The DOI matches its Crossref record; 280 of the 280 references it cites were found in a registry or an index.
A Review of 3D Printing Technologies for Soft Polymer Materials
Abstract
Soft polymer materials, which are similar to human tissues, have played critical roles in modern interdisciplinary research. Compared with conventional methods, 3D printing allows rapid prototyping and mass customization and is ideal for processing soft polymer materials. However, 3D printing of soft polymer materials is still in the early stages of development and is facing many challenges including limited printable materials, low printing resolution and speed, and poor functionalities. The present review aims to summarize the ideas to address these challenges. It focuses on three points: 1) how to develop printable materials and make unprintable materials printable, 2) how to choose suitable methods and improve printing resolution, and 3) how to directly construct functional structures/systems with 3D printing. After a brief introduction on this topic, the mainstream 3D printing technologies for printing soft polymer materials are reviewed, with an emphasis on improving printing resolution and speed, choosing suitable printing techniques, developing printable materials, and printing multiple materials. Moreover, the state‐of‐the‐art advancements in multimaterial 3D printing of soft polymer materials are summarized. Furthermore, the revolutions brought about by 3D printing of soft polymer materials for applications similar to biology are highlighted. Finally, viewpoints and future perspectives for this emerging field are discussed.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Langer, R., & Vacanti, J. P. (1993) · Science · doi:10.1126/science.8493529 · Cited by 9,893
Design, fabrication and control of soft robots
Rus, D., & Tolley, M. T. (2015) · Nature · doi:10.1038/nature14543 · Cited by 5,825
Highly stretchable and tough hydrogels
Sun, J.-Y., Zhao, X., Illeperuma, W. R. K., Chaudhuri, O., Oh, K. H., Mooney, D. J., Vlassak, J. J., & Suo, Z. (2012) · Nature · doi:10.1038/nature11409 · Cited by 5,481
Materials and Mechanics for Stretchable Electronics
Rogers, J. A., Someya, T., & Huang, Y. (2010) · Science · doi:10.1126/science.1182383 · Cited by 5,042
Bioinspired structural materials
Wegst, U. G. K., Bai, H., Saiz, E., Tomsia, A. P., & Ritchie, R. O. (2015) · Nature Materials · doi:10.1038/nmat4089 · Cited by 4,721
Xia, Y., & Whitesides, G. M. (1998) · Annual Review of Materials Science · doi:10.1146/annurev.matsci.28.1.153 · Cited by 4,611
Polymers for 3D Printing and Customized Additive Manufacturing
Ligon, S. C., Liska, R., Stampfl, J., Gurr, M., & Mülhaupt, R. (2017) · Chemical Reviews · doi:10.1021/acs.chemrev.7b00074 · Cited by 3,741
3D printing of polymer matrix composites: A review and prospective
Wang, X., Jiang, M., Zhou, Z., Gou, J., & Hui, D. (2017) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2016.11.034 · Cited by 3,325
High-Resolution Inkjet Printing of All-Polymer Transistor Circuits
Sirringhaus, H., Kawase, T., Friend, R. H., Shimoda, T., Inbasekaran, M., Wu, W., & Woo, E. P. (2000) · Science · doi:10.1126/science.290.5499.2123 · Cited by 3,311
Disintegration of water drops in an electric field
Taylor, G. I. (1964) · Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences · doi:10.1098/rspa.1964.0151 · Cited by 3,305
Synthesis, properties, and biomedical applications of gelatin methacryloyl (GelMA) hydrogels
Yue, K., Trujillo-de Santiago, G., Alvarez, M. M., Tamayol, A., Annabi, N., & Khademhosseini, A. (2015) · Biomaterials · doi:10.1016/j.biomaterials.2015.08.045 · Cited by 3,146
Sydney Gladman, A., Matsumoto, E. A., Nuzzo, R. G., Mahadevan, L., & Lewis, J. A. (2016) · Nature Materials · doi:10.1038/nmat4544 · Cited by 3,027
Review of selective laser melting: Materials and applications
Yap, C. Y., Chua, C. K., Dong, Z. L., Liu, Z. H., Zhang, D. Q., Loh, L. E., & Sing, S. L. (2015) · Applied Physics Reviews · doi:10.1063/1.4935926 · Cited by 2,353
Alginate hydrogels as synthetic extracellular matrix materials
Rowley, J. A., Madlambayan, G., & Mooney, D. J. (1999) · Biomaterials · doi:10.1016/s0142-9612(98)00107-0 · Cited by 2,342
Continuous liquid interface production of 3D objects
Tumbleston, J. R., Shirvanyants, D., Ermoshkin, N., Janusziewicz, R., Johnson, A. R., Kelly, D., Chen, K., Pinschmidt, R., Rolland, J. P., Ermoshkin, A., et al. (2015) · Science · doi:10.1126/science.aaa2397 · Cited by 2,278
Printing ferromagnetic domains for untethered fast-transforming soft materials
Kim, Y., Yuk, H., Zhao, R., Chester, S. A., & Zhao, X. (2018) · Nature · doi:10.1038/s41586-018-0185-0 · Cited by 2,183
An integrated design and fabrication strategy for entirely soft, autonomous robots
Wehner, M., Truby, R. L., Fitzgerald, D. J., Mosadegh, B., Whitesides, G. M., Lewis, J. A., & Wood, R. J. (2016) · Nature · doi:10.1038/nature19100 · Cited by 2,127
3D bioprinting of vascularized, heterogeneous cell-laden tissue constructs
Kolesky, D. B., Truby, R. L., Gladman, A. S., Busbee, T. A., Homan, K. A., & Lewis, J. A. (2014) · Advanced Materials · doi:10.1002/adma.201305506 · Cited by 2,102
Derby, B. (2010) · Annual Review of Materials Research · doi:10.1146/annurev-matsci-070909-104502 · Cited by 1,984
Shintake, J., Cacucciolo, V., Floreano, D., & Shea, H. (2018) · Advanced Materials · doi:10.1002/adma.201707035 · Cited by 1,938
