The DOI matches its Crossref record; 32 of the 32 references it cites were found in a registry or an index.
Bioactive nanoparticles stimulate bone tissue formation in bioprinted three‐dimensional scaffold and human mesenchymal stem cells
Abstract
Bioprinting based on thermal inkjet printing is a promising but unexplored approach in bone tissue engineering. Appropriate cell types and suitable biomaterial scaffolds are two critical factors to generate successful bioprinted tissue. This study was undertaken in order to evaluate bioactive ceramic nanoparticles in stimulating osteogenesis of printed bone marrow‐derived human mesenchymal stem cells (hMSCs) in poly(ethylene glycol)dimethacrylate (PEGDMA) scaffold. hMSCs suspended in PEGDMA were co‐printed with nanoparticles of bioactive glass (BG) and hydroxyapatite (HA) under simultaneous polymerization so the printed substrates were delivered with highly accurate placement in three‐dimensional (3D) locations. hMSCs interacted with HA showed the highest cell viability (86.62 ± 6.02%) and increased compressive modulus (358.91 ± 48.05 kPa) after 21 days in culture among all groups. Biochemical analysis showed the most collagen production and highest alkaline phosphatase activity in PEG‐HA group, which is consistent with gene expression determined by quantitative PCR. Masson's trichrome staining also showed the most collagen deposition in PEG‐HA scaffold. Therefore, HA is more effective comparing to BG for hMSCs osteogenesis in bioprinted bone constructs. Combining with our previous experience in vasculature, cartilage, and muscle bioprinting, this technology demonstrates the capacity for both soft and hard tissue engineering with biomimetic structures.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Biodegradable and bioactive porous polymer/inorganic composite scaffolds for bone tissue engineering
Rezwan, K., Chen, Q. Z., Blaker, J. J., & Boccaccini, A. R. (2006) · Biomaterials · doi:10.1016/j.biomaterials.2006.01.039 · Cited by 3,839
Bruder, S. P., Jaiswal, N., & Haynesworth, S. E. (1997) · Journal of Cellular Biochemistry · doi:10.1002/(sici)1097-4644(199702)64:2<278::aid-jcb11>3.0.co;2-f · Cited by 1,485
A review on 3D micro-additive manufacturing technologies
Vaezi, M., Seitz, H., & Yang, S. (2013) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-012-4605-2 · Cited by 1,293
Mesenchymal stem cells: building blocks for molecular medicine in the 21st century
Caplan, A. I., & Bruder, S. P. (2001) · Trends in Molecular Medicine · doi:10.1016/s1471-4914(01)02016-0 · Cited by 1,138
Bryant, S. J., & Anseth, K. S. (2002) · Journal of Biomedical Materials Research · doi:10.1002/jbm.1217 · Cited by 845
Atomic force microscopy probing of cell elasticity
Kuznetsova, T. G., Starodubtseva, M. N., Yegorenkov, N. I., Chizhik, S. A., & Zhdanov, R. I. (2007) · Micron · doi:10.1016/j.micron.2007.06.011 · Cited by 794
Application of inkjet printing to tissue engineering
Boland, T., Xu, T., Damon, B., & Cui, X. (2006) · Biotechnology Journal · doi:10.1002/biot.200600081 · Cited by 783
Self-citationThree‐dimensional printing of porous ceramic scaffolds for bone tissue engineering
Seitz, H., Rieder, W., Irsen, S., Leukers, B., & Tille, C. (2005) · Journal of Biomedical Materials Research Part B: Applied Biomaterials · doi:10.1002/jbm.b.30291 · Cited by 742
