The DOI matches its Crossref record; 12 of the 12 references it cites were found in a registry or an index.
Surface Modification of Ti6Al4V Open Porous Structures Produced by Additive Manufacturing
Abstract
Additive manufacturing techniques can be used to produce micro‐porous structures with global morphological properties that are highly controlled through robust computer design. Despite these advantages, most of these techniques still hold several functional constraints, resulting from present technical device limits and consequently the inability to control surface morphology at a microscale level. In this study, a novel protocol for surface modification of 3D titanium alloy‐based open porous structures is developed, which applies a combination of chemical etching (CHE) and electrochemical polishing (ECP) using HF‐based solutions. This protocol achieves significant and controllable roughness reduction of additive manufactured 3D Ti6Al4V open porous structures. Chemical etching mainly removes the attached powder grains, while ECP further decreases the roughness. In this way the heterogeneity of the strut surface roughness throughout the full 3D structure is effectively removed.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Porous scaffold design for tissue engineering
Hollister, S. J. (2005) · Nature Materials · doi:10.1038/nmat1421 · Cited by 3,969
Surface modification of titanium, titanium alloys, and related materials for biomedical applications
LIU, X., CHU, P., & DING, C. (2004) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2004.11.001 · Cited by 3,487
Spectral Analysis for Physical Applications
Percival, D. B., & Walden, A. T. (1993) · Cambridge University Press eBooks · doi:10.1017/cbo9780511622762 · Cited by 2,161
Consolidation phenomena in laser and powder-bed based layered manufacturing
Kruth, J.-P., Levy, G., Klocke, F., & Childs, T. H. C. (2007) · CIRP Annals · doi:10.1016/j.cirp.2007.10.004 · Cited by 1,444
Spectral Analysis for Physical Applications: Multitaper and Conventional Univariate Techniques.
DSS, Percival, D. B., & Walden, A. T. (1997) · Journal of the American Statistical Association · doi:10.2307/2965609 · Cited by 955
Woodfield, T. B. F., Malda, J., de Wijn, J., Péters, F., Riesle, J., & van Blitterswijk, C. A. (2004) · Biomaterials · doi:10.1016/j.biomaterials.2003.10.056 · Cited by 618
Manufacture by selective laser melting and mechanical behavior of a biomedical Ti–24Nb–4Zr–8Sn alloy
Zhang, L., Klemm, D., Eckert, J., Hao, Y., & Sercombe, T. B. (2011) · Scripta Materialia · doi:10.1016/j.scriptamat.2011.03.024 · Cited by 597
Microstructure and mechanical properties of Selective Laser Melted 18Ni-300 steel
Kempen, K., Yasa, E., Thijs, L., Kruth, J.-P., & Van Humbeeck, J. (2011) · Physics Procedia · doi:10.1016/j.phpro.2011.03.033 · Cited by 566
Van Bael, S., Kerckhofs, G., Moesen, M., Pyka, G., Schrooten, J., & Kruth, J. P. (2011) · Materials Science and Engineering: A · doi:10.1016/j.msea.2011.06.045 · Cited by 452
Self-citationManufacturing by combining Selective Laser Melting and Selective Laser Erosion/laser re-melting
Yasa, E., Kruth, J.-P., & Deckers, J. (2011) · CIRP Annals · doi:10.1016/j.cirp.2011.03.063 · Cited by 265
Cited by
Arabnejad, S., Burnett Johnston, R., Pura, J. A., Singh, B., Tanzer, M., & Pasini, D. (2016) · Acta Biomaterialia · doi:10.1016/j.actbio.2015.10.048 · Cited by 578
Surface post-treatments for metal additive manufacturing: Progress, challenges, and opportunities
Maleki, E., Bagherifard, S., Bandini, M., & Guagliano, M. (2021) · Additive Manufacturing · doi:10.1016/j.addma.2020.101619 · Cited by 528
X-ray computed tomography for additive manufacturing: a review
Thompson, A., Maskery, I., & Leach, R. K. (2016) · Measurement Science and Technology · doi:10.1088/0957-0233/27/7/072001 · Cited by 521
Fox, J. C., Moylan, S. P., & Lane, B. M. (2016) · Procedia CIRP · doi:10.1016/j.procir.2016.02.347 · Cited by 377
Microstructure and mechanical behavior of porous Ti–6Al–4V parts obtained by selective laser melting
Sallica-Leva, E., Jardini, A. L., & Fogagnolo, J. B. (2013) · Journal of the Mechanical Behavior of Biomedical Materials · doi:10.1016/j.jmbbm.2013.05.011 · Cited by 340
Metadata
- Authors
- Pyka, G., Burakowski, A., Kerckhofs, G., Moesen, M., Van Bael, S., Schrooten, J., & Wevers, M.
- Venue
- Advanced Engineering Materials
- Publisher
- Wiley
- Published
- 2012-04-17
- Volume
- 14
- Issue
- 6
- Pages
- 363-370
- ISSN
- 1438-1656 (ISSN-L)
- 1527-2648
- OpenAlex
- W2114973216
- Cited by
- 309
- References
- 12
- FWCI
- 16.17
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Surface Modification of Ti6Al4V Open Porous Structures Produced by Additive Manufacturing. https://app.cochat.ai/papers/10.1002/adem.201100344
- The paper
- Pyka, G., Burakowski, A., Kerckhofs, G., Moesen, M., Van Bael, S., Schrooten, J., & Wevers, M. (2012). Surface Modification of Ti6Al4V Open Porous Structures Produced by Additive Manufacturing. Advanced Engineering Materials. https://doi.org/10.1002/adem.201100344
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.
