The DOI matches its Crossref record; 280 of the 280 references it cites were found in a registry or an index.
A Review of 3D Printing Technologies for Soft Polymer Materials
Abstract
Soft polymer materials, which are similar to human tissues, have played critical roles in modern interdisciplinary research. Compared with conventional methods, 3D printing allows rapid prototyping and mass customization and is ideal for processing soft polymer materials. However, 3D printing of soft polymer materials is still in the early stages of development and is facing many challenges including limited printable materials, low printing resolution and speed, and poor functionalities. The present review aims to summarize the ideas to address these challenges. It focuses on three points: 1) how to develop printable materials and make unprintable materials printable, 2) how to choose suitable methods and improve printing resolution, and 3) how to directly construct functional structures/systems with 3D printing. After a brief introduction on this topic, the mainstream 3D printing technologies for printing soft polymer materials are reviewed, with an emphasis on improving printing resolution and speed, choosing suitable printing techniques, developing printable materials, and printing multiple materials. Moreover, the state‐of‐the‐art advancements in multimaterial 3D printing of soft polymer materials are summarized. Furthermore, the revolutions brought about by 3D printing of soft polymer materials for applications similar to biology are highlighted. Finally, viewpoints and future perspectives for this emerging field are discussed.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Items 201–280 of 280
3D printing a mechanically-tunable acrylate resin on a commercial DLP-SLA printer
Borrello, J., Nasser, P., Iatridis, J. C., & Costa, K. D. (2018) · Additive Manufacturing · doi:10.1016/j.addma.2018.08.019 · Cited by 193
Three-Dimensional Printing Fiber Reinforced Hydrogel Composites
Bakarich, S. E., Gorkin, R., in het Panhuis, M., & Spinks, G. M. (2014) · ACS Applied Materials & Interfaces · doi:10.1021/am503878d · Cited by 192
Rapid 3D Patterning of Poly(acrylic acid) Ionic Hydrogel for Miniature pH Sensors
Yin, M., Yao, M., Gao, S., Zhang, A. P., Tam, H., & Wai, P. A. (2016) · Advanced Materials · doi:10.1002/adma.201504021 · Cited by 190
4D Printing of Complex Structures with a Fast Response Time to Magnetic Stimulus
Zhu, P., Yang, W., Wang, R., Gao, S., Li, B., & Li, Q. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.8b12853 · Cited by 190
3D Printing by Multiphase Silicone/Water Capillary Inks
Roh, S., Parekh, D. P., Bharti, B., Stoyanov, S. D., & Velev, O. D. (2017) · Advanced Materials · doi:10.1002/adma.201701554 · Cited by 187
Bioprinting functional tissues
Leberfinger, A. N., Dinda, S., Wu, Y., Koduru, S. V., Ozbolat, V., Ravnic, D. J., & Ozbolat, I. T. (2019) · Acta Biomaterialia · doi:10.1016/j.actbio.2019.01.009 · Cited by 180
Influence of building strategies on the accuracy of parts in selective laser sintering
Senthilkumaran, K., Pandey, P. M., & Rao, P. V. M. (2009) · Materials & Design · doi:10.1016/j.matdes.2009.01.009 · Cited by 179
High-strength epoxy nanocomposites for 3D printing
