Student or educator? Sign up with your school email and get 6 months of Pro free.
CoChat

The DOI matches its Crossref record; 51 of the 51 references it cites were found in a registry or an index; none of the 25 sources its claims cite is checked for support yet.

Accuracy of Copernicus Altimeter Water Level Data in Italian Rivers Accounting for Narrow River Sections

Open access
Deidda, Cristina, De Michele, Carlo, Arslan, Ali, Pecora, Silvano, Taburet, Nicolas · 2021 · Remote Sensing

Abstract

Information about water level is essential for hydrological monitoring and flood/drought risk assessment. In a large part of Italian river network, in situ instruments for measuring water level are rare or lacking. Here we consider the satellite measurements of water level retrieved by Copernicus altimetric missions (Sentinel 3A, Sentinel 3B, Jason 2/3), and compare these with in situ data, from 19 gauging stations in Italy with a river section in the range of [50, 555] m. The results highlight the potentiality of altimetric satellite measurements for water level retrieval in a case study of Italian rivers. By comparing synchronous satellite and in situ water level difference (i.e., difference between two successive measurements in time of satellite data compared to the difference of two successive measurements in time of in situ data), we found a median value of Pearson correlation of 0.79 and 0.37 m of RMSE. Then, from water level differences, we extracted the satellite water level values with two different procedures: (1) assuming as the initial water level of the satellite measurements the first joint measurement (satellite–in situ data) and (2) calibrating the initial water level, minimizing the mean absolute error metric. The results show the feasibility of using satellite data for water level retrieval in an operative and automatic perspective.

Overview

CoChat Summary

TL;DR

This study compares Copernicus satellite altimeter water levels from Sentinel 3A/3B and Jason 2/3 with in situ gauging data at 22 satellite–in situ pairs on Italian rivers, including sections as narrow as 50 m. It finds feasible water-level retrieval, with median correlation 0.87 and RMSE 0.27 m after calibrating the initial water level, and no clear dependence of performance on river width for Sentinel satellites.

Key findings

  • For water-level differences, the median Pearson correlation was 0.79 and median RMSE was 0.37 m; 68% of pairs had R > 0.7 and 41% had RMSE < 0.3 m.
  • For absolute water levels with the initial value imposed, median R was 0.87, RMSE 0.38 m, MBE −0.07 m, and MAE 0.28 m; after calibrating the initial water level by minimizing MAE, median RMSE was 0.27 m, MBE −0.02 m, and MAE 0.19 m, while R did not change.
  • For sections <100 m wide (10 pairs), median R was 0.77, RMSE 0.38 m, MBE 0.025 m, and MAE 0.22 m; for Sentinel 3A only in these narrow sections, median R was 0.87, RMSE 0.23 m, MBE −0.02 m, and MAE 0.14 m.
  • For the largest sections [260–555] m, median R was 0.95, RMSE 0.26 m, MBE −0.03 m, and MAE 0.16 m; Sentinel 3A showed better agreement than Jason 2/3 across river widths.

Methods

  • Used Copernicus Global Land Level 3 water-level products from Sentinel 3A, Sentinel 3B, and Jason 2/3 virtual stations, compared with in situ data from 19 Italian gauging stations, yielding 22 satellite–in situ pairs with river section widths [50, 555] m; periods were 2016–2020 for Sentinel 3A, 2018–2020 for Sentinel 3B, and 2008–2020 for Jason.
  • Pair selection required distance <100 km (actual pairs [0.05, 11.39] km), comparable hydraulic and geometric/morphological conditions, and no intervening interference such as lakes/dams, tributaries, bifurcations, diversions, obstacles, or section/slope changes; time matching allowed a maximum 30 min difference.
  • Computed Pearson correlation (R), RMSE, MBE, and MAE for water-level differences and absolute water levels; absolute levels used two procedures: imposing equality at the first joint satellite–in situ measurement, and calibrating the initial water level to minimize MAE using R’s optimize function.

Limitations

  • Stated: satellite time coverage is coarse (up to 30 days); low-water sand benches or wet river boundaries can degrade altimeter accuracy; small along-river extent may not represent seasonal spatial variation; altimeters can struggle at very high altitudes and in steep topographic relief; and the official Copernicus river validation had a minimum 300 m width, motivating this <300 m assessment.
  • Stated: all selected in situ stations are at low altitude (0–186 m a.s.l.), so the study cannot assess the altitude–performance relationship reported by Jiang et al.; outliers may come from in situ instrument errors or satellite issues from water reflections, vegetation, and topography.
  • Evident from the text: the sample is limited to 19 gauging stations/22 pairs in Italy, mostly on large rivers and lowland reaches, with strict pair-selection criteria (max distance 11 km, no hydrological interference), so results may not generalize to ungauged, mountainous, or highly interfered reaches; environment (meanders, surrounding water bodies, river orientation vs. ground track) appears to influence performance more than width.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.3390/rs13214456

