Demulsifier Selection Guideline for Destabilizing Water-in-Oil Emulsion for both non-EOR and EOR Application
Open accessThe DOI matches its Crossref record; 26 of the 26 references it cites were found in a registry or an index; none of the 53 sources its claims cite is checked for support yet.
Abstract
The most common method for resolving water-in-oil (W/O) emulsions is chemical demulsification. The bottle test is a recommended procedure to analyze a combination of essential parameters such as the demulsifier dosage, residence time, heat, degree of agitation to generate the emulsion and agitation effects after demulsifier injection. It is an extensive and time-consuming selection procedure. Furthermore, the previous demulsifier selection guideline reported in the literature had limitations and was not suitable for the Southeast Asia region. This study describes the development of a new demulsifier selection guideline that relates the demulsifier properties to the crude oil characteristics and is more representative for resolving emulsions in the Southeast Asia environment. In developing the selection guideline, four types of synthetic crude were used, with the crude API ranging from 27˚ to 40˚. Sixteen demulsifiers with a relative solubility number (RSN) ranging from 11 to 21 were evaluated comprising resin alkoxylate and modified polyol base demulsifiers. An emulsion test matrix was developed by creating emulsions with different wax contents, asphaltene content and solid contents in the crude oil; then, the demulsifier was screened for all the matrices. Based on the demulsification bottle test completion for all the test matrices, the demulsifier selection guideline was developed and then validated with the blind test in resolving emulsions from the actual crude. The validation results achieved an 86.7% match rate between the guideline output and the lab experimental result. This proved that good agreement had been established between the demulsifier properties and the crude characteristics.
Overview
CoChat Summary
TL;DR
The paper develops and validates a demulsifier selection guideline for water-in-oil emulsions using synthetic and actual Southeast Asia crude oils, with the key selector being demulsifier RSN matched to crude-oil properties. In blind testing on 15 crude samples from 5 fields, the guideline matched lab results 86.7% of the time.
Key findings
- For non-EOR emulsions, the best-performing demulsifiers were generally in the high RSN range, especially RSN 19 to 21.
- Wax content changed the needed RSN: RSN 19 worked for wax content of 6% and below, while higher wax content required RSN 21.
- Temperature mattered: at 35 °C, demulsifier performance decreased, especially for API 37 crude with high wax content; RSN 19 still worked efficiently at low temperature.
- In the blind test, 14 of 15 crude samples were matched by the guideline, yielding an overall matching rate of 86.7%.
Methods
- Developed synthetic crude oils with API ranges from 27 to 40 and varied wax, asphaltene, and solid contents; evaluated 16 base demulsifiers with RSN 11 to 21.
- Used bottle tests for both non-EOR and EOR emulsions: 50:50 crude/brine mixtures, 100 ppm demulsifier for non-EOR tests, and field-specific surfactant conditions for EOR tests.
- Validated the guideline with a blind test on 15 actual crude oil samples from 5 fields, comparing recommended RSN values against bottle-test performance.
Limitations
- The paper states the guideline was developed from Southeast Asia crudes and notes prior guidelines were not suitable for that region; this implies regional specificity, although it says the guideline may also apply outside Southeast Asia.
- The EOR demulsifier screening used a single base demulsifier without combining with other demulsifiers or solvents, so the paper notes it could be further optimized.
- The bottle-test approach is described as extensive and time-consuming; this is an evident practical limitation from the text.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures















Verification
Claims the paper makes
0 Valid · 1 Not valid · 53 Not checked · 65 Own results and interpretations
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The validation results achieved an 86.7% match rate between the guideline output and the lab experimental result.”
§ Demulsifier Selection Guideline for Destabilizing Water-in-Oil Emulsion for both non-EOR and EOR Application > Abstract
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
None of the sources cited for this claim have been checked yet.
In the paper
“From the fi gure, the demulsifi er performance reduced when the asphaltene content increased for both low and high crude oil API.”