Hmeidat, N. S., Kemp, J. W., & Compton, B. G. (2018) · Composites Science and Technology · doi:10.1016/j.compscitech.2018.03.008 · Cited by 177
Predicting phase behavior of grain boundaries with evolutionary search and machine learning
Zhu, Q., Samanta, A., Li, B., Rudd, R. E., & Frolov, T. (2018) · Nature Communications · doi:10.1038/s41467-018-02937-2 · Cited by 175
Micro/nanoscale electrohydrodynamic printing: from 2D to 3D
Zhang, B., He, J., Li, X., Xu, F., & Li, D. (2016) · Nanoscale · doi:10.1039/c6nr04106j · Cited by 172
Additive manufacturing of hydrogel-based materials for next-generation implantable medical devices
Chin, S. Y., Poh, Y. C., Kohler, A.-C., Compton, J. T., Hsu, L. L., Lau, K. M., Kim, S., Lee, B. W., Lee, F. Y., & Sia, S. K. (2017) · Science Robotics · doi:10.1126/scirobotics.aah6451 · Cited by 172
Multi-material, multi-technology FDM: exploring build process variations
Espalin, D., Alberto Ramirez, J., Medina, F., & Wicker, R. (2014) · Rapid Prototyping Journal · doi:10.1108/rpj-12-2012-0112 · Cited by 171
Designing toughness and strength for soft materials
Zhao, X. (2017) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1710942114 · Cited by 171
Three-dimensional inkjet biofabrication based on designed images
Arai, K., Iwanaga, S., Toda, H., Genci, C., Nishiyama, Y., & Nakamura, M. (2011) · Biofabrication · doi:10.1088/1758-5082/3/3/034113 · Cited by 167
Yang, Y., Chen, Z., Song, X., Zhu, B., Hsiai, T., Wu, P.-I., Xiong, R., Shi, J., Chen, Y., Zhou, Q., et al. (2016) · Nano Energy · doi:10.1016/j.nanoen.2016.02.045 · Cited by 166
Kowsari, K., Akbari, S., Wang, D., Fang, N. X., & Ge, Q. (2018) · 3D Printing and Additive Manufacturing · doi:10.1089/3dp.2018.0004 · Cited by 162
Fiber‐Based Mini Tissue with Morphology‐Controllable GelMA Microfibers
Shao, L., Gao, Q., Zhao, H., Xie, C., Fu, J., Liu, Z., Xiang, M., & He, Y. (2018) · Small · doi:10.1002/smll.201802187 · Cited by 161
Self-citationHigh‐Resolution Projection Microstereolithography for Patterning of Neovasculature
Raman, R., Bhaduri, B., Mir, M., Shkumatov, A., Lee, M. K., Popescu, G., Kong, H., & Bashir, R. (2016) · Advanced Healthcare Materials · doi:10.1002/adhm.201500721 · Cited by 159
de Ruijter, M., Ribeiro, A., Dokter, I., Castilho, M. D., & Malda, J. (2018) · Advanced Healthcare Materials · doi:10.1002/adhm.201800418 · Cited by 159
Lee, H. J., Kim, Y. B., Ahn, S. H., Lee, J., Jang, C. H., Yoon, H., Chun, W., & Kim, G. H. (2015) · Advanced Healthcare Materials · doi:10.1002/adhm.201500193 · Cited by 158
Porous polymeric materials by 3D printing of photocurable resin
Mu, X., Bertron, T., Dunn, C., Qiao, H., Wu, J., Zhao, Z., Saldaña, C., & Qi, H. J. (2017) · Materials Horizons · doi:10.1039/c7mh00084g · Cited by 158
3D Inkjet Printing of Complex, Cell-Laden Hydrogel Structures
Negro, A., Cherbuin, T., & Lütolf, M. P. (2018) · Scientific Reports · doi:10.1038/s41598-018-35504-2 · Cited by 158
Hydrophilic/Hydrophobic Composite Shape-Shifting Structures
Zhao, Z., Kuang, X., Yuan, C., Qi, H. J., & Fang, D. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.8b02444 · Cited by 152
Zhou, L., Gao, Q., Zhan, J.-F., Xie, C., Fu, J., & He, Y. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.8b06903 · Cited by 151
