CoChat

3Cat-3/MOTS Nanosatellite Mission for Optical Multispectral and GNSS-R Earth Observation: Concept and Analysis

Open access
Castellví, Jordi, Camps, Adriano, Corbera, Jordi, Alamús, Ramon · 2018 · Sensors

The DOI matches its Crossref record; 15 of the 15 references it cites were found in a registry or an index; none of the 9 sources its claims cite is checked for support yet.

Abstract

This work summarizes the mission analysis of 3Cat-3/MOTS, including its payload results, power budget, thermal budget, and data budget.

Overview

CoChat Summary

## TL;DR

This paper presents the concept and mission analysis of 3Cat-3/MOTS, a 6U CubeSat for combined multispectral optical and GNSS-R Earth observation, aimed at soil moisture and land-cover change mapping. The study argues the mission is feasible but tightly constrained by power, data downlink, thermal control, and CubeSat volume limits.

## Key findings

  • The mission targets multispectral imagery from 400 nm to 870 nm with spatial resolution better than 30 m, swath wider than 30 km, SNR better than 30 dB in each band, revisit time under 10 days over Catalonia, and data fusion with GNSS-R for soil moisture mapping at 30 m resolution.
  • Orbit simulations at a 500 km altitude predict re-entry in 4.6 years, satisfying the stated mission requirement of at least 3 years and the <25-year reentry guideline.
  • The optical payload simulation gives images of 1.25 MP, about 1.9 MB per image, and roughly 4 Mbps of generated data at 100% duty cycle; the paper says this overwhelms typical S-band downlink capacities of less than 4 Mbps.
  • With a 0.1 Mbps downlink, onboard storage keeps growing and data are lost; increasing the link to 0.5 Mbps makes the output flux higher than the input flux so data are rapidly downloaded.
  • The paper reports that eclipse periods account for approximately 30% to 31% of the orbit, which makes power a bottleneck and requires strict duty-cycle control.
  • A 3 mm aluminum plate shielding mass of 84.3 g is reported as minimizing both accumulated radiation dose and shield mass.

## Methods

  • Concept and feasibility study for a 6U CubeSat mission combining a VNIR multispectral optical sensor and a GNSS reflectometer, with mission-level analysis of power, thermal, and data budgets.
  • Orbit and subsystem simulations used DRAMA-OSCAR GUI v.2.1.0 for orbital lifetime and SPENVIS for radiation analysis; mission performance was modeled with the MOTS End-to-end Performance Simulator (MEPS).
  • The analysis considered selected design assumptions including a 500 km orbit, 6U platform constraints, 80% MPPT/charger efficiency, 30% solar-panel efficiency, 2 GB onboard storage, and downlink scenarios of 0.1 Mbps and 0.5 Mbps.

## Limitations

  • The paper states that the final orbit will be “the best available one” because CubeSats are launched as piggyback payloads, so the proposed orbit may not be the one actually flown.
  • It notes that the GNSS-R radiometer is only a possible inclusion if it does not jeopardize the main mission in power, data, and platform design, indicating payload scope is constrained.
  • Evident from the text: the study is a mission analysis/concept paper with simulations, not a flight or experimental validation of the integrated 3Cat-3/MOTS system.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.3390/s18010140

