Low-Sensitivity Design of Allpass Based Fractional Delay Digital Filters
Open accessThe DOI matches its Crossref record; 38 of the 39 references it cites were found in a registry or an index; none of the 11 sources its claims cite is checked for support yet.
Abstract
Conventional linear digital circuits are providing usually a delay response that is equal to an integer number of sampling intervals (as in linear-phase FIR (finite-impulse-response) realizations) or is changing uncontrollably with the frequency (for all IIR (infinite-impulseresponse) digital filters). It appeared, however, that we might often need a circuit with a delay response that is a fraction of the sampling interval and is fixed or variable (or only adjustable). Design and implementation of such circuits with given and properly controlled fractional delay (FD) is the hottest digital filters topic in the last ten years. These circuits are invaluable in many telecommunications applications, like time adjustment and precise jitter elimination in digital receivers, echo cancellation, phase-array antenna systems, transmultiplexers, sample-rate converter and software radio. They are needed in speech synthesis and processing, image interpolation, sigma-delta modulators, time-delay estimation, in some biomedical applications and for modeling of musical instruments. Most of these applications are overviewed in (Laakso et al., 1996) and (Valimaki & Laakso, 2001).
Overview
CoChat Summary
TL;DR
This chapter proposes low-sensitivity design of allpass-based fractional delay digital filters by decomposing Thiran allpass transfer functions into first- and second-order sections and selecting or developing sections with minimized phase sensitivity for the actual pole zones. It reports improved fixed and variable FD accuracy under short coefficient wordlengths, including a new IS second-order allpass section for zone 2.
Key findings
- FD allpass poles obtained via Thiran approximation occupy positions atypical for conventional filters; the unit circle is divided into 11 zones, and practical FD poles concentrate in zones 1, 2, 5, and 6, often only in zone 2.
- The new second-order IS section has the lowest worst-case phase sensitivity for small FD values (poles in zone 2); GM2 and MH2B are suitable for zone 6, GM2 and MH2A for zones 1 and 5, while KW2A, KW2B, and ST2A generally cannot be recommended.
- For a fixed 11th-order allpass FD filter with D = 11.2, the best section set (2MH2A+3IS+MH1) gives phase delay 11.195 instead of 11.2 even at 2-bit wordlength; the worst set (2KW2A+2KW2B+IS+SV, WSmax = 669) gives 11.235 at 4-bit CSD and is almost destroyed at 2 bits.
- For variable second-order filters with d = 0.3 and third-order coefficient approximations, the IS structure has higher tuning accuracy than gathering and Cho-Parhi structures; near DC, IS deviations for 3 and 2 bits are −0.002 and −0.0179, versus −0.009/−0.041 for gathering and −0.0086/−0.041 for Cho-Parhi. The RDI method shows higher phase-delay error and loses maximally flat behavior for intermediate D.
Methods
- Design uses Thiran approximation for maximally flat group-delay allpass transfer functions, then decomposes them into first- and second-order sections; low-sensitivity sections are selected or developed according to pole position zones, with worst-case and Schoeffler phase sensitivities evaluated using PANDA.
- For variable FD filters, each transfer-function coefficient is expanded as a Taylor series in the fractional part d and truncated after the linear, quadratic, or cubic term; coefficients are realized as composite multipliers containing fixed and variable multipliers, avoiding a critical path.
- Experiments simulate fixed 11th-order D = 11.2 filters with five section sets under coefficient quantization in CSD code, and second-order variable FD filters for d = 0.3 with I = P = T = 3 comparing gathering, Cho-Parhi, and IS structures; RDI is compared for 4th-order filters with D from 4.1 to 4.5.
Limitations
- The paper states that parasitic noises of fixed-point arithmetic have not been investigated; they are expected to be low because of low sensitivity and central pole positions, but this remains to be verified in future work.
- The paper states that transients in tunable IIR structures are not solved and need more efficient methods in future work.
