The DOI matches its Crossref record; 53 of the 54 references it cites were found in a registry or an index; 16 of the 68 sources its claims cite were checked for support.
Production of Biochar from Plantain Rachis and Cassava Peel Towards Sustainable Management of Caribbean Agricultural Waste
Open accessAbstract
The Caribbean faces many environmental issues, and the mitigation and adaptation strategies to address the challenges of global warming are not sufficient in this geographical region. Considering that agriculture is a relevant activity in most countries around this region, our study proposes to enhance Caribbean waste management by transitioning to a sustainable and resilient process in the framework of a green, circular economy. The research has been focused on the thermochemical transformation of the typical residues of Caribbean farm products (plantain rachis, and cassava peel). Biochar samples were synthesized from these biomasses by the slow pyrolysis method at different temperatures (300 °C, 400 °C, and 500 °C). Biochar samples with a smooth surface were synthesized from plantain rachis biomass, while biochar samples with a porous surface were obtained from cassava peel biomass. At the same pyrolysis temperature, all biochar samples derived from plantain rachis exhibited higher production biochar yields than those biochar samples derived from cassava peel. The yield percentages were determined to be 65.7% and 62.0% at a pyrolysis temperature of 300 °C; 45.6% and 37.5% at 400 °C; and 33.7% and 25.4% at 500 °C, respectively. XRD measurements revealed that both biomass-derived biochar samples were found to be enriched with several compounds, such as kalicinite, arcanite, sylvite, CaO3Si, and MgO3Si, which vary according to the pyrolysis temperature. FTIR analysis revealed the presence of carbonyl and carboxyl functional groups on the surface of all biochar samples. However, only the aliphatic functional groups were observed on the surface of the biochar samples derived from cassava peel. These characteristics are of particular relevance due to their potential application in soil amendment or water remediation.
Overview
CoChat Summary
TL;DR
This study produced biochar from plantain rachis (PR) and cassava peel (CP) by slow pyrolysis at 300, 400, and 500 °C and characterized yield, morphology, elemental composition, crystalline phases, and surface functional groups. PR biochar had higher yields and smoother surfaces, while CP biochar was porous and CP-500 showed the most favorable properties for potential soil amendment or water remediation.
Key findings
- Biochar yield decreased with increasing pyrolysis temperature for both feedstocks: PR yields were 65.7%, 45.6%, and 33.7% at 300, 400, and 500 °C; CP yields were 62.0%, 37.5%, and 25.4% at the same temperatures. At each temperature, PR biochar had higher yield than CP biochar.
- PR biochar had a smooth surface with almost imperceptible porosity at 300 and 400 °C and holes >20 µm at 500 °C. CP biochar was porous, with pore diameters of 2.0–6.7 µm for CP-300, 1.3–5.7 µm for CP-400, and 1.2–3.0 µm for CP-500.
- EDX showed carbon, oxygen, and potassium as the highest-concentration elements, with calcium, silicon, phosphorus, and magnesium also detected. Carbon and potassium proportions tended to increase with pyrolysis temperature in CP biochar, and potassium also increased with temperature in PR biochar.
- XRD detected compounds including kalicinite, arcanite, sylvite, CaO3Si, and MgO3Si, varying by pyrolysis temperature. FTIR showed carbonyl and carboxyl groups on all biochar surfaces, while aliphatic functional groups were observed only on CP biochar.
Methods
- Plantain rachis and cassava peel were collected from two small-scale farms in Palmar de Varela, Atlántico, Colombia; biomass was washed three times with deionized water and dried at 90 °C for 12 h.
- Biochar was produced by slow pyrolysis in a muffle furnace under nitrogen flow (0.5 L/min) for 30 min at 300, 400, and 500 °C, with a heating rate of 15 °C/min; each experiment was repeated five times. Yield and moisture content were determined using ASTM D3173 and D3175.
- Characterization included TGA from room temperature to 850 °C at 15 °C/min, SEM/EDX, XRD, and ATR-FTIR over 400–4000 cm⁻¹ with 16 scans per sample.
Limitations
- The paper states that adsorption measurements are necessary to estimate an accurate average pore diameter in the biochar samples. It also notes that literature lacks consensus on the effect of pyrolysis temperature on biochar pore size, because feedstock strongly influences physical properties.
- Evident from the text: no BET surface area, adsorption, or direct soil/water remediation experiments were performed; application claims are based on characterization and prior literature rather than tested performance.