Kon, E., Muraglia, A., Corsi, A., Bianco, P., Marcacci, M., Martin, I., Boyde, A., Ruspantini, I., Chistolini, P., Rocca, M., et al. (2000) · Journal of Biomedical Materials Research · doi:10.1002/(sici)1097-4636(20000305)49:3<328::aid-jbm5>3.0.co;2-q · Cited by 721
Human microvasculature fabrication using thermal inkjet printing technology
Cui, X., & Boland, T. (2009) · Biomaterials · doi:10.1016/j.biomaterials.2009.07.056 · Cited by 704
Self-citationDirect Human Cartilage Repair Using Three-Dimensional Bioprinting Technology
Cui, X., Breitenkamp, K., Finn, M. G., Lotz, M., & D'Lima, D. D. (2012) · Tissue Engineering Part A · doi:10.1089/ten.tea.2011.0543 · Cited by 686
Self-citationThermal Inkjet Printing in Tissue Engineering and Regenerative Medicine
Cui, X., Boland, T., D.D'Lima, D., & K. Lotz, M. (2012) · Recent Patents on Drug Delivery & Formulation · doi:10.2174/187221112800672949 · Cited by 581
Self-citationBone tissue engineering therapeutics: controlled drug delivery in three-dimensional scaffolds
Mouriño, V., & Boccaccini, A. R. (2010) · Journal of The Royal Society Interface · doi:10.1098/rsif.2009.0379 · Cited by 527
Regulation of Osteoblast Differentiation by Runx2
Komori, T. (2009) · Advances in Experimental Medicine and Biology · doi:10.1007/978-1-4419-1050-9_5 · Cited by 526
Photoencapsulation of chondrocytes in poly(ethylene oxide)-based semi-interpenetrating networks
Elisseeff, J., McIntosh, W., Anseth, K., Riley, S., Ragan, P., & Langer, R. (2000) · Journal of Biomedical Materials Research · doi:10.1002/(sici)1097-4636(200008)51:2<164::aid-jbm4>3.0.co;2-w · Cited by 510
Assessment of bone ingrowth into porous biomaterials using MICRO-CT
Jones, A. C., Arns, C. H., Sheppard, A. P., Hutmacher, D. W., Milthorpe, B. K., & Knackstedt, M. A. (2007) · Biomaterials · doi:10.1016/j.biomaterials.2007.01.046 · Cited by 422
Isolation and characterization of osteoblast precursor cells from human bone marrow
Rickard, D. J., Kassem, M., Hefferan, T. E., Sarkar, G., Spelsberg, T. C., & Riggs, B. L. (1996) · Journal of Bone and Mineral Research · doi:10.1002/jbmr.5650110305 · Cited by 396
A Tissue Engineering Solution for Segmental Defect Regeneration in Load-Bearing Long Bones
Reichert, J. C., Cipitria, A., Epari, D. R., Saifzadeh, S., Krishnakanth, P., Berner, A., Woodruff, M. A., Schell, H., Mehta, M., Schuetz, M. A., et al. (2012) · Science Translational Medicine · doi:10.1126/scitranslmed.3003720 · Cited by 364
Cell damage evaluation of thermal inkjet printed Chinese hamster ovary cells
Cui, X., Dean, D., Ruggeri, Z. M., & Boland, T. (2010) · Biotechnology and Bioengineering · doi:10.1002/bit.22762 · Cited by 364
Self-citationDexamethasone induction of osteoblast mRNAs in rat marrow stromal cell cultures
Leboy, P. S., Beresford, J. N., Devlin, C., & Owen, M. E. (1991) · Journal of Cellular Physiology · doi:10.1002/jcp.1041460306 · Cited by 343
Synthesis and Characterization of PEG Dimethacrylates and Their Hydrogels
Lin-Gibson, S., Bencherif, S., Cooper, J. A., Wetzel, S. J., Antonucci, J. M., Vogel, B. M., Horkay, F., & Washburn, N. R. (2004) · Biomacromolecules · doi:10.1021/bm0498777 · Cited by 277
Human Mesenchymal Stem Cell Proliferation and Osteogenic Differentiation in Fibrin Gels in Vitro
Catelas, I., Sese, N., Wu, B. M., Dunn, J. C. Y., Helgerson, S., & Tawil, B. (2006) · Tissue Engineering · doi:10.1089/ten.2006.12.2385 · Cited by 225
Spalazzi, J. P., Doty, S. B., Moffat, K. L., Levine, W. N., & Lu, H. H. (2006) · Tissue Engineering · doi:10.1089/ten.2006.12.3497 · Cited by 215