- The paper notes RDI limitations: complicated circuitry, narrow tuning range, growing tuning error, and no connection to a specific realization so sensitivity cannot be considered; gathering structure drawbacks include many multipliers/adders, long critical paths, and large coefficient spread.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures



















Verification
Claims the paper makes
0 Valid · 2 Not valid · 9 Not checked · 41 Own results and interpretations
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The behavior of the most popular allpass sections when having poles in these zones was investigated and it was shown that the proper selection of the sections is very important when trying to minimize the overall sensitivity.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“A new second-order allpass section, providing low sensitivity for zone 2 (and thus very suitable for high accuracy FD realizations) was developed by the authors.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
In the paper
“We have applied this approach in (Ivanova et al., 2005) and after deriving closed form expressions for the coefficients of the allpass sections given in Sect. 4, we have obtained multiplierless realizations with no more than three adders per coefficient.”
What the sources say
- Not matchedcites Ivanova et al., 2005
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“It is seen that our approach and the ChoParhi method are decreasing considerably the sensitivity, compared to that of the gathering structure, for 0 5 . d”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Because of the lower sensitivity of the IS structure the tuning accuracy is higher than that of the gathering structure and Cho-Parhi structure even when the TF coefficients are quantized to 2 significant bits (in CSD code).”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
12 more claims
Create a free account to see all 52 claims and every source verdict.
- It may state two separate claims as one. 29
- Probably not a substantial claim. 7
- The quote only partly states this claim. 1
Citations
Cites
A continuously variable digital delay element
Farrow, C. W. (2003) · 1988., IEEE International Symposium on Circuits and Systems · doi:10.1109/iscas.1988.15483 · Cited by 816 · cited 1×
“Most of the VFD FIR filters are using the Farrow structure (Farrow, 1988), its modifications (YliKaakinen & Saramaki, 2006) or transformations (Deng, 2009a).”
MethodSplitting the Unit Delay - Tools for fractional delay filter design
Laakso, T. I., Välimäki, V., Karjalainen, M., et al. (1996) · IEEE Signal Processing Magazine · Cited by 534
Recursive digital filters with maximally flat group delay
Thiran, J.-P. (1971) · IEEE Transactions on Circuit Theory · doi:10.1109/tct.1971.1083363 · Cited by 247 · cited 2×
“The third and most popular group of methods is the maximally-flat design of allpass FDFs based on Thiran approximation (Thiran, 1971), giving a closed-form solution for the TF coefficients.”
MethodDesign of 1-D and 2-D variable fractional delay allpass filters using weighted least-squares method
Tseng, C.-C. (2002) · IEEE Transactions on Circuits and Systems I: Fundamental Theory and Applications · doi:10.1109/tcsi.2002.803361 · Cited by 136 · cited 2×
“These methods are further generalized and expanded to FIR, allpass, Hilbert transformers and other devices in (Kwan & Jiang, 2009); (Pei et al., 2010).”
MethodOn the design of adjustable fractional delay fir filters
Johansson, H., & Lowenborg, P. (2003) · IEEE Transactions on Circuits and Systems II: Analog and Digital Signal Processing · doi:10.1109/tcsii.2003.809712 · Cited by 121
SVD-Based Design and New Structures for Variable Fractional-Delay Digital Filters
Deng, T.-B., & Nakagawa, Y. (2004) · IEEE Transactions on Signal Processing · doi:10.1109/tsp.2004.831922 · Cited by 110 · cited 3×
“…many other VFD FIR filters design methods like a constrained minimax optimization method (Vesma & Saramaki, 2000), a singular value decomposition method (Deng & Nakagawa, 2004), a Taylor series expansion method (Johanson & Lovenborg, 2003), and the WLS design (Tseng, 2004); (Huang et al., 2009).”
BackgroundMethodNoniterative WLS design of allpass variable fractional-delay digital filters
Deng, T. (2006) · IEEE Transactions on Circuits and Systems I Fundamental Theory and Applications · doi:10.1109/tcsi.2005.854406 · Cited by 110 · cited 4×
“These methods are further generalized and expanded to FIR, allpass, Hilbert transformers and other devices in (Kwan & Jiang, 2009); (Pei et al., 2010).”