Cites

51 of 51 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Figures

Figure 1 Location of virtual stations ( × ) and in situ stations ( △ ) in Italy. Orbit ground tracks of Jason 2/3, Satellite 3A, and Satellite 3B obtained from AVISO (Pass locator) [53] and ESA website. In the map are indicated only the regions for which satellite altimetric data are actually available.
Figure 1 Location of virtual stations ( × ) and in situ stations ( △ ) in Italy. Orbit ground tracks of Jason 2/3, Satellite 3A, and Satellite 3B obtained from AVISO (Pass locator) [53] and ESA website. In the map are indicated only the regions for which satellite altimetric data are actually available.CC-BY · From the PDF
Figure 2 Examples of virtual-in situ-coupled selection methodology: ( a ) discarded pair for the presence of interference, ( b ) selected pair. Base maps are taken from OpenStreetMap.
Figure 2 Examples of virtual-in situ-coupled selection methodology: ( a ) discarded pair for the presence of interference, ( b ) selected pair. Base maps are taken from OpenStreetMap.CC-BY · From the PDF
Image 3
CC-BY · From the PDF
Figure 4 ( a ) Boxplots of the differences (in situ water differences minus satellite water differences) for each of the 22 pairs, with different colors distinguishing the different satellites. ( b ) Boxplots sorted by river section width.
Figure 4 ( a ) Boxplots of the differences (in situ water differences minus satellite water differences) for each of the 22 pairs, with different colors distinguishing the different satellites. ( b ) Boxplots sorted by river section width.CC-BY · From the PDF
Figure 5 Po river at Ficarolo (Veneto): ( a ) temporal variability of satellite and in situ water level, where the satellite water levels are obtained by imposing the initial water level; ( b ) as in panel ( a ) but the initial water level was calibrated; ( c ) scatterplot satellite-in situ water levels given in panel ( a ); ( d ) scatterplot satellite-in situ water levels given in panel ( b ); ( e ) scatterplot satellite-in situ water level differences.
Figure 5 Po river at Ficarolo (Veneto): ( a ) temporal variability of satellite and in situ water level, where the satellite water levels are obtained by imposing the initial water level; ( b ) as in panel ( a ) but the initial water level was calibrated; ( c ) scatterplot satellite-in situ water levels given in panel ( a ); ( d ) scatterplot satellite-in situ water levels given in panel ( b ); ( e ) scatterplot satellite-in situ water level differences.CC-BY · From the PDF
Figure 6 Po river at Pontelagoscuro (Emilia Romagna): ( a ) temporal variability of satellite and in situ water levels, where the satellite water levels are obtained by imposing the initial water level; ( b ) as in panel ( a ) but the initial water level was calibrated; ( c ) scatterplot satellite-in situ water levels given in panel ( a ); ( d ) scatterplot satellite-in situ water levels given in panel ( b ); ( e ) scatterplot satellite-in situ water level differences.
Figure 6 Po river at Pontelagoscuro (Emilia Romagna): ( a ) temporal variability of satellite and in situ water levels, where the satellite water levels are obtained by imposing the initial water level; ( b ) as in panel ( a ) but the initial water level was calibrated; ( c ) scatterplot satellite-in situ water levels given in panel ( a ); ( d ) scatterplot satellite-in situ water levels given in panel ( b ); ( e ) scatterplot satellite-in situ water level differences.CC-BY · From the PDF
Figure 7 Map of the virtual stations (existing ones indicated with red circles and potential new ones indicated with blue circles) in Italy, for which the altimeter on board DEM (OLTC) is tuned to track the water [59] (V6 DEM was uploaded onboard Sentinel 3A at the end of August 2020 [57]). The quality check of time series of new targets is currently in process. If the new targets satisfy the quality requirements, they could be added to the existing virtual stations, permitting a coverage also of southern Italy and islands, in the next future.
Figure 7 Map of the virtual stations (existing ones indicated with red circles and potential new ones indicated with blue circles) in Italy, for which the altimeter on board DEM (OLTC) is tuned to track the water [59] (V6 DEM was uploaded onboard Sentinel 3A at the end of August 2020 [57]). The quality check of time series of new targets is currently in process. If the new targets satisfy the quality requirements, they could be added to the existing virtual stations, permitting a coverage also of southern Italy and islands, in the next future.CC-BY · From the PDF
Figure A1. Adige river at Badia Polesine (Veneto): ( a ) temporal variability of satellite and in situ water level, where the satellite water levels are obtained imposing the initial water level; ( b ) same as panel ( a ), but the initial water level was calibrated; ( c ) scatterplot satellite-in situ water levels given in panel ( a ); ( d ) scatterplot satellite-in situ water levels given in panel ( b ); ( e ) scatterplot satellite-in situ water level differences.
Figure A1. Adige river at Badia Polesine (Veneto): ( a ) temporal variability of satellite and in situ water level, where the satellite water levels are obtained imposing the initial water level; ( b ) same as panel ( a ), but the initial water level was calibrated; ( c ) scatterplot satellite-in situ water levels given in panel ( a ); ( d ) scatterplot satellite-in situ water levels given in panel ( b ); ( e ) scatterplot satellite-in situ water level differences.CC-BY · From the PDF
Figure A2. Po river at Boretto (Emilia Romagna): ( a ) temporal variability of satellite and in situ water level, where the satellite water levels are obtained imposing the initial water level; ( b ) same as panel ( a ) but the initial water level was calibrated; ( c ) scatterplot satellite-in situ water levels given in panel ( a ); ( d ) scatterplot satellite-in situ water levels given in panel ( b ); ( e ) scatterplot satellite-in situ water level differences.
Figure A2. Po river at Boretto (Emilia Romagna): ( a ) temporal variability of satellite and in situ water level, where the satellite water levels are obtained imposing the initial water level; ( b ) same as panel ( a ) but the initial water level was calibrated; ( c ) scatterplot satellite-in situ water levels given in panel ( a ); ( d ) scatterplot satellite-in situ water levels given in panel ( b ); ( e ) scatterplot satellite-in situ water level differences.CC-BY · From the PDF
Figure A3. Adige river at Boara Pisani (Veneto): ( a ) temporal variability of satellite and in situ water level, where the satellite water levels are obtained by imposing the initial water level; ( b ) same as in panel ( a ) but the initial water level was calibrated; ( c ) scatterplot satellite-in situ water levels given in panel ( a ); ( d ) scatterplot satellite-in situ water levels given in panel ( b ); ( e ) scatterplot satellite-in situ water level differences.
Figure A3. Adige river at Boara Pisani (Veneto): ( a ) temporal variability of satellite and in situ water level, where the satellite water levels are obtained by imposing the initial water level; ( b ) same as in panel ( a ) but the initial water level was calibrated; ( c ) scatterplot satellite-in situ water levels given in panel ( a ); ( d ) scatterplot satellite-in situ water levels given in panel ( b ); ( e ) scatterplot satellite-in situ water level differences.CC-BY · From the PDF
Image 11
CC-BY · From the PDF