Self-citationSuperstretchable and Processable Silicone Elastomers by Digital Light Processing 3D Printing
Zhao, T., Yu, R., Li, S., Li, X., Zhang, Y., Yang, X. M., Zhao, X., Wang, C., Liu, Z., Dou, R., et al. (2019) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.9b03156 · Cited by 151
Wan, X., Zhang, F., Liu, Y., & Leng, J. (2019) · Carbon · doi:10.1016/j.carbon.2019.08.047 · Cited by 147
A general strategy of 3D printing thermosets for diverse applications
Lei, D., Yang, Y., Liu, Z., Chen, S., Song, B., Shen, A., Yang, B., Li, S., Yuan, Z., Qi, Q., et al. (2018) · Materials Horizons · doi:10.1039/c8mh00937f · Cited by 144
Metering and dispensing of powder; the quest for new solid freeforming techniques
Yang, S., & Evans, J. (2007) · Powder Technology · doi:10.1016/j.powtec.2007.04.004 · Cited by 140
Djumas, L., Molotnikov, A., Simon, G. P., & Estrin, Y. (2016) · Scientific Reports · doi:10.1038/srep26706 · Cited by 138
Inkjet 3D printing of UV and thermal cure silicone elastomers for dielectric elastomer actuators
McCoul, D., Rosset, S., Schlatter, S., & Shea, H. R. (2017) · Smart Materials and Structures · doi:10.1088/1361-665x/aa9695 · Cited by 138
3D printed electrically-driven soft actuators
Haghiashtiani, G., Habtour, E., Park, S. H., Gardea, F., & McAlpine, M. C. (2018) · Extreme Mechanics Letters · doi:10.1016/j.eml.2018.02.002 · Cited by 138
Printing Hydrogels and Elastomers in Arbitrary Sequence with Strong Adhesion
Yang, H., Li, C., Yang, M., Pan, Y., Yin, Q., Tang, J., Qi, H. J., & Suo, Z. (2019) · Advanced Functional Materials · doi:10.1002/adfm.201901721 · Cited by 136
Athreya, S. R., Kalaitzidou, K., & Das, S. (2010) · Composites Science and Technology · doi:10.1016/j.compscitech.2010.12.028 · Cited by 135
Zhang, B., Seong, B., Nguyen, V., & Byun, D. (2016) · Journal of Micromechanics and Microengineering · doi:10.1088/0960-1317/26/2/025015 · Cited by 134
Suspended Manufacture of Biological Structures
Moxon, S. R., Cooke, M. E., Cox, S. C., Snow, M., Jeys, L. M., Jones, S. W., Smith, A. M., & Grover, L. M. (2017) · Advanced Materials · doi:10.1002/adma.201605594 · Cited by 134
Li, C., Yang, H., Suo, Z., & Tang, J. (2019) · Journal of the Mechanics and Physics of Solids · doi:10.1016/j.jmps.2019.103751 · Cited by 132
Multimaterials 3D Printing for Free Assembly Manufacturing of Magnetic Driving Soft Actuator
Ji, Z., Yan, C., Yu, B., Wang, X., & Zhou, F. (2017) · Advanced Materials Interfaces · doi:10.1002/admi.201700629 · Cited by 131
3D-printing porosity: A new approach to creating elevated porosity materials and structures
Jakus, A. E., Geisendorfer, N. R., Lewis, P. L., & Shah, R. N. (2018) · Acta Biomaterialia · doi:10.1016/j.actbio.2018.03.039 · Cited by 131
Zheng, H., Zhang, J., Lu, S., Gaochao, W., & Xu, Z. (2005) · Materials Letters · doi:10.1016/j.matlet.2005.11.003 · Cited by 129
Dimas, L. S., & Buehler, M. J. (2014) · Soft Matter · doi:10.1039/c3sm52890a · Cited by 124
3D printed cellular solid outperforms traditional stochastic foam in long-term mechanical response
Maiti, A., Small, W., Lewicki, J. P., Weisgraber, T. H., Duoss, E. B., Chinn, S. C., Pearson, M. A., Spadaccini, C., Maxwell, R. S., & Wilson, T. S. (2016) · Scientific Reports · doi:10.1038/srep24871 · Cited by 109
