examples of catalytic processes involving ILs and one of them is the hydrosilylation reaction in which ILs immobilize la num [17] or rhod um [18] catalysts used during biphasic reactions in batch.”
BackgroundSelf-citationSilicone waxes—synthesis via hydrosilylation in homo- and heterogeneous systems
Maciejewski, H., Wawrzyńczak, A., Dutkiewicz, M., & Fiedorow, R. M. J. (2006) · Journal of Molecular Catalysis A Chemical · doi:10.1016/j.molcata.2006.04.039 · Cited by 44 · cited 2×
“There are many examples of catalytic processes involving ILs and one of them is the hydrosilylation reaction in which ILs immobilize la num [17] or rhod um [18] catalysts used during biphasic reactions in batch.”
BackgroundSelf-citationModification of (Poly)Siloxanes via Hydrosilylation Catalyzed by Rhodium Complex in Ionic Liquids
Marciniec, B., Maciejewski, H., Szubert, K., & Kurdykowska, M. (2006) · Monatshefte für Chemie - Chemical Monthly · doi:10.1007/s00706-006-0461-9 · Cited by 31 · cited 1×
“Imidazolium and pyridinium based ILs have been selected as a most suitable group of ILs for investigation in hydrosilylation reaction due to a few major factors: (i) proved good solubility of many catalysts in ILs containing these cations; (ii) high chemical stability of imidazolium and pyridinium IL systems; (iii) pr…”
BackgroundSelf-citationŚmiglak, M., Bridges, N. J., Dilip, M., & Rogers, R. D. (2008) · Chemistry - A European Journal · doi:10.1002/chem.200801811 · Cited by 30 · cited 2×
“However, the most useful feature of ILs is their tunability of properties possible through chemical modifications of cations or anions and hence adjustment of the intermolecular and interionic interactions [12].”
BackgroundPeng, J. J., Li, J. Y., Bai, Y., Gao, W., Qiu, H. Y., Wu, H., Deng, Y., & Lai, G. Q. (2007) · Journal of Molecular Catalysis A Chemical · doi:10.1016/j.molcata.2007.08.030 · Cited by 27
New approach to hydrosilylation reaction in ionic liquids as solvent in microreactor system
Kukawka, R., Pawlowska-Zygarowicz, A., Dutkiewicz, M., Maciejewski, H., & Śmiglak, M. (2016) · RSC Advances · doi:10.1039/c6ra08278e · Cited by 23 · cited 1×
“Our screening research highlighted the most promising ILs as candidates for study in flow-through microreactor systems [30], which we are going to conduct in the near future.”
BackgroundSelf-citation
Cited by
Ionic Liquids in Metal, Photo-, Electro-, and (Bio) Catalysis
Dupont, J., Leal, B. C., Lozano, P., Monteiro, A. L., Migowski, P., & Scholten, J. D. (2024) · Chemical Reviews · doi:10.1021/acs.chemrev.3c00379 · Cited by 218
Special Issue: “Organic Reactions in Green Solvents”
Sperry, J., & García‐Álvarez, J. (2016) · Molecules · doi:10.3390/molecules21111527 · Cited by 31
“Furthermore, Smiglak and co-workers have found that a biphasic system containing an ionic liquid (both imidazolium and pyridinium salts are employed) not miscible with the substrate (1-octene) is the reaction media of choice to accomplish the hydrosilylation of the desired olefin catalyzed by inorganic platinum or rho…”
He, W., Yan, F., Jia, Q., Xia, S., & Wang, Q. (2017) · Journal of Chemical & Engineering Data · doi:10.1021/acs.jced.7b00422 · Cited by 30
Jankowska‐Wajda, M., Kukawka, R., Śmiglak, M., & Maciejewski, H. (2018) · New Journal of Chemistry · doi:10.1039/c7nj04396a · Cited by 23
Self-citationJankowska‐Wajda, M., Bartlewicz, O., Szpecht, A., Zajac, A., Śmiglak, M., & Maciejewski, H. (2019) · RSC Advances · doi:10.1039/c9ra05948b · Cited by 23
Self-citation
Metadata
- Authors
- Zielinski, W., Kukawka, R., Maciejewski, H., & Smiglak, M.
- Affiliations
- Poznan Science and Technology Park, Adam Mickiewicz University Foundation, 46 Rubież ST., 61-612 Poznań, Poland
- Adam Mickiewicz University in Poznań (PL)
- Venue
- Molecules
- Publisher
- MDPI AG
- Published
- 2016-08-24
- Volume
- 21
- Issue
- 9
- Pages
- 1115
- ISSN
- 1420-3049 (ISSN-L)
- PMC
- PMC6274437
- OpenAlex
- W2512353041
- Semantic Scholar
- aab7c2f926788150e73919af90965bd68d7dd473
- Cited by
- 30
- References
- 28
- Citations by year
- 2025: 1 · 2024: 2 · 2023: 3 · 2022: 4 · 2021: 6 · 2020: 5 · 2019: 4 · 2018: 2 · 2017: 2 · 2016: 1
- FWCI
- 1.00
- Type
- journal article
- Language
- en
- Update notices
- correction (2016-08-24)
- Open access
- gold
- doi.org
- Licence
- Locations
- Molecules (publishedVersion, cc-by)
- Europe PMC (PubMed Central) (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- National Science Centre, Poland (Program OPUS 2012/05/B/ST5/00375)
- Topics
- Physical Sciences › Chemistry › Physical and Theoretical Chemistry › Ionic liquids properties and applications
- Physical Sciences › Chemistry › Organic Chemistry › Organoboron and organosilicon chemistry
- Physical Sciences › Chemistry › Organic Chemistry › N-Heterocyclic Carbenes in Organic and Inorganic Chemistry
- Keywords
- ionic liquids, hydrosilylation, rhodium catalysts, platinum catalysts, imidazolium ionic liquids, pyridinium ionic liquids, catalyst activation, biphasic catalysis, catalyst recycling, organometallic catalysts
- MeSH terms
- Catalysis, Octanes, Platinum, Rhodium, Siloxanes, Ionic Liquids
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-10-11, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-11 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.