Rapid casting of patterned vascular networks for perfusable engineered three-dimensional tissues
Miller, J. S., Stevens, K. R., Yang, M. T., Baker, B. M., Nguyen, D.-H. T., Cohen, D. M., Toro, E., Chen, A. A., Galie, P. A., Yu, X., et al. (2012) · Nature Materials · doi:10.1038/nmat3357 · Cited by 1,917
Additive manufacturing and its societal impact: a literature review
Huang, S. H., Liu, P., Mokasdar, A., & Hou, L. (2013) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-012-4558-5 · Cited by 1,862
Inkjet Printing for Materials and Devices
Calvert, P. (2001) · Chemistry of Materials · doi:10.1021/cm0101632 · Cited by 1,822
Hinton, T. J., Jallerat, Q., Palchesko, R. N., Park, J. H., Grodzicki, M. S., Shue, H.-J., Ramadan, M. H., Hudson, A. R., & Feinberg, A. W. (2015) · Science Advances · doi:10.1126/sciadv.1500758 · Cited by 1,805
3D bioprinting of collagen to rebuild components of the human heart
Lee, A., Hudson, A. R., Shiwarski, D. J., Tashman, J. W., Hinton, T. J., Yerneni, S., Bliley, J. M., Campbell, P. G., & Feinberg, A. W. (2019) · Science · doi:10.1126/science.aav9051 · Cited by 1,782
Direct Ink Writing of 3D Functional Materials
Lewis, J. A. (2006) · Advanced Functional Materials · doi:10.1002/adfm.200600434 · Cited by 1,740
3D printing with polymers: Challenges among expanding options and opportunities
Stansbury, J. W., & Idacavage, M. J. (2016) · Dental Materials · doi:10.1016/j.dental.2015.09.018 · Cited by 1,732
Lab-on-Skin: A Review of Flexible and Stretchable Electronics for Wearable Health Monitoring
Liu, Y., Pharr, M., & Salvatore, G. A. (2017) · ACS Nano · doi:10.1021/acsnano.7b04898 · Cited by 1,725
Ning, F., Cong, W., Qiu, J., Wei, J., & Wang, S. (2015) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2015.06.013 · Cited by 1,718
3D‐Printing of Lightweight Cellular Composites
Compton, B. G., & Lewis, J. A. (2014) · Advanced Materials · doi:10.1002/adma.201401804 · Cited by 1,626
Perspective on the Development of High‐Toughness Ceramics
Evans, A. G. (1990) · Journal of the American Ceramic Society · doi:10.1111/j.1151-2916.1990.tb06493.x · Cited by 1,625
Printing soft matter in three dimensions
Truby, R. L., & Lewis, J. A. (2016) · Nature · doi:10.1038/nature21003 · Cited by 1,622
Embedded 3D Printing of Strain Sensors within Highly Stretchable Elastomers
Muth, J. T., Vogt, D. M., Truby, R. L., Mengüç, Y., Kolesky, D. B., Wood, R. J., & Lewis, J. A. (2014) · Advanced Materials · doi:10.1002/adma.201400334 · Cited by 1,611
Universal robotic gripper based on the jamming of granular material
Brown, E., Rodenberg, N., Amend, J., Mozeika, A., Steltz, E., Zakin, M. R., Lipson, H., & Jaeger, H. M. (2010) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1003250107 · Cited by 1,603
3D printing based on imaging data: review of medical applications
Rengier, F., Mehndiratta, A., von Tengg-Kobligk, H., Zechmann, C. M., Unterhinninghofen, R., Kauczor, H.-U., & Giesel, F. L. (2010) · International Journal of Computer Assisted Radiology and Surgery · doi:10.1007/s11548-010-0476-x · Cited by 1,584
Soft robotics: Technologies and systems pushing the boundaries of robot abilities
Laschi, C., Mazzolai, B., & Cianchetti, M. (2016) · Science Robotics · doi:10.1126/scirobotics.aah3690 · Cited by 1,570
Bone tissue engineering using polycaprolactone scaffolds fabricated via selective laser sintering
Williams, J. M., Adewunmi, A., Schek, R. M., Flanagan, C. L., Krebsbach, P. H., Feinberg, S. E., Hollister, S. J., & Das, S. (2005) · Biomaterials · doi:10.1016/j.biomaterials.2004.11.057 · Cited by 1,563
Highly oriented carbon fiber–polymer composites via additive manufacturing
Tekinalp, H. L., Kunc, V., Velez-Garcia, G. M., Duty, C. E., Love, L. J., Naskar, A. K., Blue, C. A., & Ozcan, S. (2014) · Composites Science and Technology · doi:10.1016/j.compscitech.2014.10.009 · Cited by 1,514
Three-dimensional bioprinting of thick vascularized tissues
Kolesky, D. B., Homan, K. A., Skylar-Scott, M. A., & Lewis, J. A. (2016) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1521342113 · Cited by 1,492
A review of melt extrusion additive manufacturing processes: I. Process design and modeling
N. Turner, B., Strong, R., & A. Gold, S. (2014) · Rapid Prototyping Journal · doi:10.1108/rpj-01-2013-0012 · Cited by 1,450
Consolidation phenomena in laser and powder-bed based layered manufacturing
Kruth, J.-P., Levy, G., Klocke, F., & Childs, T. H. C. (2007) · CIRP Annals · doi:10.1016/j.cirp.2007.10.004 · Cited by 1,444
Biomedical applications of soft robotics
Cianchetti, M., Laschi, C., Menciassi, A., & Dario, P. (2018) · Nature Reviews Materials · doi:10.1038/s41578-018-0022-y · Cited by 1,435
Multivascular networks and functional intravascular topologies within biocompatible hydrogels
Grigoryan, B., Paulsen, S. J., Corbett, D. C., Sazer, D. W., Fortin, C. L., Zaita, A. J., Greenfield, P. T., Calafat, N. J., Gounley, J. P., Ta, A. H., et al. (2019) · Science · doi:10.1126/science.aav9750 · Cited by 1,396
Binding mechanisms in selective laser sintering and selective laser melting
Kruth, J., Mercelis, P., Van Vaerenbergh, J., Froyen, L., & Rombouts, M. (2005) · Rapid Prototyping Journal · doi:10.1108/13552540510573365 · Cited by 1,383
Wearable and flexible electronics for continuous molecular monitoring
Yang, Y., & Gao, W. (2019) · Chemical Society Reviews · doi:10.1039/c7cs00730b · Cited by 1,315
Ferromagnetic soft continuum robots