§ Demulsifier Selection Guideline for Destabilizing Water-in-Oil Emulsion for both non-EOR and EOR Application > 3.2.3 Eff ect of Asphaltene
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“For a heavy crude oil of API 27, demulsifiers with RSN 16 work best for all asphaltene content between 1.2% and 1.8%, while for a light crude oil of API 40, demulsifiers with RSN 19 work best for all asphaltene content between 0.36% and 0.72%.”
- Also stated in: § 3.5. Demulsifier Selection from Demulsification Guideline · plain
“For heavy crude oil, demulsifiers with RSN 16 work best for all asphaltene content between 1.2% to 1.8%; while for light crude oil, demulsifiers with RSN 19 work best for all asphaltene content between 0.36% to 0.72%.”
§ Demulsifier Selection Guideline for Destabilizing Water-in-Oil Emulsion for both non-EOR and EOR Application > 3.2.3 Eff ect of Asphaltene
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Also stated in: § 3.5. Demulsifier Selection from Demulsification Guideline · plain
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Compared to this high RSN demulsifi er, the demulsifi er with RSN 19 was the most eff ective demulsifi er in resolving the emulsion for all the crude oil APIs except for crude oil API 37.”
§ Demulsifier Selection Guideline for Destabilizing Water-in-Oil Emulsion for both non-EOR and EOR Application > 3.2.1 Eff ect of Crude API and Wax Content
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“SARA analysis of the Vacuum Residue shows the asphaltene content was 6%.”
§ Demulsifier Selection Guideline for Destabilizing Water-in-Oil Emulsion for both non-EOR and EOR Application > 3.2.3 Eff ect of Asphaltene
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
66 more claims
Create a free account to see all 119 claims and to verify the 1 reference still open.
- It may state two separate claims as one. 33
- Probably not a substantial claim. 20
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ Demulsifier Selection Guideline for Destabilizing Water-in-Oil Emulsion for both non-EOR and EOR Application > 3.3 Emulsion Tendency Test (EOR Emulsion)
“For Field B EWAG and Field D EWAG application, the EWAG surfactant concentrations were 1000 ppm and 2700 ppm.”
§ Demulsifier Selection Guideline for Destabilizing Water-in-Oil Emulsion for both non-EOR and EOR Application > 4. CONCLUSION
“| EOR Surfactant Concentration (ppm) | 250 750 | 900 2700 | 900 2700 |”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Demulsifier Selection Guideline for Destabilizing Water-in-Oil Emulsion for both non-EOR and EOR Application > Abstract
“In developing the selection guideline, four types of synthetic crude were used, with the crude API ranging from 27˚ to 40˚.”
§ Demulsifier Selection Guideline for Destabilizing Water-in-Oil Emulsion for both non-EOR and EOR Application > 2.1 Materials
“As the basis for developing the demulsifier selection guideline for non EOR emulsion, four types of synthetic crude oil were used in the demulsifier bottle test with crude oil API ranges from 26˚ to 40˚.”
Citations
Cites
IOP Conference Series: Materials Science and Engineering
(2022) · IOP Conference Series: Materials Science and Engineering · doi:10.1088/1757-899x/1231/1/011001 · Cited by 10,357
The Effects of Inorganic Solid Particles on Water and Crude Oil Emulsion Stability
Sullivan, A. P., & Kilpatrick, P. K. (2002) · Industrial & Engineering Chemistry Research · doi:10.1021/ie010927n · Cited by 341 · cited 1×
“Small particles strongly enhance water-crude oil emulsion stability when interactions with asphaltenes promote particle adsorption at the oil–water interface (Sullivan and Kilpatrick, 2002).”
Fat crystals and water-in-oil emulsion stability
Ghosh, S., & Rousseau, D. (2011) · Current Opinion in Colloid & Interface Science · doi:10.1016/j.cocis.2011.06.006 · Cited by 251
Effects of temperature on water-in-oil emulsions stabilised solely by wax microparticles
Binks, B. P., & Rocher, A. (2009) · Journal of Colloid and Interface Science · doi:10.1016/j.jcis.2009.03.089 · Cited by 188 · cited 1×
“They cause corrosion, scaling, and mechanical changes in gas-oil separation units, affect the operation of the pumping systems due to the elevated viscosity, influence raw material processing quality and increase energy consumption (Binks and Rocher, 2009) .”
