The DOI matches its Crossref record.
The Effect of Manufacturing Defects on the Fatigue Behaviour of Ti-6Al-4V Specimens Fabricated Using Selective Laser Melting
Open accessAbstract
Additive Manufacturing (AM) technologies are considered revolutionary because they could fundamentally change the way products are designed. Selective Laser Melting (SLM) is a metal based AM process with significant and growing potential for the manufacture of aerospace components. Traditionally a material needs to be listed in the Metallic Materials Properties Development and Standardization (MMPDS) handbook if it is to be considered certified. However, this requires a considerable amount of test data to be generated on the materials mechanical properties. Therefore, the MMPDS certification process does not lend itself easily to the certification of AM components as the final component can have similar mechanical properties to wrought alloys combined with the defects associated with traditional casting and welding technologies. These defects can substantially decrease the fatigue life of a fabricated component. The primary purpose of this investigation was to study the fatigue behaviour of as-built Ti-6Al-4V (Ti64) samples. Fatigue tests were performed on the Ti-6Al-4V specimens built using SLM with a variety of layer thicknesses and build (vertical or horizontal) directions. Fractography revealed the presence of a range of manufacturing defects located at or near the surface of the specimens. The experimental results indicated that Lack-of-Fusion (LOF) defects were primarily responsible for fatigue crack initiation. The reduction in fatigue life appeared to be affected by the location, size and shape of the LOF defect.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Mechanical behavior of additive manufactured, powder-bed laser-fused materials
Mower, T. M., & Long, M. J. (2016) · Materials Science and Engineering: A · doi:10.1016/j.msea.2015.10.068 · Cited by 1,001
Gong, H., Rafi, K., Gu, H., Janaki Ram, G. D., Starr, T., & Stucker, B. (2015) · Materials & Design · doi:10.1016/j.matdes.2015.07.147 · Cited by 940
Defect formation mechanisms in selective laser melting: a review
Zhang, B., Li, Y., & Bai, Q. (2017) · Chinese Journal of Mechanical Engineering · doi:10.1007/s10033-017-0121-5 · Cited by 924
In situ X-ray imaging of defect and molten pool dynamics in laser additive manufacturing
Leung, C. L. A., Marussi, S., Atwood, R. C., Towrie, M., Withers, P. J., & Lee, P. D. (2018) · Nature Communications · doi:10.1038/s41467-018-03734-7 · Cited by 817
Benedetti, M., du Plessis, A., Ritchie, R. O., Dallago, M., Razavi, N., & Berto, F. (2021) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2021.100606 · Cited by 788
Metadata
- Authors
- Liu, Q. C., Elambasseril, J., Sun, S. J., Leary, M., Brandt, M., & Sharp, P. K.
- Venue
- Advanced Materials Research
- Publisher
- Trans Tech Publications, Ltd.
- Published
- 2014-03-12
- Volume
- 891-892
- Pages
- 1519-1524
- ISSN
- 1022-6680 (ISSN-L)
- 1662-8985
- OpenAlex
- W2076916224
- Cited by
- 201
- References
- 0
- FWCI
- 9.74
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: The Effect of Manufacturing Defects on the Fatigue Behaviour of Ti-6Al-4V Specimens Fabricated Using Selective Laser Melting. https://app.cochat.ai/papers/10.4028/www.scientific.net/amr.891-892.1519
- The paper
- Liu, Q. C., Elambasseril, J., Sun, S. J., Leary, M., Brandt, M., & Sharp, P. K. (2014). The Effect of Manufacturing Defects on the Fatigue Behaviour of Ti-6Al-4V Specimens Fabricated Using Selective Laser Melting. Advanced Materials Research. https://doi.org/10.4028/www.scientific.net/amr.891-892.1519
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.