Kim, Y., Parada, G. A., Liu, S., & Zhao, X. (2019) · Science Robotics · doi:10.1126/scirobotics.aax7329 · Cited by 1,312
Multi-scale multi-mechanism design of tough hydrogels: building dissipation into stretchy networks
Zhao, X. (2014) · Soft Matter · doi:10.1039/c3sm52272e · Cited by 1,252
The hierarchical structure and mechanics of plant materials
Gibson, L. J. (2012) · Journal of The Royal Society Interface · doi:10.1098/rsif.2012.0341 · Cited by 1,215
Principles of polymer processing
(2007) · Choice Reviews Online · doi:10.5860/choice.44-2729 · Cited by 1,205
Three-dimensional printing of continuous-fiber composites by in-nozzle impregnation
Matsuzaki, R., Ueda, M., Namiki, M., Jeong, T.-K., Asahara, H., Horiguchi, K., Nakamura, T., Todoroki, A., & Hirano, Y. (2016) · Scientific Reports · doi:10.1038/srep23058 · Cited by 1,171
Levy, G. N., Schindel, R., & Kruth, J. P. (2003) · CIRP Annals · doi:10.1016/s0007-8506(07)60206-6 · Cited by 1,121
Gómez-Bombarelli, R., Aguilera-Iparraguirre, J., Hirzel, T. D., Duvenaud, D., Maclaurin, D., Blood-Forsythe, M. A., Chae, H. S., Einzinger, M., Ha, D.-G., Wu, T., et al. (2016) · Nature Materials · doi:10.1038/nmat4717 · Cited by 1,060
A 3D-printed, functionally graded soft robot powered by combustion
Bartlett, N. W., Tolley, M. T., Overvelde, J. T. B., Weaver, J. C., Mosadegh, B., Bertoldi, K., Whitesides, G. M., & Wood, R. J. (2015) · Science · doi:10.1126/science.aab0129 · Cited by 1,052
Direct 3D Printing of Shear‐Thinning Hydrogels into Self‐Healing Hydrogels
Highley, C. B., Rodell, C. B., & Burdick, J. A. (2015) · Advanced Materials · doi:10.1002/adma.201501234 · Cited by 1,043
3D Printing of Personalized Thick and Perfusable Cardiac Patches and Hearts
Noor, N., Shapira, A., Edri, R., Gal, I., Wertheim, L., & Dvir, T. (2019) · Advanced Science · doi:10.1002/advs.201900344 · Cited by 1,042
On the mechanics of mother-of-pearl: A key feature in the material hierarchical structure
BARTHELAT, F., TANG, H., ZAVATTIERI, P., LI, C., & ESPINOSA, H. (2007) · Journal of the Mechanics and Physics of Solids · doi:10.1016/j.jmps.2006.07.007 · Cited by 1,032
Volumetric additive manufacturing via tomographic reconstruction
Kelly, B. E., Bhattacharya, I., Heidari, H., Shusteff, M., Spadaccini, C. M., & Taylor, H. K. (2019) · Science · doi:10.1126/science.aau7114 · Cited by 1,025
Voxelated soft matter via multimaterial multinozzle 3D printing
Skylar-Scott, M. A., Mueller, J., Visser, C. W., & Lewis, J. A. (2019) · Nature · doi:10.1038/s41586-019-1736-8 · Cited by 1,024
Multiprocess 3D printing for increasing component functionality
MacDonald, E., & Wicker, R. (2016) · Science · doi:10.1126/science.aaf2093 · Cited by 961
Paxton, N., Smolan, W., Böck, T., Melchels, F., Groll, J., & Jungst, T. (2017) · Biofabrication · doi:10.1088/1758-5090/aa8dd8 · Cited by 950
Biomanufacturing of organ-specific tissues with high cellular density and embedded vascular channels
Skylar-Scott, M. A., Uzel, S. G. M., Nam, L. L., Ahrens, J. H., Truby, R. L., Damaraju, S., & Lewis, J. A. (2019) · Science Advances · doi:10.1126/sciadv.aaw2459 · Cited by 943
Tran, K., & Ulissi, Z. W. (2018) · Nature Catalysis · doi:10.1038/s41929-018-0142-1 · Cited by 920
A comparison of rapid prototyping technologies
Pham, D. T., & Gault, R. S. (1998) · International Journal of Machine Tools and Manufacture · doi:10.1016/s0890-6955(97)00137-5 · Cited by 915
Review on micro molding of thermoplastic polymers
Heckele, M., & Schomburg, W. K. (2004) · Journal of Micromechanics and Microengineering · doi:10.1088/0960-1317/14/3/r01 · Cited by 915
3D Printing of Shape Memory Polymers for Flexible Electronic Devices
Zarek, M., Layani, M., Cooperstein, I., Sachyani, E., Cohn, D., & Magdassi, S. (2016) · Advanced Materials · doi:10.1002/adma.201503132 · Cited by 903
Projection micro-stereolithography using digital micro-mirror dynamic mask
Sun, C., Fang, N., Wu, D. M., & Zhang, X. (2005) · Sensors and Actuators A: Physical · doi:10.1016/j.sna.2004.12.011 · Cited by 880
Mannoor, M. S., Jiang, Z., James, T., Kong, Y. L., Malatesta, K. A., Soboyejo, W. O., Verma, N., Gracias, D. H., & McAlpine, M. C. (2013) · Nano Letters · doi:10.1021/nl4007744 · Cited by 874
3D Printing of Highly Stretchable and Tough Hydrogels into Complex, Cellularized Structures
Hong, S., Sycks, D., Chan, H. F., Lin, S., Lopez, G. P., Guilak, F., Leong, K. W., & Zhao, X. (2015) · Advanced Materials · doi:10.1002/adma.201501099 · Cited by 873
Deterministically patterned biomimetic human iPSC-derived hepatic model via rapid 3D bioprinting
Ma, X., Qu, X., Zhu, W., Li, Y.-S., Yuan, S., Zhang, H., Liu, J., Wang, P., Lai, C. S. E., Zanella, F., et al. (2016) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1524510113 · Cited by 872
Loessner, D., Meinert, C., Kaemmerer, E., Martine, L. C., Yue, K., Levett, P. A., Klein, T. J., Melchels, F. P. W., Khademhosseini, A., & Hutmacher, D. W. (2016) · Nature Protocols · doi:10.1038/nprot.2016.037 · Cited by 868
Instrumented cardiac microphysiological devices via multimaterial three-dimensional printing
Lind, J. U., Busbee, T. A., Valentine, A. D., Pasqualini, F. S., Yuan, H., Yadid, M., Park, S.-J., Kotikian, A., Nesmith, A. P., Campbell, P. H., et al. (2017) · Nature Materials · doi:10.1038/nmat4782 · Cited by 863
Microfluidic Bioprinting of Heterogeneous 3D Tissue Constructs Using Low‐Viscosity Bioink