Verification

Claims the paper makes

0 Valid · 1 Not valid · 15 Not checked · 45 Own results and interpretations

14 more claims

Create a free account to see all 61 claims and to verify the 25 references still open.

See all claims — free account
  • The quote only partly states this claim. 3
  • It may state two separate claims as one. 30
  • Probably not a substantial claim. 15

Create a free account to see these claims.

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

Each contradiction between two passages listed here was confirmed by an independent check.

1 of 1

Citations

Cites

Research works printed but not linked: 3

  1. Taburet, N., Vayre, M., Calmettes, B., Zawadzki, L., Paris, A., Calmant, S., and Crétaux, J.F. (2021, August 20). Copernicus Global Land Operations “Cryosphere and Water”: Quality Assessment Report—Lake and River Water Level, pp. 1–60. Available online: https://land.copernicus.eu/global.
  2. Fernández, J., Fernández, C., Féménias, P., and Peter, H. (2016, January 9–14). The Copernicus Sentinel-3 Mission. Proceedings of the ILRS Workshop 2016, Potsdam, Germany.
  3. Taburet, N., Zawadzki, L., Calmant, S., Crétaux, J.F., Mercier, F., and Vayre, M. (2021, August 20). Copernicus Global Land Operations “Cryosphere and Water”: Product User Manual—Lake and River Water Level; pp. 1–41. Available online: https://land.copernicus.eu/global.

Cited by

See all 11

Metadata

Authors
Deidda, C., De Michele, C., Arslan, A., Pecora, S., & Taburet, N.
Affiliations
  • Politecnico di Milano (IT)
  • Department of Civil and Environmental Engineering, Politecnico di Milano, 20133 Milano, Italy
  • Finnish Meteorological Institute (FI)
  • Autorità di Bacino del Fiume Po, 43121 Parma, Italy
  • Collecte Localisation Satellites (France) (FR)
Venue
Remote Sensing
Publisher
MDPI AG
Published
2021-11-05
Volume
13
Issue
21
Pages
4456
ISSN
2072-4292 (ISSN-L)
OpenAlex
W3214709340
Cited by
11
References
51
Citations by year
2026: 4 · 2025: 3 · 2024: 4
FWCI
0.31
Type
journal article
Language
en
Open access
Locations
  • Remote Sensing (publishedVersion, cc-by)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
  • Virtual Community of Pathological Anatomy (University of Castilla La Mancha) (submittedVersion)
  • VUBIR (Vrije Universiteit Brussel) (submittedVersion)
  • INFM-OAR (INFN Catania) (submittedVersion, cc-by)
  • Zenodo (CERN European Organization for Nuclear Research) (other-oa)
Funders
  • Regione Lazio
  • Regione Toscana
  • Regione Umbria
Topics
  • Physical Sciences › Environmental Science › Global and Planetary Change › Flood Risk Assessment and Management
  • Physical Sciences › Environmental Science › Water Science and Technology › Hydrology and Watershed Management Studies
  • Physical Sciences › Environmental Science › Environmental Engineering › Soil Moisture and Remote Sensing
Keywords
altimetry, Sentinel-3, Italian rivers, flood risk assessment, drought risk assessment, hydrological monitoring

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

A language model drew the claims from the paper on 2026-11-19, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).

A second model labelled each claim on 2026-11-19 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.