The DOI matches its Crossref record; 27 of the 27 references it cites were found in a registry or an index.
A review of the operating limits in slot die coating processes
Open accessAbstract
Slot die coating is a pre‐metered process commonly used for producing thin and uniform films. It is an important film fabrication method for applications where precise coating is required. A major concern in slot die coating processes is how to determine the operating limits to set the appropriate range of operating parameters, including coating speed, flow rate, vacuum pressure, coating gap, liquid viscosity and surface tension, etc. Operating limits directly determine the effectiveness and efficiency of the process. In this article, the current state of academic research on operating limits in slot die coating processes is reviewed. Specifically, the theories, mechanisms, and empirical conclusions related to the limits on vacuum pressure, the low‐flow limit, the limit of wet thickness for zero‐vacuum‐pressure cases, the limit of dynamic wetting failure, and the limits of coating speed for a specific flow rate are reviewed. The article concludes with some recommendations for future work. © 2016 American Institute of Chemical Engineers AIChE J, 62: 2508–2524, 2016
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Bonn, D., Eggers, J., Indekeu, J., Meunier, J., & Rolley, E. (2009) · Reviews of Modern Physics · doi:10.1103/revmodphys.81.739 · Cited by 2,894
Roll‐to‐Roll fabrication of large area functional organic materials
Søndergaard, R. R., Hösel, M., & Krebs, F. C. (2013) · Journal of Polymer Science Part B: Polymer Physics · doi:10.1002/polb.23192 · Cited by 1,065
Upscaling of polymer solar cell fabrication using full roll-to-roll processing
Krebs, F. C., Tromholt, T., & Jørgensen, M. (2010) · Nanoscale · doi:10.1039/b9nr00430k · Cited by 1,024
Moving Contact Lines: Scales, Regimes, and Dynamical Transitions
Snoeijer, J. H., & Andreotti, B. (2013) · Annual Review of Fluid Mechanics · doi:10.1146/annurev-fluid-011212-140734 · Cited by 883
Dragging of a Liquid by a Moving Plate
LANDAU, L. D., & Levich, B. G. (1988) · Elsevier eBooks · doi:10.1016/b978-0-08-092523-3.50016-2 · Cited by 739
Weinstein, S. J. (2003) · Annual Review of Fluid Mechanics · doi:10.1146/annurev.fluid.36.050802.122049 · Cited by 551
Ambient fabrication of flexible and large-area organic light-emitting devices using slot-die coating
Sandström, A., Dam, H. F., Krebs, F. C., & Edman, L. (2012) · Nature Communications · doi:10.1038/ncomms2002 · Cited by 451
Blake, T. D., & Ruschak, K. J. (1979) · Nature · doi:10.1038/282489a0 · Cited by 261
Low‐flow limit in slot coating: Theory and experiments
Carvalho, M. S., & Kheshgi, H. S. (2000) · AIChE Journal · doi:10.1002/aic.690461003 · Cited by 231
Limiting flow in a pre-metered coating device
Ruschak, K. J. (1976) · Chemical Engineering Science · doi:10.1016/0009-2509(76)87026-1 · Cited by 204
Liquid film coating : scientific principles and their technological implications
Kistler, S. F., & Schweizer, P. (1997) · CERN Document Server (European Organization for Nuclear Research) · Cited by 202
Capillary pressure and viscous pressure drop set bounds on coating bead operability
Higgins, B. G., & Scriven, L. E. (1980) · Chemical Engineering Science · doi:10.1016/0009-2509(80)80018-2 · Cited by 182
Slot-die processing of lithium-ion battery electrodes—Coating window characterization
Schmitt, M., Baunach, M., Wengeler, L., Peters, K., Junges, P., Scharfer, P., & Schabel, W. (2012) · Chemical Engineering and Processing - Process Intensification · doi:10.1016/j.cep.2012.10.011 · Cited by 156
Low-flow limit in slot coating of dilute solutions of high molecular weight polymer
Romero, O. J., Suszynski, W. J., Scriven, L. E., & Carvalho, M. S. (2004) · Journal of Non-Newtonian Fluid Mechanics · doi:10.1016/j.jnnfm.2004.03.004 · Cited by 135