Colosi, C., Shin, S. R., Manoharan, V., Massa, S., Costantini, M., Barbetta, A., Dokmeci, M. R., Dentini, M., & Khademhosseini, A. (2016) · Advanced Materials · doi:10.1002/adma.201503310 · Cited by 863
Flexible Electronics: Stretchable Electrodes and Their Future
Huang, S., Liu, Y., Zhao, Y., Ren, Z., & Guo, C. F. (2019) · Advanced Functional Materials · doi:10.1002/adfm.201805924 · Cited by 855
Multimaterial magnetically assisted 3D printing of composite materials
Kokkinis, D., Schaffner, M., & Studart, A. R. (2015) · Nature Communications · doi:10.1038/ncomms9643 · Cited by 848
Omnidirectional Printing of 3D Microvascular Networks
Wu, W., DeConinck, A., & Lewis, J. A. (2011) · Advanced Materials · doi:10.1002/adma.201004625 · Cited by 819
Dickson, A. N., Barry, J. N., McDonnell, K. A., & Dowling, D. P. (2017) · Additive Manufacturing · doi:10.1016/j.addma.2017.06.004 · Cited by 792
Turner, B. N., & Gold, S. A. (2015) · Rapid Prototyping Journal · doi:10.1108/rpj-02-2013-0017 · Cited by 770
Shirazi, S. F. S., Gharehkhani, S., Mehrali, M., Yarmand, H., Metselaar, H. S. C., Adib Kadri, N., & Osman, N. A. A. (2015) · Science and Technology of Advanced Materials · doi:10.1088/1468-6996/16/3/033502 · Cited by 755
Reinforcement of hydrogels using three-dimensionally printed microfibres
Visser, J., Melchels, F. P. W., Jeon, J. E., van Bussel, E. M., Kimpton, L. S., Byrne, H. M., Dhert, W. J. A., Dalton, P. D., Hutmacher, D. W., & Malda, J. (2015) · Nature Communications · doi:10.1038/ncomms7933 · Cited by 718
Rapid prototyping of continuous carbon fiber reinforced polylactic acid composites by 3D printing
Li, N., Li, Y., & Liu, S. (2016) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2016.07.025 · Cited by 707
Nanomaterial‐Enabled Stretchable Conductors: Strategies, Materials and Devices
Yao, S., & Zhu, Y. (2015) · Advanced Materials · doi:10.1002/adma.201404446 · Cited by 695
Hybrid 3D Printing of Soft Electronics
Valentine, A. D., Busbee, T. A., Boley, J. W., Raney, J. R., Chortos, A., Kotikian, A., Berrigan, J. D., Durstock, M. F., & Lewis, J. A. (2017) · Advanced Materials · doi:10.1002/adma.201703817 · Cited by 688
Composites Reinforced in Three Dimensions by Using Low Magnetic Fields
Erb, R. M., Libanori, R., Rothfuchs, N., & Studart, A. R. (2012) · Science · doi:10.1126/science.1210822 · Cited by 675
Lamellar Bone: Structure–Function Relations
Weiner, S., Traub, W., & Wagner, H. D. (1999) · Journal of Structural Biology · doi:10.1006/jsbi.1999.4107 · Cited by 674
Highly Stretchable and UV Curable Elastomers for Digital Light Processing Based 3D Printing
Patel, D. K., Sakhaei, A. H., Layani, M., Zhang, B., Ge, Q., & Magdassi, S. (2017) · Advanced Materials · doi:10.1002/adma.201606000 · Cited by 673
Darabi, M. A., Khosrozadeh, A., Mbeleck, R., Liu, Y., Chang, Q., Jiang, J., Cai, J., Wang, Q., Luo, G., & Xing, M. (2017) · Advanced Materials · doi:10.1002/adma.201700533 · Cited by 672
Automatic method for fabricating a three-dimensional plastic model with photo-hardening polymer
Kodama, H. (1981) · Review of Scientific Instruments · doi:10.1063/1.1136492 · Cited by 668
Oppositely Charged Polyelectrolytes Form Tough, Self‐Healing, and Rebuildable Hydrogels
Luo, F., Sun, T. L., Nakajima, T., Kurokawa, T., Zhao, Y., Sato, K., Ihsan, A. B., Li, X., Guo, H., & Gong, J. P. (2015) · Advanced Materials · doi:10.1002/adma.201500140 · Cited by 664
Applications of Alginate-Based Bioinks in 3D Bioprinting
Axpe, E., & Oyen, M. (2016) · International Journal of Molecular Sciences · doi:10.3390/ijms17121976 · Cited by 663
Materials and Structures toward Soft Electronics
Wang, C., Wang, C., Huang, Z., & Xu, S. (2018) · Advanced Materials · doi:10.1002/adma.201801368 · Cited by 662
Anti-fatigue-fracture hydrogels
Lin, S., Liu, X., Liu, J., Yuk, H., Loh, H.-C., Parada, G. A., Settens, C., Song, J., Masic, A., McKinley, G. H., et al. (2019) · Science Advances · doi:10.1126/sciadv.aau8528 · Cited by 662
Heo, J. S., Eom, J., Kim, Y., & Park, S. K. (2018) · Small · doi:10.1002/smll.201703034 · Cited by 631
Coaxial nozzle-assisted 3D bioprinting with built-in microchannels for nutrients delivery
Gao, Q., He, Y., Fu, J.-Z., Liu, A., & Ma, L. (2015) · Biomaterials · doi:10.1016/j.biomaterials.2015.05.031 · Cited by 630
Self-citationMechanical characterization of parts fabricated using fused deposition modeling
Bellini, A., & Güçeri, S. (2003) · Rapid Prototyping Journal · doi:10.1108/13552540310489631 · Cited by 628
Xing, J.-F., Zheng, M.-L., & Duan, X.-M. (2015) · Chemical Society Reviews · doi:10.1039/c5cs00278h · Cited by 628
Spierings, A. B., Herres, N., & Levy, G. (2011) · Rapid Prototyping Journal · doi:10.1108/13552541111124770 · Cited by 614
A Tissue-Like Printed Material
Villar, G., Graham, A. D., & Bayley, H. (2013) · Science · doi:10.1126/science.1229495 · Cited by 613
Wu, Z. L., Moshe, M., Greener, J., Therien-Aubin, H., Nie, Z., Sharon, E., & Kumacheva, E. (2013) · Nature Communications · doi:10.1038/ncomms2549 · Cited by 607
Farahani, R. D., Dubé, M., & Therriault, D. (2016) · Advanced Materials · doi:10.1002/adma.201506215 · Cited by 604
Volumetric Bioprinting of Complex Living‐Tissue Constructs within Seconds
Bernal, P. N., Delrot, P., Loterie, D., Li, Y., Malda, J., Moser, C., & Levato, R. (2019) · Advanced Materials · doi:10.1002/adma.201904209 · Cited by 604
Mechanisms, Capabilities, and Applications of High‐Resolution Electrohydrodynamic Jet Printing
Onses, M. S., Sutanto, E., Ferreira, P. M., Alleyne, A. G., & Rogers, J. A. (2015) · Small · doi:10.1002/smll.201500593 · Cited by 603