MethodInfluentialMinimax Design of Low-Complexity Allpass Variable Fractional-Delay Digital Filters
Deng, T.-B. (2010) · IEEE Transactions on Circuits and Systems I: Regular Papers · doi:10.1109/tcsi.2009.2037407 · Cited by 70 · cited 3×
“In (Deng, 2010a) several new hybrid structures with reduced complexity have been developed.”
BackgroundMethodHybrid Structures for Low-Complexity Variable Fractional-Delay FIR Filters
Deng, T.-B. (2010) · IEEE Transactions on Circuits and Systems I: Regular Papers · doi:10.1109/tcsi.2009.2025848 · Cited by 60 · cited 3×
“In (Deng, 2010a) several new hybrid structures with reduced complexity have been developed.”
BackgroundMethodGeneralized WLS Method for Designing All-Pass Variable Fractional-Delay Digital Filters
Deng, T. (2009) · IEEE Transactions on Circuits and Systems I Regular Papers · doi:10.1109/tcsi.2009.2015213 · Cited by 55 · cited 3×
“Most of the VFD FIR filters are using the Farrow structure (Farrow, 1988), its modifications (YliKaakinen & Saramaki, 2006) or transformations (Deng, 2009a).”
MethodEfficient tunable IIR and allpass filter structures
Makundi, M., Laakso, T. I., & Välimäki, V. (2001) · Electronics Letters · doi:10.1049/el:20010276 · Cited by 53 · cited 3×
“In (Makundi et al., 2001) the coefficients (1) have been presented as: ,,,ˆ)()()( )( )( )( )(ˆ NkfordenNdnd k N nNd nNd nd k N a N l l lk k n N Nkn k N n k n k nk k 211 1 1 1 0 1 11 1 0”
MethodWLS Design of Variable Fractional-Delay FIR Filters Using Coefficient Relationship
Huang, Y.-D., Pei, S., & Shyu, J.-J. (2009) · IEEE Transactions on Circuits & Systems II Express Briefs · doi:10.1109/tcsii.2008.2011598 · Cited by 49 · cited 2×
“…many other VFD FIR filters design methods like a constrained minimax optimization method (Vesma & Saramaki, 2000), a singular value decomposition method (Deng & Nakagawa, 2004), a Taylor series expansion method (Johanson & Lovenborg, 2003), and the WLS design (Tseng, 2004); (Huang et al., 2009).”
BackgroundMethodFIR, Allpass, and IIR Variable Fractional Delay Digital Filter Design
Kwan, H. K., & Jiang, A. (2009) · IEEE Transactions on Circuits and Systems I Regular Papers · doi:10.1109/tcsi.2008.2011590 · Cited by 48 · cited 2×
“These methods are further generalized and expanded to FIR, allpass, Hilbert transformers and other devices in (Kwan & Jiang, 2009); (Pei et al., 2010).”
MethodValimaki, V., & Laakso, T. I. (1998) · IEEE Transactions on Signal Processing · doi:10.1109/78.735314 · Cited by 45 · cited 1×
“Suppression of these transients is a difficult problem, several methods to solve it are discussed in (Valimaki & Laakso, 1998); (Valimaki & Laakso, 2001); (Makundi et al., 2002) and (Hachabiboĝlu et al., 2007), but publications on this topic are very few and a lot more remains to be done.”
