Unexpected Performance of Inkjet-Printed Membrane Electrode Assemblies for Proton Exchange Membrane Fuel Cells
The DOI matches its Crossref record; 25 of the 25 references it cites were found in a registry or an index.
Abstract
The effect of the deposition substrate on the performance of inkjet‐printed membrane electrode assemblies (MEAs) is investigated. MEAs are fabricated from inkjet‐printed catalyst‐coated membranes (CCMs), gas diffusion electrodes (GDEs), and a bilateral sandwich of a CCM and a GDE. All MEAs are tested in proton exchange membrane fuel cells (PEMFCs). When a hot‐pressing step is included in the MEA construction, the power density achieved with the GDE‐based MEA is 1.067 W cm−2, exceeding that achieved with the CCM‐based MEA (0.579 W cm−2), and the bilateral sandwich MEA (0.792 W cm−2). The origin of the superior performance of the inkjet‐printed GDE‐based MEAs is investigated through electrochemical impedance spectroscopy and analysis of the microstructure of the printed membranes and electrodes. Atomic force microscopy and energy dispersive X‐ray spectroscopy suggest that the greater surface and interfacial areas of the GDE‐printed catalyst layer may drive the unexpectedly high performance of the GDE‐based MEA as compared with its CCM and bilateral sandwich counterparts. These results provide new insights into the connections between the substrate, inkjet‐printed catalyst layer microstructure, and catalyst utilization.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“only a few cases exhibit a nearly Newtonian behavior for shear rate of about 1~1000 s -1 [53,75].”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [75]
In the citing paper
“The CCM-based MEAs exhibit a superior performance in some studies due to excellent interfacial contact between the CL and membrane [167], while the GDE-based MEAs perform better in others [75].”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [75]
In the citing paper
“They have different surface structures, e.g., roughness [75], and properties, e.g., contact angle [164], friction coefficient [164], or wetting and permeation of solvent, which influence not only the requirements on catalyst ink, selection of deposition technique, or drying conditions, but also the interface between the CL and membrane or the CL and GDL, as well as the production scale.”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [75]
In the citing paper
“Although the surface of the decal substrate is similar to the membrane, the CL surface facing the membrane is still uneven but has a lower roughness than that produced by the GDE method [75].”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [75]
In the citing paper
“The MPL has a higher origin surface roughness than the membrane (Figure 11(a1,b1)) [75].”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [75]
Citations
Cites
What are batteries, fuel cells, and supercapacitors?
Winter, M., & Brodd, R. J. (2004) · Chemical Reviews · doi:10.1021/cr020730k · Cited by 7,389
A review on non-precious metal electrocatalysts for PEM fuel cells
Chen, Z., Higgins, D., Yu, A., Zhang, L., & Zhang, J. (2011) · Energy & Environmental Science · doi:10.1039/c0ee00558d · Cited by 1,832
Banham, D., Ye, S., Pei, K., Ozaki, J.-I., Kishimoto, T., & Imashiro, Y. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.03.047 · Cited by 539
3D printed functional nanomaterials for electrochemical energy storage
Zhu, C., Liu, T., Qian, F., Chen, W., Chandrasekaran, S., Yao, B., Song, Y., Duoss, E. B., Kuntz, J. D., Spadaccini, C. M., et al. (2017) · Nano Today · doi:10.1016/j.nantod.2017.06.007 · Cited by 394
Ruiz-Morales, J. C., Tarancón, A., Canales-Vázquez, J., Méndez-Ramos, J., Hernández-Afonso, L., Acosta-Mora, P., Marín Rueda, J. R., & Fernández-González, R. (2017) · Energy & Environmental Science · doi:10.1039/c6ee03526d · Cited by 299
Kim, K.-H., Lee, K.-Y., Kim, H.-J., Cho, E., Lee, S.-Y., Lim, T.-H., Yoon, S. P., Hwang, I. C., & Jang, J. H. (2010) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2009.11.058 · Cited by 212