Numerical Calculation of the Fluid Dynamics of Drop-on-Demand Jets
Fromm, J. E. (1984) · IBM Journal of Research and Development · doi:10.1147/rd.283.0322 · Cited by 601
High-Force Soft Printable Pneumatics for Soft Robotic Applications
Yap, H. K., Ng, H. Y., & Yeow, C.-H. (2016) · Soft Robotics · doi:10.1089/soro.2016.0030 · Cited by 601
Dependence of mechanical properties of polyamide components on build parameters in the SLS process
Caulfield, B., McHugh, P. E., & Lohfeld, S. (2007) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2006.09.007 · Cited by 598
Yin, J., Yan, M., Wang, Y., Fu, J., & Suo, H. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b16059 · Cited by 598
Self-citationMelenka, G. W., Cheung, B. K. O., Schofield, J. S., Dawson, M. R., & Carey, J. P. (2016) · Composite Structures · doi:10.1016/j.compstruct.2016.07.018 · Cited by 597
Soft Somatosensitive Actuators via Embedded 3D Printing
Truby, R. L., Wehner, M., Grosskopf, A. K., Vogt, D. M., Uzel, S. G. M., Wood, R. J., & Lewis, J. A. (2018) · Advanced Materials · doi:10.1002/adma.201706383 · Cited by 586
Grayscale digital light processing 3D printing for highly functionally graded materials
Kuang, X., Wu, J., Chen, K., Zhao, Z., Ding, Z., Hu, F., Fang, D., & Qi, H. J. (2019) · Science Advances · doi:10.1126/sciadv.aav5790 · Cited by 568
Programming magnetic anisotropy in polymeric microactuators
Kim, J., Chung, S. E., Choi, S.-E., Lee, H., Kim, J., & Kwon, S. (2011) · Nature Materials · doi:10.1038/nmat3090 · Cited by 556
Direct Writing of Gallium‐Indium Alloy for Stretchable Electronics
Boley, J. W., White, E. L., Chiu, G. T. ‐., & Kramer, R. K. (2014) · Advanced Functional Materials · doi:10.1002/adfm.201303220 · Cited by 546
Yang, Y., Song, X., Li, X., Chen, Z., Zhou, C., Zhou, Q., & Chen, Y. (2018) · Advanced Materials · doi:10.1002/adma.201706539 · Cited by 538
Soft network composite materials with deterministic and bio-inspired designs
Jang, K.-I., Chung, H. U., Xu, S., Lee, C. H., Luan, H., Jeong, J., Cheng, H., Kim, G.-T., Han, S. Y., Lee, J. W., et al. (2015) · Nature Communications · doi:10.1038/ncomms7566 · Cited by 533
Yang, Y., Li, X., Zheng, X., Chen, Z., Zhou, Q., & Chen, Y. (2018) · Advanced Materials · doi:10.1002/adma.201704912 · Cited by 525
3D printing of robotic soft actuators with programmable bioinspired architectures
Schaffner, M., Faber, J. A., Pianegonda, L., Rühs, P. A., Coulter, F., & Studart, A. R. (2018) · Nature Communications · doi:10.1038/s41467-018-03216-w · Cited by 518
Designing bioinspired composite reinforcement architectures via 3D magnetic printing
Martin, J. J., Fiore, B. E., & Erb, R. M. (2015) · Nature Communications · doi:10.1038/ncomms9641 · Cited by 515
Fast‐Response, Stiffness‐Tunable Soft Actuator by Hybrid Multimaterial 3D Printing
Zhang, Y., Zhang, N., Hingorani, H., Ding, N., Wang, D., Yuan, C., Zhang, B., Gu, G., & Ge, Q. (2019) · Advanced Functional Materials · doi:10.1002/adfm.201806698 · Cited by 513
Scalable submicrometer additive manufacturing
Saha, S. K., Wang, D., Nguyen, V. H., Chang, Y., Oakdale, J. S., & Chen, S.-C. (2019) · Science · doi:10.1126/science.aax8760 · Cited by 513
Creating perfused functional vascular channels using 3D bio-printing technology
Lee, V. K., Kim, D. Y., Ngo, H., Lee, Y., Seo, L., Yoo, S.-S., Vincent, P. A., & Dai, G. (2014) · Biomaterials · doi:10.1016/j.biomaterials.2014.05.083 · Cited by 494
Controllable Printing Droplets for High‐Resolution Patterns
Kuang, M., Wang, L., & Song, Y. (2014) · Advanced Materials · doi:10.1002/adma.201305416 · Cited by 479
Nakamura, K., Watanabe, T., Katayama, K., et al. (1972) · Journal of Applied Polymer Science · doi:10.1002/app.1972.070160503 · Cited by 475
Instant tough bonding of hydrogels for soft machines and electronics
Wirthl, D., Pichler, R., Drack, M., Kettlguber, G., Moser, R., Gerstmayr, R., Hartmann, F., Bradt, E., Kaltseis, R., Siket, C. M., et al. (2017) · Science Advances · doi:10.1126/sciadv.1700053 · Cited by 471
Synthesis, characterization and controlled drug release of thermosensitive IPN–PNIPAAm hydrogels
Zhang, X.-Z., Wu, D.-Q., & Chu, C.-C. (2004) · Biomaterials · doi:10.1016/j.biomaterials.2003.10.065 · Cited by 470
Conductive nanomaterials for 2D and 3D printed flexible electronics
Kamyshny, A., & Magdassi, S. (2019) · Chemical Society Reviews · doi:10.1039/c8cs00738a · Cited by 469
Capacitive Soft Strain Sensors via Multicore–Shell Fiber Printing
Frutiger, A., Muth, J. T., Vogt, D. M., Mengüç, Y., Campo, A., Valentine, A. D., Walsh, C. J., & Lewis, J. A. (2015) · Advanced Materials · doi:10.1002/adma.201500072 · Cited by 468
Biomimetic shark skin: design, fabrication and hydrodynamic function
Wen, L., Weaver, J. C., & Lauder, G. V. (2014) · Journal of Experimental Biology · doi:10.1242/jeb.097097 · Cited by 465
Liquid metal enabled microfluidics
Khoshmanesh, K., Tang, S.-Y., Zhu, J. Y., Schaefer, S., Mitchell, A., Kalantar-zadeh, K., & Dickey, M. D. (2017) · Lab on a Chip · doi:10.1039/c7lc00046d · Cited by 458
Ultrastretchable and Self-Healing Double-Network Hydrogel for 3D Printing and Strain Sensor
Liu, S., & Li, L. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b07445 · Cited by 456
Custom 3D printer and resin for 18 μm × 20 μm microfluidic flow channels
Gong, H., Bickham, B. P., Woolley, A. T., & Nordin, G. P. (2017) · Lab on a Chip · doi:10.1039/c7lc00644f · Cited by 443