MethodDesign and properties of polynomial-based fractional delay filters
Vesma, J., & Saramaki, T. (2002) · 2000 IEEE International Symposium on Circuits and Systems. Emerging Technologies for the 21st Century. Proceedings (IEEE Cat No.00CH36353) · doi:10.1109/iscas.2000.857037 · Cited by 44 · cited 1×
“There are many other VFD FIR filters design methods like a constrained minimax optimization method (Vesma & Saramaki, 2000), a singular value decomposition method (Deng & Nakagawa, 2004), a Taylor series expansion method (Johanson & Lovenborg, 2003), and the WLS design (Tseng, 2004); (Huang et al.,…”
MethodRobust Structure Transformation for Causal Lagrange-Type Variable Fractional-Delay Filters
Deng, T. (2008) · IEEE Transactions on Circuits and Systems I Regular Papers · doi:10.1109/tcsi.2008.2008277 · Cited by 38 · cited 4×
“Most of the VFD FIR filters are using the Farrow structure (Farrow, 1988), its modifications (YliKaakinen & Saramaki, 2006) or transformations (Deng, 2009a).”
BackgroundMethodInfluentialMultiplication-Free Polynomial-Based FIR Filters with an Adjustable Fractional Delay
Yli‐Kaakinen, J., & Saramäki, T. (2006) · Circuits Systems and Signal Processing · doi:10.1007/s00034-005-2507-3 · Cited by 33
Fractional Delay Filters—Design and Applications
Välimäki, V., & Laakso, T. I. (2001) · Information Technology: Transmission, Processing, and Storage · doi:10.1007/978-1-4615-1229-5_20 · Cited by 32 · cited 9×
“Suppression of these transients is a difficult problem, several methods to solve it are discussed in (Valimaki & Laakso, 1998); (Valimaki & Laakso, 2001); (Makundi et al., 2002) and (Hachabiboĝlu et al., 2007), but publications on this topic are very few and a lot more remains to be done.”
BackgroundMethodInfluentialAn algorithm for the optimization of adjustable fractional-delay all-pass filters
Yli‐Kaakinen, J., & Saramäki, T. (2004) · IEEE International Symposium on Circuits and Systems proceedings · doi:10.1109/iscas.2004.1328706 · Cited by 30 · cited 1×
“An improved optimization method was proposed in (Yli-Kaakinen & Saramaki, 2004) to overcome the problems with the convergence when designing VFDFs.”
MethodA New Method for Designing Causal Stable IIR Variable Fractional Delay Digital Filters
Tsui, K. M., Chan, S. C., & Kwan, H. K. (2007) · IEEE Transactions on Circuits & Systems II Express Briefs · doi:10.1109/tcsii.2007.903784 · Cited by 26 · cited 1×
“The method in (Tsui et al., 2007) is based on a new model reduction technique and is applicable to IIR TFs that are decomposable to sub-filters with a common denominator (which will stay fixed when the filter is tuned), realized then as Farrow structures.”
MethodDesign of 1-D Stable Variable Fractional Delay IIR Filters
Zhao, H., & Kwan, H. K. (2007) · IEEE Transactions on Circuits and Systems II: Express Briefs · doi:10.1109/tcsii.2006.882802 · Cited by 24 · cited 3×
“Both methods are achieving an impressive FD variability, but at a price of too higher TF order (30 or 55 in (Zhao & Kwan, 2007)) and calculation of too many multiplier coefficients (for example 426 in (Zhao & Kwan, 2007)), to be practical.”
BackgroundMethodInfluentialA New Criterion for the Design of Variable Fractional-Delay FIR Digital Filters
Shyu, J.-J., Pei, S., Chan, C.-H., Huang, Y.-D., & Lin, S.-H. (2009) · IEEE Transactions on Circuits and Systems I Regular Papers · doi:10.1109/tcsi.2009.2023835 · Cited by 23 · cited 3×
“Recently a new method (Tseng & Lee, 2009) 7 www.intechopen.com and a new criterion (Shyu et al., 2010) for design of such filters have been proposed.”
BackgroundMethodPei, S., Wang, P., & Lin, C.-H. (2009) · IEEE Transactions on Circuits and Systems I Regular Papers · doi:10.1109/tcsi.2009.2027806 · Cited by 20 · cited 2×
“These methods are further generalized and expanded to FIR, allpass, Hilbert transformers and other devices in (Kwan & Jiang, 2009); (Pei et al., 2010).”
