The DOI matches its Crossref record.
Resorbable Dicalcium Phosphate Bone Substitutes Prepared by 3D Powder Printing
Abstract
Bioceramic bone substitutes with programmed architecture were manufactured at room temperature in this study using a novel 3D printing process that combined 3D powder printing with calcium phosphate cement chemistry. During printing, biphasic α/β‐tricalcium phosphate (Ca 3(PO 4)2, TCP) powder reacted with a liquid component consisting of phosphoric acid solution to form a matrix of dicalcium phosphate dihydrate (CaHPO 4·H 2 O, DCPD, brushite) and unreacted TCP. Printed samples showed compressive strengths between 0.9–8.7 MPa after printing depending on the acid concentration. A further strength improvement to a maximum of 22 MPa could be obtained by additional hardening of the samples in phosphoric acid for three one minute washes. After this treatment, the samples mainly consisted of brushite with minor phases of unreacted TCP and a lesser amount of dicalcium phosphate anhydrate (CaHPO 4, DCPA, monetite). Hydrothermal conversion of brushite to DCPA resulted in an increase of porosity of approximately 13 % and a decrease of strength to 15 MPa, however the resorption rate in vivo was increased as demonstrated after intramuscular implantation over 56 weeks. Major advantages compared with commonly used sintering techniques are the low processing temperature, which enables the fabrication of thermally instable and degradable matrices of secondary calcium phosphates.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Evaluation of 3D Printing and Its Potential Impact on Biotechnology and the Chemical Sciences
Gross, B. C., Erkal, J. L., Lockwood, S. Y., Chen, C., & Spence, D. M. (2014) · Analytical Chemistry · doi:10.1021/ac403397r · Cited by 1,746
3D bioactive composite scaffolds for bone tissue engineering
Turnbull, G., Clarke, J., Picard, F., Riches, P., Jia, L., Han, F., Li, B., & Shu, W. (2018) · Bioactive Materials · doi:10.1016/j.bioactmat.2017.10.001 · Cited by 1,332
Additive Manufacturing of Ceramic‐Based Materials
Travitzky, N., Bonet, A., Dermeik, B., Fey, T., Filbert‐Demut, I., Schlier, L., Schlordt, T., & Greil, P. (2014) · Advanced Engineering Materials · doi:10.1002/adem.201400097 · Cited by 878
Calcium phosphates in biomedical applications: materials for the future?
Habraken, W., Habibovic, P., Epple, M., & Bohner, M. (2016) · Materials Today · doi:10.1016/j.mattod.2015.10.008 · Cited by 857
3D printing of composite calcium phosphate and collagen scaffolds for bone regeneration
Inzana, J. A., Olvera, D., Fuller, S. M., Kelly, J. P., Graeve, O. A., Schwarz, E. M., Kates, S. L., & Awad, H. A. (2014) · Biomaterials · doi:10.1016/j.biomaterials.2014.01.064 · Cited by 840
Designing Biomaterials for 3D Printing
Guvendiren, M., Molde, J., Soares, R. M. D., & Kohn, J. (2016) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.6b00121 · Cited by 732
How smart do biomaterials need to be? A translational science and clinical point of view
Holzapfel, B. M., Reichert, J. C., Schantz, J.-T., Gbureck, U., Rackwitz, L., Nöth, U., Jakob, F., Rudert, M., Groll, J., & Hutmacher, D. W. (2013) · Advanced Drug Delivery Reviews · doi:10.1016/j.addr.2012.07.009 · Cited by 552
Self-citationBiodegradable Materials and Metallic Implants—A Review
Prakasam, M., Locs, J., Salma-Ancane, K., Loca, D., Largeteau, A., & Berzina-Cimdina, L. (2017) · Journal of Functional Biomaterials · doi:10.3390/jfb8040044 · Cited by 493
Properties of 3D-printed fiber-reinforced Portland cement paste
Hambach, M., & Volkmer, D. (2017) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2017.02.001 · Cited by 470