3D Printing PDMS Elastomer in a Hydrophilic Support Bath via Freeform Reversible Embedding
Hinton, T. J., Hudson, A., Pusch, K., Lee, A., & Feinberg, A. W. (2016) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.6b00170 · Cited by 437
Stretchable materials of high toughness and low hysteresis
Wang, Z., Xiang, C., Yao, X., Le Floch, P., Mendez, J., & Suo, Z. (2019) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1821420116 · Cited by 433
Rapid Continuous Multimaterial Extrusion Bioprinting
Liu, W., Zhang, Y. S., Heinrich, M. A., De Ferrari, F., Jang, H. L., Bakht, S. M., Alvarez, M. M., Yang, J., Li, Y., Trujillo‐de Santiago, G., et al. (2017) · Advanced Materials · doi:10.1002/adma.201604630 · Cited by 424
3D Printing of Transparent and Conductive Heterogeneous Hydrogel–Elastomer Systems
Tian, K., Bae, J., Bakarich, S. E., Yang, C., Gately, R. D., Spinks, G. M., in het Panhuis, M., Suo, Z., & Vlassak, J. J. (2017) · Advanced Materials · doi:10.1002/adma.201604827 · Cited by 419
Additive manufacturing of biologically-inspired materials
Studart, A. R. (2016) · Chemical Society Reviews · doi:10.1039/c5cs00836k · Cited by 415
Oropallo, W., & Piegl, L. A. (2015) · Engineering With Computers · doi:10.1007/s00366-015-0407-0 · Cited by 406
Progress in the development of interpenetrating polymer network hydrogels
Myung, D., Waters, D., Wiseman, M., Duhamel, P., Noolandi, J., Ta, C. N., & Frank, C. W. (2008) · Polymers for Advanced Technologies · doi:10.1002/pat.1134 · Cited by 406
Structural quality of parts processed by fused deposition
Agarwala, M. K., Jamalabad, V. R., Langrana, N. A., Safari, A., Whalen, P. J., & Danforth, S. C. (1996) · Rapid Prototyping Journal · doi:10.1108/13552549610732034 · Cited by 406
Directed Colloidal Assembly of 3D Periodic Structures
Smay, J. E., Gratson, G. M., Shepherd, R. F., Cesarano, J., & Lewis, J. A. (2002) · Advanced Materials · doi:10.1002/1521-4095(20020916)14:18<1279::aid-adma1279>3.0.co;2-a · Cited by 388
Tough Composites Inspired by Mineralized Natural Materials: Computation, 3D printing, and Testing
Dimas, L. S., Bratzel, G. H., Eylon, I., & Buehler, M. J. (2013) · Advanced Functional Materials · doi:10.1002/adfm.201300215 · Cited by 385
A New 3D Printing Strategy by Harnessing Deformation, Instability, and Fracture of Viscoelastic Inks
Yuk, H., & Zhao, X. (2018) · Advanced Materials · doi:10.1002/adma.201704028 · Cited by 381
Lu, Y., Mapili, G., Suhali, G., Chen, S., & Roy, K. (2006) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.30601 · Cited by 380
Aqueous Two‐Phase Emulsion Bioink‐Enabled 3D Bioprinting of Porous Hydrogels
Ying, G., Jiang, N., Maharjan, S., Yin, Y., Chai, R., Cao, X., Yang, J., Miri, A. K., Hassan, S., & Zhang, Y. S. (2018) · Advanced Materials · doi:10.1002/adma.201805460 · Cited by 377
Inkjet printing ceramics: From drops to solid
Derby, B. (2011) · Journal of the European Ceramic Society · doi:10.1016/j.jeurceramsoc.2011.01.016 · Cited by 365
Soft Robotic Manipulation and Locomotion with a 3D Printed Electroactive Hydrogel
Han, D., Farino, C., Yang, C., Scott, T., Browe, D., Choi, W., Freeman, J. W., & Lee, H. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.8b04250 · Cited by 361
Yin, J., Lu, C., Fu, J., Huang, Y., & Zheng, Y. (2018) · Materials & Design · doi:10.1016/j.matdes.2018.04.029 · Cited by 360
Self-citationWüst, S., Godla, M. E., Müller, R., & Hofmann, S. (2014) · Acta Biomaterialia · doi:10.1016/j.actbio.2013.10.016 · Cited by 357
Multimaterial actinic spatial control 3D and 4D printing
Schwartz, J. J., & Boydston, A. J. (2019) · Nature Communications · doi:10.1038/s41467-019-08639-7 · Cited by 343
Gao, G., Schilling, A. F., Hubbell, K., Yonezawa, T., Truong, D., Hong, Y., Dai, G., & Cui, X. (2015) · Biotechnology Letters · doi:10.1007/s10529-015-1921-2 · Cited by 341
Microfluidic Printheads for Multimaterial 3D Printing of Viscoelastic Inks
Hardin, J. O., Ober, T. J., Valentine, A. D., & Lewis, J. A. (2015) · Advanced Materials · doi:10.1002/adma.201500222 · Cited by 340
Gao, G., Yonezawa, T., Hubbell, K., Dai, G., & Cui, X. (2015) · Biotechnology Journal · doi:10.1002/biot.201400635 · Cited by 340
An overview of the suitability of hydrogel-forming polymers for extrusion-based 3D-printing
Kirchmajer, D. M., Gorkin III, R., & in het Panhuis, M. (2015) · Journal of Materials Chemistry B · doi:10.1039/c5tb00393h · Cited by 337
Costantini, M., Testa, S., Mozetic, P., Barbetta, A., Fuoco, C., Fornetti, E., Tamiro, F., Bernardini, S., Jaroszewicz, J., Święszkowski, W., et al. (2017) · Biomaterials · doi:10.1016/j.biomaterials.2017.03.026 · Cited by 330
Review: Bioprinting: A Beginning
Mironov, V., Reis, N., & Derby, B. (2006) · Tissue Engineering · doi:10.1089/ten.2006.12.631 · Cited by 319
Three‐Dimensional Printing of Elastomeric, Cellular Architectures with Negative Stiffness
Duoss, E. B., Weisgraber, T. H., Hearon, K., Zhu, C., Small, W., Metz, T. R., Vericella, J. J., Barth, H. D., Kuntz, J. D., Maxwell, R. S., et al. (2014) · Advanced Functional Materials · doi:10.1002/adfm.201400451 · Cited by 316
Yang, Y., Chen, Z., Song, X., Zhang, Z., Zhang, J., Shung, K. K., Zhou, Q., & Chen, Y. (2017) · Advanced Materials · doi:10.1002/adma.201605750 · Cited by 316
Electrically assisted 3D printing of nacre-inspired structures with self-sensing capability