MethodDesign of a Sample-Rate Converter From CD to DAT Using Fractional Delay Allpass Filter
Cho, K.-J., Park, J.-S., Kim, B.-K., Chung, J.-G., & Parhi, K. K. (2007) · IEEE Transactions on Circuits and Systems II: Express Briefs · doi:10.1109/tcsii.2006.885067 · Cited by 15 · cited 4×
“This structure was criticized recently for its long critical path and big difference between the coefficient values (requiring longer wordlength) and an improved structure was proposed in (Cho et al., 2007).”
BackgroundMethodInfluentialImproved tuning accuracy design of parallel-allpass-structures-based variable digital filters
Stoyanov, G. K., & Kawamata, A. (1998) · IEEE International Symposium on Circuits and Systems proceedings · doi:10.1109/iscas.1998.694502 · Cited by 14 · cited 1×
“5 and developed or discussed (together with many other sections with similar sensitivities) in (Topalov & Stoyanov, 1991); (Stoyanov & Nishihara, 1995); (Stoyanov & Kawamata, 1998); (Stoyanov & Kawamata, 2003); (Stoyanov et al., 2005) and in the references there-in.”
BackgroundSelf-citationAnalysis of Root Displacement Interpolation Method for Tunable Allpass Fractional-Delay Filters
Hacihabiboglu, H., Gunel, B., & Kondoz, A. M. (2007) · IEEE Transactions on Signal Processing · doi:10.1109/tsp.2007.897916 · Cited by 12 · cited 9×
“The denominator of (2) (the denominators of the two initial allpass transfer functions) is represented as (Hachabiboĝlu et al., 2007):”
BackgroundMethodInfluentialA Comparative Study of First-Order Digital Allpass Filter Sections
Stoyanov, G. K., & Clausert, H. (1994) · Frequenz · doi:10.1515/freq.1994.48.9-10.221 · Cited by 12 · cited 1×
“About 20 such sections, including several newly developed, have been investigated and compared in (Stoyanov & Clausert, 1994) and it was shown that several low-sensitivity sections for every real poleposition could be found.”
BackgroundSelf-citationDesign and Realization of Efficient IIR Digital Filter Structures Based on Sensitivity Minimizations
Stoyanov, G. K., Nikolova, Z., Ivanova, K., & Anzova, V. I. (2007) · International Conference on Telecommunication in Modern Satellite, Cable and Broadcasting Services · doi:10.1109/telsks.2007.4375998 · Cited by 11 · cited 2×
“The strategy to achieve our aim is based on our approach, described in (Stoyanov et al., 2007) and using (when possible) a cascade realization of the allpass TF.”
BackgroundMethodSelf-citationAsynchronous implementation of transient suppression in tunable IIR filters
Makundi, M., Laakso, T. I., & Liu, Y. (2003) · IEEE International Conference on Digital Signal Processing (DSP) · doi:10.1109/icdsp.2002.1028215 · Cited by 10 · cited 2×
“The interest in general IIR VFD realizations, will grow, however, because they may offer a lower overall group delay time compared to the allpass realizations (Kwan & Jiang, 2009) and also could be used for a simultaneous magnitude and phase approximation.”
MethodDesign of variable fractional delay FIR filter using symmetry
Tseng, C. (2004) · IEEE International Symposium on Circuits and Systems proceedings · doi:10.1109/iscas.2004.1328787 · Cited by 9
High Tuning Accuracy Design of Variable IIR Filters as a Cascade of Identical Sub-Filters
Stoyanov, G. K., Uzunov, I. M., & Kawamata, M. (2005) · IEEE International Symposium on Circuits and Systems proceedings · doi:10.1109/iscas.2005.1465440 · Cited by 7 · cited 2×
“5 and developed or discussed (together with many other sections with similar sensitivities) in (Topalov & Stoyanov, 1991); (Stoyanov & Nishihara, 1995); (Stoyanov & Kawamata, 1998); (Stoyanov & Kawamata, 2003); (Stoyanov et al., 2005) and in the references there-in.”