Sacrificial microgel-laden bioink-enabled 3D bioprinting of mesoscale pore networks
Shao, L., Gao, Q., Xie, C., Fu, J., Xiang, M., Liu, Z., Xiang, L., & He, Y. (2020) · Bio-Design and Manufacturing · doi:10.1007/s42242-020-00062-y · Cited by 109
Self-citationOpen-Source Selective Laser Sintering (OpenSLS) of Nylon and Biocompatible Polycaprolactone
Kinstlinger, I. S., Andreas, B., Paulsen, S. J., Hwang, D. H., Ta, A. H., Yalacki, D. R., Schmidt, T., & Miller, J. S. (2016) · PLoS ONE · doi:10.1371/journal.pone.0147399 · Cited by 108
3D‐Printed Silicone Soft Architectures with Programmed Magneto‐Capillary Reconfiguration
Roh, S., Okello, L. B., Golbasi, N. C., Hankwitz, J. P., Liu, J. A. ‐., Tracy, J. B., & Velev, O. D. (2019) · Advanced Materials Technologies · doi:10.1002/admt.201800528 · Cited by 107
3D Printing of Highly Conductive Nanocomposites for the Functional Optimization of Liquid Sensors
Chizari, K., Daoud, M. A., Ravindran, A. R., & Therriault, D. (2016) · Small · doi:10.1002/smll.201601695 · Cited by 104
Three-Dimensional Bioprinting of Oppositely Charged Hydrogels with Super Strong Interface Bonding
Li, H., Tan, Y. J., Liu, S., & Li, L. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b19730 · Cited by 102
A self-healing, adaptive and conductive polymer composite ink for 3D printing of gas sensors
Wu, T., Gray, E., & Chen, B. (2018) · Journal of Materials Chemistry C · doi:10.1039/c8tc01092g · Cited by 102
3D printing of photocurable poly(glycerol sebacate) elastomers
Yeh, Y., Highley, C. B., Ouyang, L., & Burdick, J. A. (2016) · Biofabrication · doi:10.1088/1758-5090/8/4/045004 · Cited by 101
Sirrine, J. M., Meenakshisundaram, V., Moon, N. G., Scott, P. J., Mondschein, R. J., Weiseman, T. F., Williams, C. B., & Long, T. E. (2018) · Polymer · doi:10.1016/j.polymer.2018.02.056 · Cited by 96
3D bioprinting scaffold using alginate/polyvinyl alcohol bioinks
Luo, Y., Luo, G., Gelinsky, M., Huang, P., & Ruan, C. (2016) · Materials Letters · doi:10.1016/j.matlet.2016.12.009 · Cited by 95
Printing 3D microfluidic chips with a 3D sugar printer
He, Y., Qiu, J., Fu, J., Zhang, J., Ren, Y., & Liu, A. (2015) · Microfluidics and Nanofluidics · doi:10.1007/s10404-015-1571-7 · Cited by 94
Self-citationCai, Y., & Jessop, J. L. P. (2006) · Polymer · doi:10.1016/j.polymer.2006.07.031 · Cited by 92
A Nanosilica/Nylon-12 Composite Powder for Selective Laser Sintering
Chunze, Y., Yusheng, S., Jinsong, Y., et al. (2008) · Journal of Reinforced Plastics and Composites · doi:10.1177/0731684408094062 · Cited by 91
Electrically Conducting and Mechanically Strong Graphene–Polylactic Acid Composites for 3D Printing
Kim, M., Jeong, J. H., Lee, J., Capasso, A., Bonaccorso, F., Kang, S.-H., Lee, Y., & Lee, G. (2019) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.9b03241 · Cited by 91
Inkjet–Spray Hybrid Printing for 3D Freeform Fabrication of Multilayered Hydrogel Structures
Yoon, S., Park, J. A., Lee, H., Yoon, W., Hwang, D. S., & Jung, S. (2018) · Advanced Healthcare Materials · doi:10.1002/adhm.201800050 · Cited by 90
Photoreconfigurable Polymers for Biomedical Applications: Chemistry and Macromolecular Engineering