- Evident from the text: the study is limited to two local farms in one Colombian Caribbean locality and three pyrolysis temperatures, so broader feedstock and geographic variability are not assessed.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
12 Valid · 3 Not valid · 26 Not checked · 55 Own results and interpretations
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“As in our case, a comparison of the results reported by other authors regarding biochar obtained from PR and CP clearly indicates that, although the PR biochar does contain pores, its porosity tends to be much lower than the CP biochar.”
What the sources say
- Could not verifycites [27] Abdullah, 2023, Banana pseudo-stem biochar derived from slow and fast pyrolysis process, Heliyon sourceExperimental — accuracy not yet measured
The Results and discussion section reports pores in banana pseudo-stem biochar and compares slow with fast pyrolysis. Our copy does not report porosity for plantain rachis or cassava peel biochar, or compare the two (searched: plantain rachis, cassava peel, pores). (LLM, conf=0.78)
- Not checked — no full text of the sourcecites [28] Odeyemi, 2023, Valorization of waste cassava peel into biochar: An alternative to electrically-powered process. Total Environ, Res. Themes source
- Not checked — no full text of the sourcecites [29] Hamissou, 2023, Valorization of cassava peelings into biochar: Physical and chemical characterizations of biochar prepared for agricultural purposes, Sci. Afr. source
boosted- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“due to the thermal degradation leading to a substantial loss of oxygen atoms [42,44,45]”
What the sources say
- Not checked — no full text of the sourcecites [42] Xue, 2019, Pyrolysis of sewage sludge by electromagnetic induction: Biochar properties and application in adsorption removal of Pb(II), Cd(II) from aqueous solution, Waste Manag. source
- Partly supportedcites [44] Behazin, 2015, Mechanical, Chemical, and Physical Properties of Wood and Perennial Grass Biochars for Possible Composite Application, BioRes sourceExperimental — accuracy not yet measured
The Introduction describes pyrolysis as thermal degradation, and Results and Discussion assigns the 1700 cm-1 peak to carbonyl groups. But the paper compares biochars produced at an average of 500 °C; it does not show that increasing pyrolysis temperature reduces that peak or causes a substantial loss of oxygen atoms in CP biochar. (LLM, conf=0.84)
- Could not verifycites [45] Freitas, A.M., Nair, V.D., and Harris, W.G. (2020). Biochar as Influenced by Feedstock Variability: Implications and Opportunities for Phosphorus Management. Front. Sustain. Food Syst., 4. sourceExperimental — accuracy not yet measured
The Solid State Characterization section (page unavailable) describes XRD and SEM-EDS analyses, not infrared peaks near 1700 cm⁻¹. Searches for CP biochar, those peaks, and oxygen loss with increasing pyrolysis temperature found no passage addressing the proposed explanation. (LLM, conf=0.76)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Several studies have shown some compounds of biochar can stabilize organic matter in soils by means of carbonates and silicates of calcium and magnesium because they tend to raise the pH, neutralizing the acidity in water-wet soils, a fundamental aspect to achieving an efficient absorption of minerals [44,45,53].”
What the sources say
- Could not verifycites [44] Behazin, 2015, Mechanical, Chemical, and Physical Properties of Wood and Perennial Grass Biochars for Possible Composite Application, BioRes sourceExperimental — accuracy not yet measured
Split into 2 atoms — 0 confirmed, 0 partially supported, 0 disputed, 0 misattributed, 2 unverifiable. Expand the claim to see per-atom verdicts.
- Partly supportedcites [45] Freitas, A.M., Nair, V.D., and Harris, W.G. (2020). Biochar as Influenced by Feedstock Variability: Implications and Opportunities for Phosphorus Management. Front. Sustain. Food Syst., 4. sourceExperimental — accuracy not yet measured
Split into 2 atoms — 0 confirmed, 2 partially supported, 0 disputed, 0 misattributed, 0 unverifiable. Expand the claim to see per-atom verdicts.
- Not checked — no full text of the sourcecites [53] Amoakwah, 2023, Impact of silicate and lime application on soil fertility and temporal changes in soil properties and carbon stocks in a temperate ecosystem, Geoderma source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“These peaks are related to the stretching vibrations of the C -H bond of aliphatic functional groups with asymmetrical and symmetrical stretching at 2935 cm -1 and 2885 cm -1 , respectively [42,43].”