Yang, Y., Li, X., Chu, M., Sun, H., Jin, J., Yu, K., Wang, Q., Zhou, Q., & Chen, Y. (2019) · Science Advances · doi:10.1126/sciadv.aau9490 · Cited by 310
Bonding dissimilar polymer networks in various manufacturing processes
Liu, Q., Nian, G., Yang, C., Qu, S., & Suo, Z. (2018) · Nature Communications · doi:10.1038/s41467-018-03269-x · Cited by 309
An, B. W., Kim, K., Lee, H., Kim, S., Shim, Y., Lee, D., Song, J. Y., & Park, J. (2015) · Advanced Materials · doi:10.1002/adma.201502092 · Cited by 306
3D Printed Stem‐Cell Derived Neural Progenitors Generate Spinal Cord Scaffolds
Joung, D., Truong, V., Neitzke, C. C., Guo, S., Walsh, P. J., Monat, J. R., Meng, F., Park, S. H., Dutton, J. R., Parr, A. M., et al. (2018) · Advanced Functional Materials · doi:10.1002/adfm.201801850 · Cited by 306
Digitally Tunable Microfluidic Bioprinting of Multilayered Cannular Tissues
Pi, Q., Maharjan, S., Yan, X., Liu, X., Singh, B., van Genderen, A. M., Robledo‐Padilla, F., Parra‐Saldivar, R., Hu, N., Jia, W., et al. (2018) · Advanced Materials · doi:10.1002/adma.201706913 · Cited by 305
Rotational 3D printing of damage-tolerant composites with programmable mechanics
Raney, J. R., Compton, B. G., Mueller, J., Ober, T. J., Shea, K., & Lewis, J. A. (2018) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1715157115 · Cited by 301
Ink Jet Deposition of Ceramic Suspensions: Modeling and Experiments of Droplet Formation
Reis, N., & Derby, B. (2000) · MRS Proceedings · doi:10.1557/proc-625-117 · Cited by 289
Jayasinghe, S. N., Qureshi, A., & Eagles, P. A. M. (2005) · Small · doi:10.1002/smll.200500291 · Cited by 286
Ma, X., Yu, C., Wang, P., Xu, W., Wan, X., Lai, C. S. E., Liu, J., Koroleva-Maharajh, A., & Chen, S. (2018) · Biomaterials · doi:10.1016/j.biomaterials.2018.09.026 · Cited by 281
Self-assembled micro-organogels for 3D printing silicone structures
O’Bryan, C. S., Bhattacharjee, T., Hart, S., Kabb, C. P., Schulze, K. D., Chilakala, I., Sumerlin, B. S., Sawyer, W. G., & Angelini, T. E. (2017) · Science Advances · doi:10.1126/sciadv.1602800 · Cited by 277
4D Printing of Reversible Shape Morphing Hydrogel Structures
Naficy, S., Gately, R., Gorkin, R., Xin, H., & Spinks, G. M. (2017) · Macromolecular Materials and Engineering · doi:10.1002/mame.201600212 · Cited by 276
Dispensing nano–pico droplets and liquid patterning by pyroelectrodynamic shooting
Ferraro, P., Coppola, S., Grilli, S., Paturzo, M., & Vespini, V. (2010) · Nature Nanotechnology · doi:10.1038/nnano.2010.82 · Cited by 271
Actuating Soft Matter with Magnetic Torque
Erb, R. M., Martin, J. J., Soheilian, R., Pan, C., & Barber, J. R. (2016) · Advanced Functional Materials · doi:10.1002/adfm.201504699 · Cited by 271
Microdrop Printing of Hydrogel Bioinks into 3D Tissue‐Like Geometries
Pataky, K., Braschler, T., Negro, A., Renaud, P., Lutolf, M. P., & Brugger, J. (2012) · Advanced Materials · doi:10.1002/adma.201102800 · Cited by 267
3D Bioprinting of Vessel-like Structures with Multilevel Fluidic Channels
Gao, Q., Liu, Z., Lin, Z., Qiu, J., Liu, Y., Liu, A., Wang, Y., Xiang, M., Chen, B., Fu, J., et al. (2017) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.6b00643 · Cited by 267
Self-citation3D printing antagonistic systems of artificial muscle using projection stereolithography
Peele, B. N., Wallin, T. J., Zhao, H., & Shepherd, R. F. (2015) · Bioinspiration & Biomimetics · doi:10.1088/1748-3190/10/5/055003 · Cited by 265
Electrohydrodynamic direct-writing
Huang, Y., Bu, N., Duan, Y., Pan, Y., Liu, H., Yin, Z., & Xiong, Y. (2013) · Nanoscale · doi:10.1039/c3nr04329k · Cited by 258
Inkjet and inkjet-based 3D printing: connecting fluid properties and printing performance
Guo, Y., Patanwala, H. S., Bognet, B., & Ma, A. W. K. (2017) · Rapid Prototyping Journal · doi:10.1108/rpj-05-2016-0076 · Cited by 258
3D printing of a mechanically durable superhydrophobic porous membrane for oil–water separation
Lv, J., Gong, Z., He, Z., Yang, J., Chen, Y., Tang, C., Liu, Y., Fan, M., & Lau, W.-M. (2017) · Journal of Materials Chemistry A · doi:10.1039/c7ta02202f · Cited by 257
Materials perspective of polymers for additive manufacturing with selective laser sintering
Schmid, M., Amado, A., & Wegener, K. (2014) · Journal of Materials Research · doi:10.1557/jmr.2014.138 · Cited by 256
Hoch, E., Hirth, T., Tovar, G. E. M., & Borchers, K. (2013) · Journal of Materials Chemistry B · doi:10.1039/c3tb20745e · Cited by 255
Highly stretchable hydrogels for UV curing based high-resolution multimaterial 3D printing
Zhang, B., Li, S., Hingorani, H., Serjouei, A., Larush, L., Pawar, A. A., Goh, W. H., Sakhaei, A. H., Hashimoto, M., Kowsari, K., et al. (2018) · Journal of Materials Chemistry B · doi:10.1039/c8tb00673c · Cited by 252
Dimension‐Based Design of Melt Electrowritten Scaffolds
Hrynevich, A., Elçi, B. Ş., Haigh, J. N., McMaster, R., Youssef, A., Blum, C., Blunk, T., Hochleitner, G., Groll, J., & Dalton, P. D. (2018) · Small · doi:10.1002/smll.201800232 · Cited by 248
Zhou, W. Y., Lee, S. H., Wang, M., Cheung, W. L., & Ip, W. Y. (2008) · Journal of Materials Science: Materials in Medicine · doi:10.1007/s10856-007-3089-3 · Cited by 247
Zhai, X., Ma, Y., Hou, C., Gao, F., Zhang, Y., Ruan, C., Pan, H., Lu, W. W., & Liu, W. (2017) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.7b00224 · Cited by 243
Viscoplastic Matrix Materials for Embedded 3D Printing
Grosskopf, A. K., Truby, R. L., Kim, H., Perazzo, A., Lewis, J. A., & Stone, H. A. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b19818 · Cited by 243