Zhu, C., Ninh, C., & Bettinger, C. J. (2014) · Biomacromolecules · doi:10.1021/bm500990z · Cited by 86
Gurr, M., Hofmann, D., Ehm, M., et al. (2008) · Advanced Functional Materials · doi:10.1002/adfm.200800344 · Cited by 84
Góra, A., Sahay, R., Thavasi, V., & Ramakrishna, S. (2011) · Journal of macromolecular science. Part C, Reviews in macromolecular chemistry and physics/Journal of macromolecular science. Reviews in macromolecular chemistry and physics · doi:10.1080/15583724.2011.594196 · Cited by 83
Duan, B., & Wang, M. (2010) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2010.05.022 · Cited by 83
Synchronous 3D Bioprinting of Large‐Scale Cell‐Laden Constructs with Nutrient Networks
Shao, L., Gao, Q., Xie, C., Fu, J., Xiang, M., & He, Y. (2019) · Advanced Healthcare Materials · doi:10.1002/adhm.201901142 · Cited by 83
Self-citationMultidimensional Vascularized Polymers using Degradable Sacrificial Templates
Gergely, R. C. R., Pety, S. J., Krull, B. P., Patrick, J. F., Doan, T. Q., Coppola, A. M., Thakre, P., Sottos, N. R., Moore, J. S., & White, S. R. (2014) · Advanced Functional Materials · doi:10.1002/adfm.201403670 · Cited by 74
Bioinspired Functional Surfaces Enabled by Multiscale Stereolithography
Li, Y., Mao, H., Hu, P., Hermes, M., Lim, H., Yoon, J., Luhar, M., Chen, Y., & Wu, W. (2019) · Advanced Materials Technologies · doi:10.1002/admt.201800638 · Cited by 74
Bioprinting of Cell‐Laden Microfiber: Can It Become a Standard Product?
Shao, L., Gao, Q., Xie, C., Fu, J., Xiang, M., & He, Y. (2019) · Advanced Healthcare Materials · doi:10.1002/adhm.201900014 · Cited by 74
Self-citationZhou, L., Ye, J.-H., Fu, J., Gao, Q., & He, Y. (2020) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.9b22433 · Cited by 74
Self-citation3D Printing of Free‐Standing Stretchable Electrodes with Tunable Structure and Stretchability
Wei, H., Li, K., Liu, W., Meng, H., Zhang, P. X., & Yan, C. Y. (2017) · Advanced Engineering Materials · doi:10.1002/adem.201700341 · Cited by 73
Why choose 3D bioprinting? Part II: methods and bioprinters
He, Y., Gu, Z., Xie, M., Fu, J., & Lin, H. M. (2020) · Bio-Design and Manufacturing · doi:10.1007/s42242-020-00064-w · Cited by 73
Self-citation4D printed porous radiopaque shape memory polyurethane for endovascular embolization
Kashyap, D., Kumar, P. K., & Kanagaraj, S. (2018) · Additive manufacturing · doi:10.1016/j.addma.2018.04.009 · Cited by 70
Li, H., Tan, Y. J., & Li, L. (2018) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2018.06.081 · Cited by 70
Liu, S., Hu, Y., Zhang, J., Bao, S., Xian, L., Dong, X., Zheng, W., Li, Y., Gao, H., & Zhou, W. (2019) · Macromolecular Materials and Engineering · doi:10.1002/mame.201800698 · Cited by 70
A new photocrosslinkable polycaprolactone‐based ink for three‐dimensional inkjet printing
He, Y., Tuck, C. J., Prina, E., Kilsby, S., Christie, S. D. R., Edmondson, S., Hague, R., Rose, F. R. A. J., & Wildman, R. D. (2016) · Journal of Biomedical Materials Research Part B Applied Biomaterials · doi:10.1002/jbm.b.33699 · Cited by 69
Self-citationBégin‐Drolet, A., Dussault, M.-A., Fernandez, S. A., Larose-Dutil, J., Leask, R. L., Hoesli, C. A., & Ruel, J. (2017) · Additive manufacturing · doi:10.1016/j.addma.2017.03.006 · Cited by 69