What the sources say
- Not checked — no full text of the sourcecites [42] Xue, 2019, Pyrolysis of sewage sludge by electromagnetic induction: Biochar properties and application in adsorption removal of Pb(II), Cd(II) from aqueous solution, Waste Manag. source
- Partly supportedcites [43] Sahoo, 2021, Production and characterization of biochar produced from slow pyrolysis of pigeon pea stalk and bamboo, Clean. Eng. Technol. sourceExperimental — accuracy not yet measured
Section 3.6 (page not provided) assigns a 2920 cm⁻¹ band to CH₂ stretching in aliphatic groups, supporting the general interpretation. It does not identify peaks at 2935 and 2885 cm⁻¹ or assign them to asymmetrical and symmetrical stretching, respectively; it also does not place these peaks in the stated 3000–3200 cm⁻¹ range. (LLM, conf=0.85)
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Regarding the porous surface of the CP biochar samples, the SEM images show the average pore size tends to decrease with increasing pyrolysis temperature”
hedgedstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
41 more claims
Create a free account to see all 96 claims and every source verdict.
- It may state two separate claims as one. 28
- Probably not a substantial claim. 27
- Borderline: one of the tests for a substantial claim is unclear. 1
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Abstract
“FTIR analysis revealed the presence of carbonyl and carboxyl functional groups on the surface of all biochar samples.”
§ 3.3.3. Fourier Transform Infrared Spectroscopy Analysis
“| 1700-1740 C=C and C=O stretching of carbonyl and carboxyl groups | ✓ | - | - | ✓ | ✓ ↓ | - |”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 3.3.2. Energy Dispersive X-Ray (EDX) and X-Ray Diffraction Analysis
“These last three compounds have also been evidenced in the XRD pattern of the CP-500 sample, but it reveals other peaks related to arcanite (K2O4S) and carbonyl dichloride (CCl2O) compounds (Figure 6b).”
§ 3.3.2. Energy Dispersive X-Ray (EDX) and X-Ray Diffraction Analysis
“| K 2 O 4 S | | ✓ | | | | |”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 3.3.1. Scanning Electron Microscopy Analysis
“the presence of holes with large diameters (>20 µ m) for the sample pyrolyzed at 500 ◦ C (Figure 2c).”
§ 3.3.1. Scanning Electron Microscopy Analysis
“Figure 2. Top-view SEM images of ( a ) PR biomass; ( b ) PR biochar pyrolyzed at 300 ◦ C; ( c ) PR biochar pyrolyzed at 400 ◦ C; ( d ) PR biochar pyrolyzed at 500 ◦ C.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 3.1. Degradation Process of Biomass
“| Paper pulp | 3.46 | 58.03 | 38.51 | [20] |”
§ References
“20. Mustofa, A. Bioethanol Production From Banana Stem By Using Simultaneous Saccharification and Fermentation (SSF).”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 3.3.3. Fourier Transform Infrared Spectroscopy Analysis
“The spectra of CP biochar samples reveal other peaks between 3000 cm -1 and 3200 cm -1 , but these are almost undetectable in the spectra of PR biochar samples.”
§ 3.3.3. Fourier Transform Infrared Spectroscopy Analysis
“These peaks are related to the stretching vibrations of the C -H bond of aliphatic functional groups with asymmetrical and symmetrical stretching at 2935 cm -1 and 2885 cm -1 , respectively [42,43].”
1 more finding
Create a free account to see every finding of this check.