Cites

15 of 15 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Figures

Figure 1 Apogee/Perigee Altitude history for the studied orbit (Start Year: 2019, Inclination: 55°, RAAN (Right Ascension of the Ascending Node): 8.32°, Arg. Peri.: 0°, Mean Anomaly 0°, and Area-to-Mass: 0.006 kg/m2). The initial orbital height for the simulation has been set to 500 km. Reentry will occur after 4.6 years, while the mission has an expected lifespan of 2 years. During this period, the changes in the orbital height are negligible for payload functioning purposes.
Figure 1 Apogee/Perigee Altitude history for the studied orbit (Start Year: 2019, Inclination: 55°, RAAN (Right Ascension of the Ascending Node): 8.32°, Arg. Peri.: 0°, Mean Anomaly 0°, and Area-to-Mass: 0.006 kg/m2). The initial orbital height for the simulation has been set to 500 km. Reentry will occur after 4.6 years, while the mission has an expected lifespan of 2 years. During this period, the changes in the orbital height are negligible for payload functioning purposes.CC BY · PubMed Central
Figure 2 Accumulated radiation dose (rad) as a function of the shielding thickness. The main contributors to the Total Ionizing Dose (TID) include trapped protons and electrons and Bremsstrahlung protons. The total dose accumulated is efficiently reduced up to a 5 mm shielding thickness.
Figure 2 Accumulated radiation dose (rad) as a function of the shielding thickness. The main contributors to the Total Ionizing Dose (TID) include trapped protons and electrons and Bremsstrahlung protons. The total dose accumulated is efficiently reduced up to a 5 mm shielding thickness.CC BY · PubMed Central
Figure 3 Target areas (TA) in red and ground stations (GS) in green considered for the simulation. The radii of the TAs (from left to right) are set to 3000 km, 3500 km, and 2000 km, respectively. The ground stations have a minimum elevation angle over the horizon of 10°.
Figure 3 Target areas (TA) in red and ground stations (GS) in green considered for the simulation. The radii of the TAs (from left to right) are set to 3000 km, 3500 km, and 2000 km, respectively. The ground stations have a minimum elevation angle over the horizon of 10°.CC BY · PubMed Central
Figure 4 Simulation of the 3Cat-3track (red), the swath of the optic instrument (red blurred), possible specular reflection points (green), the Sentinel 2A/B pass closer to the Catalan territory (cyan), and the swath of the optic instrument of the Sentinel 2A/B (cyan blurred).
Figure 4 Simulation of the 3Cat-3track (red), the swath of the optic instrument (red blurred), possible specular reflection points (green), the Sentinel 2A/B pass closer to the Catalan territory (cyan), and the swath of the optic instrument of the Sentinel 2A/B (cyan blurred).CC BY · PubMed Central
Figure 5 Conceptual diagram on the dependency of the activity of the different subsystems with the budgets that reflect the results of the simulation. UHF: ultra-high frequency; SD: secure digital.
Figure 5 Conceptual diagram on the dependency of the activity of the different subsystems with the budgets that reflect the results of the simulation. UHF: ultra-high frequency; SD: secure digital.CC BY · PubMed Central
Figure 6 Reflectivity data from Earth’s surface (source TOMS, Total Ozone Mapping Spectrometer). The original matrix of 360 × 288 cells has been reduced in a factor of 4 to lighten the computing time. TOMS-EP measured total ozone by observing both incoming solar energy and backscattered ultraviolet (UV). By comparing the amount of backscattered radiation to observations of incoming solar energy at identical wavelengths, it is possible to infer Earth’s albedo.
Figure 6 Reflectivity data from Earth’s surface (source TOMS, Total Ozone Mapping Spectrometer). The original matrix of 360 × 288 cells has been reduced in a factor of 4 to lighten the computing time. TOMS-EP measured total ozone by observing both incoming solar energy and backscattered ultraviolet (UV). By comparing the amount of backscattered radiation to observations of incoming solar energy at identical wavelengths, it is possible to infer Earth’s albedo.CC BY · PubMed Central
Figure 7 Instantaneous effective area exposed to the Sun of each side of the 6U CubeSat along 5 days of simulation. Each side of the CubeSat presents a different angle towards the Sun, which affects the collected energy.
Figure 7 Instantaneous effective area exposed to the Sun of each side of the 6U CubeSat along 5 days of simulation. Each side of the CubeSat presents a different angle towards the Sun, which affects the collected energy.CC BY · PubMed Central
Figure 8 3Cat-3/MOTS power budget. In blue is the instantaneous charge of the batteries (A·h) during 5 days of simulation. After an initial transition period, the scheduler takes command and the budget is more predictable because the activity and duty cycles of the devices are firmly controlled. The green, blue, and red levels are at 90%, 75%, and 25% Depth of Discharge (DoD), respectively. The total battery capacity is 20.8 A·h, in a configuration of two modules of 10.4 A·h.