Structure of waxy crude oil emulsion gels
Visintin, R. F. G., Lockhart, T. P., Lapasin, R., & D’Antona, P. (2008) · Journal of Non-Newtonian Fluid Mechanics · doi:10.1016/j.jnnfm.2007.07.008 · Cited by 145 · cited 1×
“This network can increase the emulsion stability (Visintin et al. , 2008).”
Chemically Induced Destabilization of Water-in-Crude Oil Emulsions
Peña, A. A., Hirasaki, G. J., & Miller, C. A. (2005) · Industrial & Engineering Chemistry Research · doi:10.1021/ie049666i · Cited by 143 · cited 1×
“A mixture of 200 ppm of polymer polyurethane and 40 ppm of phenolic resin managed to achieve complete water separation in less than 2 hours at 30 °C (Pena et al. , 2005) .”
Dewatering of crude oil emulsions 3. Emulsion resolution by chemical means
Mohammed, R. A., Bailey, A. I., Luckham, P. F., & Taylor, S. E. (1994) · Colloids and Surfaces A: Physicochemical and Engineering Aspects · doi:10.1016/0927-7757(93)02706-k · Cited by 133 · cited 1×
“In term of resin alkoxylate demulsifier application, Mohammed et al. (1994) has evaluated that the ethylene oxide: propylene oxide mixes and resin: alkoxylate ratio are more important for assessing demulsifier performance than the type of resin used.”
Grenoble, Z., & Trabelsi, S. (2018) · Advances in Colloid and Interface Science · doi:10.1016/j.cis.2018.08.003 · Cited by 120 · cited 2×
“Grenoble and Trabelsi, (2018) also supported this theory and mentioned that asphaltenes, which have a more lipo-philic character, require a more hydrophilic demulsifier (oil soluble or less water soluble demulsifier) to shift the hydrophilic lipophilic deviation (HLD) towards zero.”
Chemical Interactions and Demulsifier Characteristics for Enhanced Oil Recovery Applications
Nguyen, D., Sadeghi, N., & Houston, C. (2012) · Energy & Fuels · doi:10.1021/ef201800b · Cited by 90 · cited 2×
“As can be observed from the graph, for the low crude oil API of API 27 and API 34,”
Development of a method for measurement of relative solubility of nonionic surfactants
Wu, J., Xu, Y., Dąbroś, T., & Hamza, H. A. (2003) · Colloids and Surfaces A Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2003.10.028 · Cited by 87
Research works printed but not linked: 1
- [29]29. M. Yimei (2014) "Research on Demulsification Mechanism of Polymer Surfactant Flooding Pro- duced Fluid, " vol. 6, no. 1, pp. 15-21.
Cited by
Controlled operation of a direct contact thermal energy storage device
Thon, H., Simonsen, G., & Leinan, P. R. (2025) · Chemical Engineering Science · doi:10.1016/j.ces.2025.121385 · Cited by 4
Metadata
- Authors
- Halim, N. H., Saaid, I. M., & Panuganti, S. R.
- Affiliations
- PETRONAS Research Sdn Bhd (Malaysia) (MY)
- Universiti Teknologi Petronas (MY)
- Venue
- Substantia
- Publisher
- Firenze University Press
- Published
- 2023-06-19
- ISSN
- 2532-3997 (ISSN-L)
- OpenAlex
- W4381144402
- Cited by
- 1
- References
- 24
- Citations by year
- 2025: 1
- FWCI
- 0.13
- Type
- journal article
- Language
- en
- Open access
- diamond
- dx.doi.org
- Locations
- Substantia (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Topics
- Physical Sciences › Chemistry › Analytical Chemistry › Petroleum Processing and Analysis
- Physical Sciences › Energy › Fuel Technology › Enhanced Oil Recovery Techniques
- Physical Sciences › Chemistry › Physical and Theoretical Chemistry › Surfactants and Colloidal Systems
- Keywords
- demulsifier selection, water-in-oil emulsions, chemical demulsification, emulsion destabilization, enhanced oil recovery, synthetic crude oil, wax content, asphaltene content, Southeast Asia
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.