Citations
Cites
Characteristics of hemicellulose, cellulose and lignin pyrolysis
Yang, H., Yan, R., Chen, H., Lee, D. H., & Zheng, C. (2007) · Fuel · doi:10.1016/j.fuel.2006.12.013 · Cited by 8,155
Biochar as a sorbent for contaminant management in soil and water: A review
Ahmad, M., Rajapaksha, A. U., Lim, J. E., Zhang, M., Bolan, N., Mohan, D., Vithanage, M., Lee, S. S., & Ok, Y. S. (2014) · Chemosphere · doi:10.1016/j.chemosphere.2013.10.071 · Cited by 4,662
Collard, F.-X., & Blin, J. (2014) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2014.06.013 · Cited by 1,905
Weber, K., & Quicker, P. (2018) · Fuel · doi:10.1016/j.fuel.2017.12.054 · Cited by 1,522
Screening biochars for heavy metal retention in soil: Role of oxygen functional groups
Uchimiya, M., Chang, S., & Klasson, K. T. (2011) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2011.03.063 · Cited by 678
Li, Y., Xing, B., Ding, Y., Han, X., & Wang, S. (2020) · Bioresource Technology · doi:10.1016/j.biortech.2020.123614 · Cited by 576
Lv, D., Xu, M., Liu, X., Zhan, Z., Li, Z., & Yao, H. (2010) · Fuel Processing Technology · doi:10.1016/j.fuproc.2009.09.014 · Cited by 479
An Overview of Recent Developments in Biomass Pyrolysis Technologies
Uddin, M. N., Techato, K., Taweekun, J., Rahman, M. M., Rasul, M. G., Mahlia, T. M. I., & Ashrafur, S. M. (2018) · Energies · doi:10.3390/en11113115 · Cited by 377
Sahoo, S. S., Vijay, V. K., Chandra, R., & Kumar, H. (2021) · Cleaner Engineering and Technology · doi:10.1016/j.clet.2021.100101 · Cited by 361
Seow, Y. X., Tan, Y. H., Mubarak, N. M., Kansedo, J., Khalid, M., Ibrahim, M. L., & Ghasemi, M. (2022) · Journal of Environmental Chemical Engineering · doi:10.1016/j.jece.2021.107017 · Cited by 338
Cited by
Sustainable removal of Cd(II) and Cr(VI) from aqueous solution via agro-waste derived biochar
Din, S. U., Al‐Ahmary, K. M., AL-Mhyawi, S. R., et al. (2026) · Scientific Reports · doi:10.1038/s41598-026-40608-1 · Cited by 4
“A further sharp decline in mass was seen between 350 and 450 °C, which corresponds to the decomposition of cellulose followed by the release of volatile organic matter 32 .”
InfluentialUnsomsri, N., Wiriyasart, S., & Kaewluan, S. (2026) · Applications in Energy and Combustion Science · doi:10.1016/j.jaecs.2026.100538 · Cited by 1
Biochar and bamboo ash in black cotton soil improvement: A review of engineering performance
Ujong, J. A., Umar, S. Y., Umaru, I., Abdulkarim, I. I., & Alaneme, G. U. (2026) · Environmental Progress & Sustainable Energy · doi:10.1002/ep.70588 · Cited by 1
Gonzalez, Y. N., Mello, F. F. D. C., & Lal, R. (2026) · Advances in agronomy · doi:10.1016/bs.agron.2026.07.003
Metadata
- Authors
- Herazo, A. P., Zambrano, A., Marín, L., Mass, J., & Montenegro, D. N.
- Affiliations
- Universidad del Atlántico (CO)
- Universidad del Valle (CO)
- Universidad del Norte (CO)
- Corresponding author
- Montenegro, Diana Nathalie
- Venue
- Processes
- Publisher
- MDPI AG
- Published
- 2025-06-29
- Volume
- 13
- Issue
- 7
- Pages
- 2059
- ISSN
- 2227-9717 (ISSN-L)
- OpenAlex
- W4411825723
- Cited by
- 4
- References
- 54
- Citations by year
- 2026: 4
- FWCI
- 0.98
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Processes (publishedVersion, cc-by)
- Topics
- Physical Sciences › Energy › Fuel Technology › Thermochemical Biomass Conversion Processes
- Physical Sciences › Environmental Science › Water Science and Technology › Adsorption and biosorption for pollutant removal
- Life Sciences › Agricultural and Biological Sciences › Soil Science › Soil Carbon and Nitrogen Dynamics
- Keywords
- biochar, cassava peel, agricultural waste management, slow pyrolysis, pyrolysis temperature, biochar yield, surface functional groups, mineral composition, circular economy, soil amendment, water remediation, Caribbean agriculture
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-05, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-05 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Production of Biochar from Plantain Rachis and Cassava Peel Towards Sustainable Management of Caribbean Agricultural Waste. https://app.cochat.ai/papers/10.3390/pr13072059
- The paper
- Herazo, A. P., Zambrano, A., Marín, L., Mass, J., & Montenegro, D. N. (2025). Production of Biochar from Plantain Rachis and Cassava Peel Towards Sustainable Management of Caribbean Agricultural Waste. Processes. https://doi.org/10.3390/pr13072059
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.