Figure 8 3Cat-3/MOTS power budget. In blue is the instantaneous charge of the batteries (A·h) during 5 days of simulation. After an initial transition period, the scheduler takes command and the budget is more predictable because the activity and duty cycles of the devices are firmly controlled. The green, blue, and red levels are at 90%, 75%, and 25% Depth of Discharge (DoD), respectively. The total battery capacity is 20.8 A·h, in a configuration of two modules of 10.4 A·h.CC BY · PubMed Central
Figure 9 3Cat-3/MOTS thermal budget. In blue/red, instantaneous satellite temperature (°C) for a 5-day simulation. The red color shows the temperature when there is no solar eclipse. On the contrary, the blue color shows the temperature while in Sun eclipse periods. The satellite’s initial temperature has been set to 25 °C. There is a noticeable permanent regime temperature around 10 °C. The maximum temperature reached is approximately 27 °C and the minimum temperature 4 °C. The absorptance and emittance coefficients of the coating (polished beryllium) are 0.44 and 0.01, respectively.
Figure 9 3Cat-3/MOTS thermal budget. In blue/red, instantaneous satellite temperature (°C) for a 5-day simulation. The red color shows the temperature when there is no solar eclipse. On the contrary, the blue color shows the temperature while in Sun eclipse periods. The satellite’s initial temperature has been set to 25 °C. There is a noticeable permanent regime temperature around 10 °C. The maximum temperature reached is approximately 27 °C and the minimum temperature 4 °C. The absorptance and emittance coefficients of the coating (polished beryllium) are 0.44 and 0.01, respectively.CC BY · PubMed Central
Figure 10 3Cat-3/MOTS thermal budget. In blue/red is the instantaneous satellite temperature (°C) for a 5-day simulation. The red color shows the temperature when there is no solar eclipse. On the contrary, the blue color shows the temperature while in Sun eclipse periods. The satellite’s initial temperature has been set to 25 °C. There is a noticeable permanent regime temperature around −2 °C. The maximum temperature reached is the initial temperature at 25 °C and the minimum is −11 °C. The absorptance and emittance coefficients of the coating (black paint) are 0.95 and 0.85m respectively.
Figure 10 3Cat-3/MOTS thermal budget. In blue/red is the instantaneous satellite temperature (°C) for a 5-day simulation. The red color shows the temperature when there is no solar eclipse. On the contrary, the blue color shows the temperature while in Sun eclipse periods. The satellite’s initial temperature has been set to 25 °C. There is a noticeable permanent regime temperature around −2 °C. The maximum temperature reached is the initial temperature at 25 °C and the minimum is −11 °C. The absorptance and emittance coefficients of the coating (black paint) are 0.95 and 0.85m respectively.CC BY · PubMed Central
Figure 11 3Cat-3/MOTS contact time. In red, blue, and green is represented the contact with the ground stations described in Figure 2 (from left to right, respectively). In this particular case, the simulation lasts for 5 days and the total contact time is 377 min. This is approximately 5.3% of the orbital period. The minimum elevation over the horizon to stablish contact with the GS has been set to 10°.
Figure 11 3Cat-3/MOTS contact time. In red, blue, and green is represented the contact with the ground stations described in Figure 2 (from left to right, respectively). In this particular case, the simulation lasts for 5 days and the total contact time is 377 min. This is approximately 5.3% of the orbital period. The minimum elevation over the horizon to stablish contact with the GS has been set to 10°.CC BY · PubMed Central
Figure 12 3Cat-3/MOTS data budget. In blue is the instantaneous state of the on-board memory storage in Mb. In red is the acquisition time of the payloads for a 0.1 Mbps downlink rate and five days’ simulation. The memory is rapidly getting full due to the inconsistent rate between acquisition and download capability. This effect can be corrected by reducing the acquisition area and/or increasing the transmission rate. In this simulation, the TAs and GSs are described in Figure 3.
Figure 12 3Cat-3/MOTS data budget. In blue is the instantaneous state of the on-board memory storage in Mb. In red is the acquisition time of the payloads for a 0.1 Mbps downlink rate and five days’ simulation. The memory is rapidly getting full due to the inconsistent rate between acquisition and download capability. This effect can be corrected by reducing the acquisition area and/or increasing the transmission rate. In this simulation, the TAs and GSs are described in Figure 3.CC BY · PubMed Central
Figure 13 3Cat-3/MOTS data budget. In blue is the instantaneous state of the on-board memory storage in Mb. In red is the acquisition time of the payloads for a 0.5 Mbps downlink rate and five days’ simulation. The state of the memory is under control. The effect of Figure 12 has been corrected by increasing the transmission rate at 0.5 Mbps.
Figure 13 3Cat-3/MOTS data budget. In blue is the instantaneous state of the on-board memory storage in Mb. In red is the acquisition time of the payloads for a 0.5 Mbps downlink rate and five days’ simulation. The state of the memory is under control. The effect of Figure 12 has been corrected by increasing the transmission rate at 0.5 Mbps.CC BY · PubMed Central