Extrusion bioprinting of soft materials: An emerging technique for biological model fabrication
Jiang, T., Munguia-Lopez, J. G., Flores-Torres, S., Kort-Mascort, J., & Kinsella, J. M. (2019) · Applied Physics Reviews · doi:10.1063/1.5059393 · Cited by 243
3D printing of complex GelMA-based scaffolds with nanoclay
Gao, Q., Niu, X., Shao, L., Zhou, L., Lin, Z., Sun, A., Fu, J., Chen, Z., Hu, J., Liu, Y., et al. (2019) · Biofabrication · doi:10.1088/1758-5090/ab0cf6 · Cited by 242
Self-citationThree‐Dimensional Microvascular Fiber‐Reinforced Composites
Esser‐Kahn, A. P., Thakre, P. R., Dong, H., Patrick, J. F., Vlasko‐Vlasov, V. K., Sottos, N. R., Moore, J. S., & White, S. R. (2011) · Advanced Materials · doi:10.1002/adma.201100933 · Cited by 239
Melt flow behaviour of poly-ε-caprolactone in fused deposition modelling
Ramanath, H. S., Chua, C. K., Leong, K. F., & Shah, K. D. (2008) · Journal of Materials Science: Materials in Medicine · doi:10.1007/s10856-007-3203-6 · Cited by 239
Jin, Y., Liu, C., Chai, W., Compaan, A., & Huang, Y. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b03613 · Cited by 238
Multimaterial 3D Printing of Highly Stretchable Silicone Elastomers
Zhou, L.-Y., Gao, Q., Fu, J.-Z., Chen, Q.-Y., Zhu, J.-P., Sun, Y., & He, Y. (2019) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.9b04873 · Cited by 237
Self-citationRecycling of polyamide 12 based powders in the laser sintering process
Dotchev, K., & Yusoff, W. (2009) · Rapid Prototyping Journal · doi:10.1108/13552540910960299 · Cited by 229
Zhou, L., Fu, J., Gao, Q., Zhao, P., & He, Y. (2020) · Advanced Functional Materials · doi:10.1002/adfm.201906683 · Cited by 226
Self-citation3D Printing Gets a Boost and Opportunities with Polymer Materials
Hofmann, M. (2014) · ACS Macro Letters · doi:10.1021/mz4006556 · Cited by 225
Biomimetic strain hardening in interpenetrating polymer network hydrogels
Myung, D., Koh, W., Ko, J., Hu, Y., Carrasco, M., Noolandi, J., Ta, C. N., & Frank, C. W. (2007) · Polymer · doi:10.1016/j.polymer.2007.06.070 · Cited by 221
Highly Elastic, Transparent, and Conductive 3D‐Printed Ionic Composite Hydrogels
Odent, J., Wallin, T. J., Pan, W., Kruemplestaedter, K., Shepherd, R. F., & Giannelis, E. P. (2017) · Advanced Functional Materials · doi:10.1002/adfm.201701807 · Cited by 218
Material approaches to stretchable strain sensors
Park, J., You, I., Shin, S., & Jeong, U. (2015) · ChemPhysChem · doi:10.1002/cphc.201402810 · Cited by 216
Biologically Inspired Scaffolds for Heart Valve Tissue Engineering via Melt Electrowriting
Saidy, N. T., Wolf, F., Bas, O., Keijdener, H., Hutmacher, D. W., Mela, P., & De‐Juan‐Pardo, E. M. (2019) · Small · doi:10.1002/smll.201900873 · Cited by 215
Evaluation of bioink printability for bioprinting applications
Zhang, Z., Jin, Y., Yin, J., Xu, C., Xiong, R., Christensen, K., Ringeisen, B. R., Chrisey, D. B., & Huang, Y. (2018) · Applied Physics Reviews · doi:10.1063/1.5053979 · Cited by 214
3D Printed Multifunctional, Hyperelastic Silicone Rubber Foam
Chen, Q., Zhao, J., Ren, J., Rong, L., Cao, P., & Advincula, R. C. (2019) · Advanced Functional Materials · doi:10.1002/adfm.201900469 · Cited by 201
Strong fiber-reinforced hydrogel
Agrawal, A., Rahbar, N., & Calvert, P. D. (2013) · Acta Biomaterialia · doi:10.1016/j.actbio.2012.10.011 · Cited by 198
3D Printing of Interdigitated Dielectric Elastomer Actuators
Chortos, A., Hajiesmaili, E., Morales, J., Clarke, D. R., & Lewis, J. A. (2020) · Advanced Functional Materials · doi:10.1002/adfm.201907375 · Cited by 198
Mechanically Robust, Ultraelastic Hierarchical Foam with Tunable Properties via 3D Printing
Chen, Q., Cao, P., & Advincula, R. C. (2018) · Advanced Functional Materials · doi:10.1002/adfm.201800631 · Cited by 197
Foresti, D., Kroll, K. T., Amissah, R., Sillani, F., Homan, K. A., Poulikakos, D., & Lewis, J. A. (2018) · Science Advances · doi:10.1126/sciadv.aat1659 · Cited by 195
Lin, S., Cao, C., Wang, Q., Gonzalez, M., Dolbow, J. E., & Zhao, X. (2014) · Soft Matter · doi:10.1039/c4sm01039f · Cited by 193
Cited by
Bioinspired marine antifouling coatings: Status, prospects, and future
Jin, H., Tian, L., Bing, W., Zhao, J., & Ren, L. (2022) · Progress in Materials Science · doi:10.1016/j.pmatsci.2021.100889 · Cited by 585
Wang, H., Zhang, W., Ladika, D., Yu, H., Gailevičius, D., Wang, H., Pan, C., Nair, P. N. S., Ke, Y., Mori, T., et al. (2023) · Advanced Functional Materials · doi:10.1002/adfm.202214211 · Cited by 401
3D-printed self-healing hydrogels via Digital Light Processing
Caprioli, M., Roppolo, I., Chiappone, A., Larush, L., Pirri, C. F., & Magdassi, S. (2021) · Nature Communications · doi:10.1038/s41467-021-22802-z · Cited by 335
Tardy, B. L., Mattos, B. D., Otoni, C. G., Beaumont, M., Majoinen, J., Kämäräinen, T., & Rojas, O. J. (2021) · Chemical Reviews · doi:10.1021/acs.chemrev.0c01333 · Cited by 267
Emerging Technologies in Multi‐Material Bioprinting
Ravanbakhsh, H., Karamzadeh, V., Bao, G., Mongeau, L., Juncker, D., & Zhang, Y. S. (2021) · Advanced Materials · doi:10.1002/adma.202104730 · Cited by 266
Metadata
- Authors
- Zhou, L., Fu, J., & He, Y.
- Venue
- Advanced Functional Materials
- Publisher
- Wiley
- Published
- 2020-04-29
- Volume
- 30
- Issue
- 28
- ISSN
- 1616-301X (ISSN-L)
- 1616-3028
- OpenAlex
- W3023001773
- Cited by
- 713
- References
- 280
- FWCI
- 27.50
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.