Inkjet printing of carbon supported platinum 3-D catalyst layers for use in fuel cells
Taylor, A. D., Kim, E. Y., Humes, V. P., Kizuka, J., & Thompson, L. T. (2007) · Journal of Power Sources · doi:10.1016/j.jpowsour.2007.01.024 · Cited by 186
Inkjet and Aerosol Jet Printing of Electrochemical Devices for Energy Conversion and Storage
Deiner, L. J., & Reitz, T. L. (2017) · Advanced Engineering Materials · doi:10.1002/adem.201600878 · Cited by 166
Self-citationDiffusion in Porous Media: Phenomena and Mechanisms
Tartakovsky, D. M., & Dentz, M. (2019) · Transport in Porous Media · doi:10.1007/s11242-019-01262-6 · Cited by 150
Impact of manufacturing processes on proton exchange membrane fuel cell performance
Shahgaldi, S., Alaefour, I., & Li, X. (2018) · Applied Energy · doi:10.1016/j.apenergy.2018.05.086 · Cited by 138
Cited by
The Controllable Design of Catalyst Inks to Enhance PEMFC Performance: A Review
Guo, Y., Pan, F., Chen, W., Ding, Z., Yang, D., Li, B., Ming, P., & Zhang, C. (2021) · Electrochemical Energy Reviews · doi:10.1007/s41918-020-00083-2 · Cited by 175
“These techniques include ultrasonic spraying [13, 227], electrospray deposition [14, 228], electrospinning [229, 230], slot dies [16], inkjet printing [17, 231], doctor blades [18], screen printing [19], brush printing [20, 232] and gravure [21], each with distinct advantages and disadvantages.”
BackgroundMethodFouzaï, I., Gentil, S., Bassetto, V. C., Silva, W. O., Maher, R., & Girault, H. H. (2021) · Journal of Materials Chemistry A · doi:10.1039/d0ta07470e · Cited by 102
Liu, H., Ney, L., Zamel, N., & Li, X. (2022) · Applied Sciences · doi:10.3390/app12083776 · Cited by 85
“The CCM-based MEAs exhibit a superior performance in some studies due to excellent interfacial contact between the CL and membrane [167], while the GDE-based MEAs perform better in others [75].”
BackgroundInfluentialGuo, Y., Yang, D., Li, B., Yang, D., Ming, P., & Zhang, C. (2021) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.1c07070 · Cited by 65
Metadata
- Authors
- Gomes Bezerra, C. A., Deiner, L. J., & Tremiliosi-Filho, G.
- Affiliations
- Instituto de Química de São Carlos, USP Av. Trab. São Carlense, 400 Parque Arnold Schimidt São Carlos SP 13566-590 Brazil
- City University of New York (US)
- Corresponding author
- Deiner, L. Jay
- ORCID
- Deiner, L. Jay
- Venue
- Advanced Engineering Materials
- Publisher
- Wiley
- Published
- 2019-09-12
- Volume
- 21
- Issue
- 11
- ISSN
- 1438-1656 (ISSN-L)
- 1527-2648
- OpenAlex
- W2969756596
- Cited by
- 43
- References
- 25
- Citations by year
- 2025: 7 · 2024: 9 · 2023: 9 · 2022: 7 · 2021: 8 · 2020: 3
- FWCI
- 1.62
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Advanced Engineering Materials (publishedVersion)
- Funders
- Fundação de Amparo à Pesquisa do Estado de São Paulo (2013/16930-7, 2018/08802-2)
- Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (001)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Fuel Cells and Related Materials
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Electrocatalysts for Energy Conversion
- Physical Sciences › Materials Science › Materials Chemistry › Advancements in Solid Oxide Fuel Cells
- Keywords
- inkjet printing, membrane electrode assembly, proton exchange membrane fuel cells, gas diffusion electrode, catalyst coated membranes, hot pressing, catalyst layer microstructure, interfacial area, catalyst utilization, power density
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Unexpected Performance of Inkjet-Printed Membrane Electrode Assemblies for Proton Exchange Membrane Fuel Cells. https://app.cochat.ai/papers/10.1002/adem.201900703
- The paper
- Gomes Bezerra, C. A., Deiner, L. J., & Tremiliosi-Filho, G. (2019). Unexpected Performance of Inkjet-Printed Membrane Electrode Assemblies for Proton Exchange Membrane Fuel Cells. Advanced Engineering Materials. https://doi.org/10.1002/adem.201900703
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.