Butscher, A., Bohner, M., Hofmann, S., Gauckler, L., & Müller, R. (2011) · Acta Biomaterialia · doi:10.1016/j.actbio.2010.09.039 · Cited by 459
Dicalcium phosphate cements: Brushite and monetite
Tamimi, F., Sheikh, Z., & Barralet, J. (2012) · Acta Biomaterialia · doi:10.1016/j.actbio.2011.08.005 · Cited by 423
Self-citationSheikh, Z., Hamdan, N., Ikeda, Y., Grynpas, M., Ganss, B., & Glogauer, M. (2017) · Biomaterials Research · doi:10.1186/s40824-017-0095-5 · Cited by 393
3D Printing of Calcium Phosphate Ceramics for Bone Tissue Engineering and Drug Delivery
Trombetta, R., Inzana, J. A., Schwarz, E. M., Kates, S. L., & Awad, H. A. (2017) · Annals of Biomedical Engineering · doi:10.1007/s10439-016-1678-3 · Cited by 377
Osteoconduction and osteoinduction of low-temperature 3D printed bioceramic implants
Habibovic, P., Gbureck, U., Doillon, C. J., Bassett, D. C., van Blitterswijk, C. A., & Barralet, J. E. (2008) · Biomaterials · doi:10.1016/j.biomaterials.2007.10.023 · Cited by 347
Self-citationRecent advances in 3D printing of porous ceramics: A review
Hwa, L. C., Rajoo, S., Noor, A. M., Ahmad, N., & Uday, M. B. (2017) · Current Opinion in Solid State and Materials Science · doi:10.1016/j.cossms.2017.08.002 · Cited by 343
3D printing of bone substitute implants using calcium phosphate and bioactive glasses
Bergmann, C., Lindner, M., Zhang, W., Koczur, K., Kirsten, A., Telle, R., & Fischer, H. (2010) · Journal of the European Ceramic Society · doi:10.1016/j.jeurceramsoc.2010.04.037 · Cited by 311
Ginebra, M. P., Espanol, M., Montufar, E. B., Perez, R. A., & Mestres, G. (2010) · Acta Biomaterialia · doi:10.1016/j.actbio.2010.01.036 · Cited by 310
Advances in additive manufacturing for bone tissue engineering scaffolds
Moreno Madrid, A. P., Vrech, S. M., Sanchez, M. A., & Rodriguez, A. P. (2019) · Materials Science and Engineering: C · doi:10.1016/j.msec.2019.03.037 · Cited by 307
Preethi Soundarya, S., Haritha Menon, A., Viji Chandran, S., & Selvamurugan, N. (2018) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2018.08.056 · Cited by 305
Powder-based 3D printing for bone tissue engineering
Brunello, G., Sivolella, S., Meneghello, R., Ferroni, L., Gardin, C., Piattelli, A., Zavan, B., & Bressan, E. (2016) · Biotechnology Advances · doi:10.1016/j.biotechadv.2016.03.009 · Cited by 296
Calcium Orthophosphate-Based Bioceramics
Dorozhkin, S. (2013) · Materials · doi:10.3390/ma6093840 · Cited by 295
Farzadi, A., Solati-Hashjin, M., Asadi-Eydivand, M., & Abu Osman, N. A. (2014) · PLoS ONE · doi:10.1371/journal.pone.0108252 · Cited by 284
Calcium Orthophosphates as Bioceramics: State of the Art
Dorozhkin, S. V. (2010) · Journal of Functional Biomaterials · doi:10.3390/jfb1010022 · Cited by 278
3D printing of ceramic-based scaffolds for bone tissue engineering: an overview
Du, X., Fu, S., & Zhu, Y. (2018) · Journal of Materials Chemistry B · doi:10.1039/c8tb00677f · Cited by 259
Lin, K.-F., He, S., Song, Y., Wang, C.-M., Gao, Y., Li, J.-Q., Tang, P., Wang, Z., Bi, L., & Pei, G.-X. (2016) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.6b00815 · Cited by 176
Fine, N., Sheikh, Z., Al‐Jaf, F., Oveisi, M., Borenstein, A., Hu, Y., Pilliar, R., Grynpas, M., & Glogauer, M. (2020) · Journal of Biomedical Materials Research Part B: Applied Biomaterials · doi:10.1002/jbm.b.34385 · Cited by 9
Metadata
- Authors
- Gbureck, U., Hölzel, T., Klammert, U., Würzler, K., Müller, F. A., & Barralet, J. E.
- Venue
- Advanced Functional Materials
- Publisher
- Wiley
- Published
- 2007-11-28
- Volume
- 17
- Issue
- 18
- Pages
- 3940-3945
- ISSN
- 1616-301X (ISSN-L)
- 1616-3028
- OpenAlex
- W2117315764
- Cited by
- 233
- References
- 0
- FWCI
- 5.49
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.