3D powder printed calcium phosphate implants for reconstruction of cranial and maxillofacial defects
Klammert, U., Gbureck, U., Vorndran, E., Rödiger, J., Meyer-Marcotty, P., & Kübler, A. C. (2010) · Journal of Cranio-Maxillofacial Surgery · doi:10.1016/j.jcms.2010.01.009 · Cited by 213
Spalazzi, J. P., Dagher, E., Doty, S. B., Guo, X. E., Rodeo, S. A., & Lu, H. H. (2008) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.32073 · Cited by 191
Bioactive Stratified Polymer Ceramic-Hydrogel Scaffold for Integrative Osteochondral Repair
Jiang, J., Tang, A., Ateshian, G. A., Guo, X., Hung, C. T., & Lu, H. H. (2010) · Annals of Biomedical Engineering · doi:10.1007/s10439-010-0038-y · Cited by 157
Cui, X., Breitenkamp, K., Lotz, M., & DʼLima, D. D. (2012) · Biotechnology and Bioengineering · doi:10.1002/bit.24488 · Cited by 120
Self-citationAccelerated myotube formation using bioprinting technology for biosensor applications
Cui, X., Gao, G., & Qiu, Y. (2012) · Biotechnology Letters · doi:10.1007/s10529-012-1087-0 · Cited by 109
Self-citationHuman Cartilage Tissue Fabrication Using Three-dimensional Inkjet Printing Technology
Cui, X., Gao, G., Yonezawa, T., & Dai, G. (2014) · Journal of Visualized Experiments · doi:10.3791/51294 · Cited by 87
Self-citationFunctional barrier principle for growth-factor-based articular cartilage repair
Hunziker, E. B., & Driesang, I. M. K. (2003) · Osteoarthritis and Cartilage · doi:10.1016/s1063-4584(03)00031-1 · Cited by 61
Cui, X., Hasegawa, A., Lotz, M., & DʼLima, D. D. (2012) · Biotechnology and Bioengineering · doi:10.1002/bit.24495 · Cited by 61
Self-citationImage based printing of structured biomaterials for realizing complex 3D cardiovascular constructs
Boland, T., Cui, X., Aho, M., Baicu, C., & Zile, M. R. (2006) · Technical programs and proceedings/Technical program and proceedings · doi:10.2352/issn.2169-4451.2006.22.2.art00028_3 · Cited by 2
Self-citation
Cited by
Bioinks for 3D bioprinting: an overview
Gungor-Ozkerim, P. S., Inci, I., Zhang, Y. S., Khademhosseini, A., & Dokmeci, M. R. (2018) · Biomaterials Science · doi:10.1039/c7bm00765e · Cited by 1,428
Progress in 3D bioprinting technology for tissue/organ regenerative engineering
Matai, I., Kaur, G., Seyedsalehi, A., McClinton, A., & Laurencin, C. T. (2020) · Biomaterials · doi:10.1016/j.biomaterials.2019.119536 · Cited by 1,156
The bioink: A comprehensive review on bioprintable materials
Hospodiuk, M., Dey, M., Sosnoski, D., & Ozbolat, I. T. (2017) · Biotechnology Advances · doi:10.1016/j.biotechadv.2016.12.006 · Cited by 1,118
3D printing of hydrogels: Rational design strategies and emerging biomedical applications
Li, J., Wu, C., Chu, P. K., & Gelinsky, M. (2020) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2020.100543 · Cited by 862
A comprehensive review on droplet-based bioprinting: Past, present and future
Gudapati, H., Dey, M., & Ozbolat, I. (2016) · Biomaterials · doi:10.1016/j.biomaterials.2016.06.012 · Cited by 859
Metadata
- Authors
- Gao, G., Schilling, A. F., Yonezawa, T., Wang, J., Dai, G., & Cui, X.
- Venue
- Biotechnology Journal
- Publisher
- Wiley
- Published
- 2014-09-10
- Volume
- 9
- Issue
- 10
- Pages
- 1304-1311
- ISSN
- 1860-6768 (ISSN-L)
- 1860-7314
- OpenAlex
- W2069520190
- Cited by
- 351
- References
- 32
- FWCI
- 12.08
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.