Verification

Claims the paper makes

0 Valid · 6 Not valid · 8 Not checked · 32 Own results and interpretations

19 more claims

Create a free account to see all 46 claims and to verify the 1 reference still open.

See all claims — free account
  • Probably not a substantial claim. 14
  • It may state two separate claims as one. 15

Create a free account to see these claims.

Citations

Cites

Show all 15 references

Research works printed but not linked: 2

  1. Wertz, J.M., Sarzi-Amade, N., Shao, A., Taylor, C., and van Allen, R.E. (2012, January 13–16). Moderately Elliptical Very Low Orbits (MEVLOs) as a Long-Term Solution to Orbit Debris. Proceedings of the 26th Annual AIAA/USU Conference on Small Satellites, SSC12-IV-6, Logan, UT, USA.
  2. Qiao, L., Rizos, C., and Dempster, A.G. (2013, January 8–10). Analysis and Comparison of CubeSat Lifetime. Proceedings of the 12th Australian Space Development Conference, Adelaide, Australia.

Cited by

See all 12

Metadata

Authors
Castellví, J., Camps, A., Corbera, J., & Alamús, R.
Affiliations
  • Institut Cartogràfic i Geològic de Catalunya (ES)
  • Universitat Politècnica de Catalunya (ES)
  • Institut Cartogràfic i Geològic de Catalunya (ICGC), Parc de Montjuïc, 08038 Barcelona, Spain
Corresponding author
Castellví, Jordi
Venue
Sensors
Publisher
MDPI AG
Published
2018-01-06
Volume
18
Issue
1
Pages
140
ISSN
1424-8220 (ISSN-L)
OpenAlex
W2783394422
Cited by
12
References
15
Citations by year
2023: 2 · 2022: 4 · 2019: 5 · 2018: 1
FWCI
1.22
Type
journal article
Language
en
Open access
Locations
  • Sensors (publishedVersion, cc-by)
  • Europe PMC (PubMed Central) (publishedVersion, cc-by)
  • PubMed Central (publishedVersion, cc-by)
  • PubMed (publishedVersion)
  • RECERCAT (Consorci de Serveis Universitaris de Catalunya) (acceptedVersion, other-oa)
  • LA Referencia (Red Federada de Repositorios Institucionales de Publicaciones Científicas) (submittedVersion, cc-by)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
  • UPCommons institutional repository (Universitat Politècnica de Catalunya) (submittedVersion, cc-by)
Funders
  • Generalitat de Catalunya
  • Ministerio de Economía y Competitividad (MDM2016-0600, ESP2015-70014-C2-1-R)
  • Universitat Politècnica de Catalunya
  • Agència de Gestió d'Ajuts Universitaris i de Recerca
Topics
  • Physical Sciences › Engineering › Aerospace Engineering › Spacecraft Design and Technology
  • Physical Sciences › Engineering › Aerospace Engineering › GNSS positioning and interference
  • Physical Sciences › Environmental Science › Environmental Engineering › Soil Moisture and Remote Sensing
Keywords
CubeSat, nanosatellites, GNSS reflectometry, Earth observation, data fusion, power budget, thermal budget, soil moisture, land cover change, climatic variables, small satellite constellations

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).

A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: 3Cat-3/MOTS Nanosatellite Mission for Optical Multispectral and GNSS-R Earth Observation: Concept and Analysis. https://app.cochat.ai/papers/10.3390/s18010140
The paper
Castellví, J., Camps, A., Corbera, J., & Alamús, R. (2018). 3Cat-3/MOTS Nanosatellite Mission for Optical Multispectral and GNSS-R Earth Observation: Concept and Analysis. Sensors. https://doi.org/10.3390/s18010140

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.