3D Printing of Photocuring Elastomers with Excellent Mechanical Strength and Resilience
Ji, Z., Zhang, X., Yan, C., Jia, X., Xia, Y., Wang, X., & Zhou, F. (2019) · Macromolecular Rapid Communications · doi:10.1002/marc.201800873 · Cited by 65
Towards Behavior Design of a 3D-Printed Soft Robotic Hand
Scharff, R. B. N., Doubrovski, E. L., Poelman, W., Jonker, P. P., Wang, C. C. L., & Geraedts, J. M. P. (2016) · Biosystems & biorobotics · doi:10.1007/978-3-319-46460-2_4 · Cited by 62
Azmi, S., Razak, S. I. A., Kadir, M. R. A., Iqbal, N., Hassan, R., Nayan, N. H. M., Wahab, A. H. A., & Shaharuddin, S. (2016) · Soft Materials · doi:10.1080/1539445x.2016.1242500 · Cited by 60
Farahani, R. D., Lebel, L. L., & Therriault, D. (2014) · Journal of Micromechanics and Microengineering · doi:10.1088/0960-1317/24/5/055020 · Cited by 57
Luan, C., Yao, X., Liu, C., Lan, L., & Fu, J. (2018) · Carbon · doi:10.1016/j.carbon.2018.08.019 · Cited by 57
Self-citationMulti-material Additive Manufacturing of Functional Soft Robot
Joyee, E. B., & Pan, Y. (2019) · Procedia Manufacturing · doi:10.1016/j.promfg.2019.06.221 · Cited by 50
Omnidirectional Printing of Soft Elastomer for Liquid-State Stretchable Electronics
Wang, J., Yang, S., Ding, P., Cao, X., Zhang, Y., Cao, S., Zhang, K., Kong, S., Zhou, Y., Wang, X., et al. (2019) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.9b04730 · Cited by 45
UV laser direct writing of 2D/3D structures using photo-curable polydimethylsiloxane (PDMS)
Obata, K., Slobin, S., Schonewille, A., et al. (2017) · Applied Physics A · doi:10.1007/s00339-017-1104-1 · Cited by 27
Additive Manufacturing with Ultraviolet Curable Silicones Containing Carbon Black
Porter, D. A., Cohen, A. L., Krueger, P. S., & Son, D. Y. (2018) · 3D Printing and Additive Manufacturing · doi:10.1089/3dp.2017.0019 · Cited by 26
Cited by
Bioinspired marine antifouling coatings: Status, prospects, and future
Jin, H., Tian, L., Bing, W., Zhao, J., & Ren, L. (2022) · Progress in Materials Science · doi:10.1016/j.pmatsci.2021.100889 · Cited by 585
Wang, H., Zhang, W., Ladika, D., Yu, H., Gailevičius, D., Wang, H., Pan, C., Nair, P. N. S., Ke, Y., Mori, T., et al. (2023) · Advanced Functional Materials · doi:10.1002/adfm.202214211 · Cited by 401
3D-printed self-healing hydrogels via Digital Light Processing
Caprioli, M., Roppolo, I., Chiappone, A., Larush, L., Pirri, C. F., & Magdassi, S. (2021) · Nature Communications · doi:10.1038/s41467-021-22802-z · Cited by 335
Tardy, B. L., Mattos, B. D., Otoni, C. G., Beaumont, M., Majoinen, J., Kämäräinen, T., & Rojas, O. J. (2021) · Chemical Reviews · doi:10.1021/acs.chemrev.0c01333 · Cited by 267
Emerging Technologies in Multi‐Material Bioprinting
Ravanbakhsh, H., Karamzadeh, V., Bao, G., Mongeau, L., Juncker, D., & Zhang, Y. S. (2021) · Advanced Materials · doi:10.1002/adma.202104730 · Cited by 266
Metadata
- Authors
- Zhou, L., Fu, J., & He, Y.
- Venue
- Advanced Functional Materials
- Publisher
- Wiley
- Published
- 2020-04-29
- Volume
- 30
- Issue
- 28
- ISSN
- 1616-301X (ISSN-L)
- 1616-3028
- OpenAlex
- W3023001773
- Cited by
- 713
- References
- 280
- FWCI
- 27.50
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.