BackgroundSelf-citationSloyanov, G., & Kawamata, M. (2003) · doi:10.1109/iscas.2003.1205082 · Cited by 6
Cascaded Multiplierless Realizations of Low Sensitivities Allpass based Fractional Delay Filters
Ivanova, K. S., Anzova, V. I., & Stoyanov, G. K. (2006) · TELSIKS 2005 - 2005 uth International Conference on Telecommunication in ModernSatellite, Cable and Broadcasting Services · doi:10.1109/telsks.2005.1572074 · Cited by 5 · cited 1×
“We have applied this approach in (Ivanova et al., 2005) and after deriving closed form expressions for the coefficients of the allpass sections given in Sect.”
MethodSelf-citationNon-iterative WLS Design of Allpass Variable Fractional-Delay Digital Filters
Deng, T. (2005) · IEEE International Symposium on Circuits and Systems proceedings · doi:10.1109/iscas.2005.1464635 · Cited by 5
Closed-Form Design Of Variable Fractional Delay Filter Using Discrete Fourier Transform
Lee, S., & Tseng, C. (2009) · Zenodo (CERN European Organization for Nuclear Research) · doi:10.5281/zenodo.41431 · Cited by 4
A New Low-sensitivity Second-order Allpass Section Suitable for Fractional Delay Filter Realizations
Ivanova, K., & Stoyanov, G. K. (2007) · International Conference on Telecommunication in Modern Satellite, Cable and Broadcasting Services · doi:10.1109/telsks.2007.4376001 · Cited by 3 · cited 1×
“We have developed in (Ivanova & Stoyanov, 2007); (Nikolova et al., 2009) a new section, shown in Fig.”
MethodSelf-citationLow-sensitivity design and implementation of allpass based fractional delay digital filters
Nikolova, K. S., Stoyanov, G. K., & Kawamata, M. (2009) · European Conference on Circuit Theory and Design · doi:10.1109/ecctd.2009.5275050 · Cited by 2 · cited 2×
“The sensitivities of the realizations are strongly depending on the position of their TF poles in the z-plane, so it is important to know how the poles of the allpass-based FD filters are situated there.”
BackgroundMethodSelf-citationStoyanov, G. K., Nikolova, K. S., & Markova, V. I. (2009) · 2009 9th International Conference on Telecommunication in Modern Satellite, Cable, and Broadcasting Services · doi:10.1109/telsks.2009.5339430 · Cited by 1 · cited 1×
“A further improvement of the multiplierless design was achieved in (Stoyanov et al., 2009) by applying a genetic algorithm to optimize the values of the coefficients within the set of possible values limited by the quantization.”
MethodSelf-citation
Research works printed but not linked: 6
- Nikolova, K. & Stoyanov, G. (2008). 'А new method of design of variable fractional delay digital allpass filters', Proc. 43 th Intern. Conference ICEST' 2008, Nish, Serbia, vol. 1, pp. 75- 8, June 25-27, 2008.
- Nishihara, A. (1984). 'Low-sensitivity second-order digital filters - analysis and design in terms of frequency sensitivity', Trans. IECE of Japan , vol. E 67, No 8, pp. 433-439, Aug. 1984.
- Stoyanov, G. & Nishihara, A. (1995). 'Very low sensitivity design of digital IIR filters using parallel and cascade-parallel connections of allpass sections', Bulletin of INCOCSAT , Tokyo Institute of Technology, vol. 1, pp. 55-64, March 1995.
- Sugino, N. & Nishihara, A. (1990). 'Frequency-domain simulator of digital networks from the structural description', Trans. IECE of Japan , vol. E 73, No.11, pp. 1804-1806, Nov. 1990.
- Topalov, I. & Stoyanov, G. (1991). 'A systematic approach to the design of low-sensitivity limit-cycle-free universal bilinear and biquadratic digital filter sections', Proc. 10 th European Conf. on Circuit Theory and Design ( ECCTD '91), Copenhagen, Denmark, vol. 1, pp. 213-222, Sept. 02-06, 1991.
