The DOI matches its Crossref record.
Resorbable Dicalcium Phosphate Bone Substitutes Prepared by 3D Powder Printing
Abstract
Bioceramic bone substitutes with programmed architecture were manufactured at room temperature in this study using a novel 3D printing process that combined 3D powder printing with calcium phosphate cement chemistry. During printing, biphasic α/β‐tricalcium phosphate (Ca 3(PO 4)2, TCP) powder reacted with a liquid component consisting of phosphoric acid solution to form a matrix of dicalcium phosphate dihydrate (CaHPO 4·H 2 O, DCPD, brushite) and unreacted TCP. Printed samples showed compressive strengths between 0.9–8.7 MPa after printing depending on the acid concentration. A further strength improvement to a maximum of 22 MPa could be obtained by additional hardening of the samples in phosphoric acid for three one minute washes. After this treatment, the samples mainly consisted of brushite with minor phases of unreacted TCP and a lesser amount of dicalcium phosphate anhydrate (CaHPO 4, DCPA, monetite). Hydrothermal conversion of brushite to DCPA resulted in an increase of porosity of approximately 13 % and a decrease of strength to 15 MPa, however the resorption rate in vivo was increased as demonstrated after intramuscular implantation over 56 weeks. Major advantages compared with commonly used sintering techniques are the low processing temperature, which enables the fabrication of thermally instable and degradable matrices of secondary calcium phosphates.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Evaluation of 3D Printing and Its Potential Impact on Biotechnology and the Chemical Sciences
Gross, B. C., Erkal, J. L., Lockwood, S. Y., Chen, C., & Spence, D. M. (2014) · Analytical Chemistry · doi:10.1021/ac403397r · Cited by 1,746
3D printing of composite calcium phosphate and collagen scaffolds for bone regeneration
Inzana, J. A., Olvera, D., Fuller, S. M., Kelly, J. P., Graeve, O. A., Schwarz, E. M., Kates, S. L., & Awad, H. A. (2014) · Biomaterials · doi:10.1016/j.biomaterials.2014.01.064 · Cited by 840
Designing Biomaterials for 3D Printing
Guvendiren, M., Molde, J., Soares, R. M. D., & Kohn, J. (2016) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.6b00121 · Cited by 732
How smart do biomaterials need to be? A translational science and clinical point of view
Holzapfel, B. M., Reichert, J. C., Schantz, J.-T., Gbureck, U., Rackwitz, L., Nöth, U., Jakob, F., Rudert, M., Groll, J., & Hutmacher, D. W. (2013) · Advanced Drug Delivery Reviews · doi:10.1016/j.addr.2012.07.009 · Cited by 552
Self-citationBiodegradable Materials and Metallic Implants—A Review
Prakasam, M., Locs, J., Salma-Ancane, K., Loca, D., Largeteau, A., & Berzina-Cimdina, L. (2017) · Journal of Functional Biomaterials · doi:10.3390/jfb8040044 · Cited by 493
Metadata
- Authors
- Gbureck, U., Hölzel, T., Klammert, U., Würzler, K., Müller, F. A., & Barralet, J. E.
- Venue
- Advanced Functional Materials
- Publisher
- Wiley
- Published
- 2007-11-28
- Volume
- 17
- Issue
- 18
- Pages
- 3940-3945
- ISSN
- 1616-301X (ISSN-L)
- 1616-3028
- OpenAlex
- W2117315764
- Cited by
- 233
- References
- 0
- FWCI
- 5.49
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Resorbable Dicalcium Phosphate Bone Substitutes Prepared by 3D Powder Printing. https://app.cochat.ai/papers/10.1002/adfm.200700019
- The paper
- Gbureck, U., Hölzel, T., Klammert, U., Würzler, K., Müller, F. A., & Barralet, J. E. (2007). Resorbable Dicalcium Phosphate Bone Substitutes Prepared by 3D Powder Printing. Advanced Functional Materials. https://doi.org/10.1002/adfm.200700019
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.