An experimental study of air entrainment at a solid/liquid/gas interface
Burley, R., & Kennedy, B. S. (1976) · Chemical Engineering Science · doi:10.1016/0009-2509(76)87040-6 · Cited by 125
Larsen‐Olsen, T. T., Andreasen, B., Andersen, T. R., Böttiger, A. P. L., Bundgaard, E., Norrman, K., Andreasen, J. W., Jørgensen, M., & Krebs, F. C. (2011) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2011.08.026 · Cited by 113
Coating and Drying Defects: Troubleshooting Operating Problems
Gutoff, E. B., & Cohen, E. D. (2006) · Wiley eBooks · doi:10.1002/0470044136 · Cited by 106
Lin, C., Wong, D. S., Liu, T., & Wu, P. (2010) · Advances in Polymer Technology · doi:10.1002/adv.20173 · Cited by 77
Wetting phenomena during processing of high-viscosity shear-thinning fluid
Bhamidipati, K. L., Didari, S., Bedell, P., & Harris, T. A. L. (2011) · Journal of Non-Newtonian Fluid Mechanics · doi:10.1016/j.jnnfm.2011.03.009 · Cited by 43
Self-citationEffect of shim configuration on flow dynamics and operability windows in stripe slot coating process
Han, G. H., Lee, S., Ahn, W.-G., Nam, J., & Jung, H. W. (2013) · Journal of Coatings Technology and Research · doi:10.1007/s11998-013-9485-3 · Cited by 43
Analysis of slot coating flow under tilted die
Lee, S., & Nam, J. (2015) · AIChE Journal · doi:10.1002/aic.14752 · Cited by 36
Membrane Electrode Assembly Fabrication Process for Directly Coating Catalyzed Gas Diffusion Layers
Ding, X., Didari, S., Fuller, T. F., & Harris, T. A. L. (2012) · Journal of The Electrochemical Society · doi:10.1149/2.103206jes · Cited by 36
Self-citationImproved Coating Window for Slot Coating
Chin, C., Wu, H., & Wang, S. S. (2010) · Industrial & Engineering Chemistry Research · doi:10.1021/ie801900t · Cited by 23
On the Pinning of Downstream Meniscus for Slot Die Coating
Lin, C., Wang, B.-K., Tiu, C., & Liu, T. (2012) · Advances in Polymer Technology · doi:10.1002/adv.21271 · Cited by 23
Operability window of slot coating using viscocapillary model for Carreau-type coating liquids
Koh, H. J., Kwon, I., Jung, H. W., & Hyun, J. C. (2012) · Korea-Australia Rheology Journal · doi:10.1007/s13367-012-0016-z · Cited by 22
Two-layer tensioned-web-over-slot die coating: Effect of operating conditions on coating window
Nam, J., & Carvalho, M. S. (2010) · Chemical Engineering Science · doi:10.1016/j.ces.2010.03.038 · Cited by 17
Wetting behavior of the shear thinning power law fluids
Didari, S., Ahmad, Z. Y., Veldhorst, J. D., & Harris, T. A. L. (2013) · Journal of Coatings Technology and Research · doi:10.1007/s11998-013-9503-5 · Cited by 9
Self-citation
Cited by
Scalable fabrication and coating methods for perovskite solar cells and solar modules
Park, N.-G., & Zhu, K. (2020) · Nature Reviews Materials · doi:10.1038/s41578-019-0176-2 · Cited by 908
Li, J., Fleetwood, J., Hawley, W. B., & Kays, W. (2022) · Chemical Reviews · doi:10.1021/acs.chemrev.1c00565 · Cited by 895
Zinc-ion batteries for stationary energy storage
Gourley, S. W. D., Brown, R., Adams, B. D., & Higgins, D. (2023) · Joule · doi:10.1016/j.joule.2023.06.007 · Cited by 482
The meniscus-guided deposition of semiconducting polymers
Gu, X., Shaw, L., Gu, K., Toney, M. F., & Bao, Z. (2018) · Nature Communications · doi:10.1038/s41467-018-02833-9 · Cited by 462
Electrode manufacturing for lithium-ion batteries—Analysis of current and next generation processing
Hawley, W. B., & Li, J. (2019) · Journal of Energy Storage · doi:10.1016/j.est.2019.100862 · Cited by 374
Metadata
- Authors
- Ding, X., Liu, J., & Harris, T. A. L.
- Venue
- AIChE Journal
- Publisher
- Wiley
- Published
- 2016-05-04
- Volume
- 62
- Issue
- 7
- Pages
- 2508-2524
- ISSN
- 0001-1541 (ISSN-L)
- 1547-5905
- OpenAlex
- W2328622841
- Cited by
- 294
- References
- 27
- FWCI
- 10.65
- Type
- journal article
- Language
- en
- Open access
- bronze
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.