- Vesma, J. & Saramaki, T. (2000). 'Design and properties of polynomial-based fractionaldelay filters', Proc. ISCAS' 2000, Geneva, Switzerland, vol. 1, pp. 104-107, May 2000.
Cited by
A Simple Ladder Realization of Maximally Flat Allpass Fractional Delay Filters
Koshita, S., Abe, M., & Kawamata, M. (2014) · IEEE Transactions on Circuits and Systems II: Express Briefs · doi:10.1109/tcsii.2013.2296131 · Cited by 5
“This design method was extended to the synthesis of variable fractional delay filters [3]–[6], [10].”
MethodImproved accuracy and low-sensitivity design of digital allpass based hilbert transformers
Stoyanov, G. K., & Nikolova, K. S. (2013) · International Conference on Telecommunications in Modern Satellite, Cable and Broadcasting Services (TELSIKS) · doi:10.1109/telsks.2013.6704892 · Cited by 3
“The sensitivities of the second-order allpass sections introduced in Section 3B have been extensively investigated and compared in the literature [19], [21], [26] and will not be treated here.”
BackgroundMethodInfluentialSelf-citationDesign of IIR Multiple-Notch Filters with Symmetric Magnitude Responses About Notch Frequencies
Krstić, I. B., Nikolić, S. V., Stančić, G., et al. (2018) · Circuits Systems and Signal Processing · doi:10.1007/s00034-018-0841-5 · Cited by 3
Accuracy improvement of real-poles allpass-based digital Hilbert transformers
Nikolova, K. S., & Stoyanov, G. K. (2014) · International Journal of Reasoning-based Intelligent Systems · doi:10.1504/ijris.2014.063947 · Cited by 1
“We developed several special sections starting from the real first order sections studied and cited in Stoyanov and Clausert (1994) and Stoyanov et al. (2007, 2011) by changing the signs of the coefficients of the allpass TFs in equation (4) and by replacing z–1 by z–2 in the allpass structures as…”
BackgroundMethodSelf-citationInvestigating the sensitivity of first-order recursive DSP networks
Nikolova, K. S., & Valkova-Jarvis, Z. (2016) · IEEE International Black Sea Conference on Communications and Networking · doi:10.1109/blackseacom.2016.7901601
“An interesting observation is that, in the case of zero frequency, MHNS and LS1a networks behave identically but are inferior to the LS1b structure.”
BackgroundSelf-citation
Metadata
- Authors
- Stoyanov, G., Nikolova, K., & Kawamat, M.
- Affiliations
- Technical University of Sofia (BG)
- Tohoku University (JP)
- ORCID
- Stoyanov, G.
- Venue
- Digital Filters
- Publisher
- InTech
- Published
- 2011-04-11
- OpenAlex
- W1579385901
- Cited by
- 5
- References
- 39
- Citations by year
- 2018: 1 · 2016: 1 · 2014: 2 · 2013: 1
- FWCI
- 3.48
- Type
- book chapter
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- cc-by-nc-sa
- Locations
- InTech eBooks (publishedVersion, cc-by-nc-sa)
- BiblioBoard Library Catalog (Open Research Library) (submittedVersion, cc-by-sa)
- Contact-less Assessment of In-vivo Body Signals Using Microwave Doppler Radar (InTech) (submittedVersion, cc-by-nc-sa)
- Funders
- Bulgarian National Science Fund
- Technical University of Sofia
- Topics
- Physical Sciences › Computer Science › Signal Processing › Digital Filter Design and Implementation
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Analog and Mixed-Signal Circuit Design
- Physical Sciences › Computer Science › Signal Processing › Advanced Adaptive Filtering Techniques
- Keywords
- fractional delay filter, all-pass filter, digital filter design, variable delay, sampling rate conversion, transmultiplexer, echo cancellation, phased array antenna, time delay estimation
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.